01277 525 020
Mon–Fri 8am–5pmSectorsFAQAccreditations
01277 525 020Get a quote

South East England and London

Floor Joint Sealing in Kent

Floor joint sealing in all 931 towns and villages of Kent, done properly, with a fixed quote before we start and a 12-month guarantee.

Floor Joint Sealing in Kent

Share the site address and what’s failing, and we’ll reply with a fixed quote or arrange a visit.

Ask for a quote01277 525 020

Where we work in Kent

Floor joint sealing and filling in warehouses, factories and industrial units. Pick your town below to see the details for your area, or call or email us for a quote.

Largest places

Also in Kent

Postcode districts

Floor joint sealing across Kent: what to expect

Sometimes the concrete either side of a joint has already spalled. A filler laid against broken edges has nothing sound to grip, so we will tell you if the joint edges need repairing first and leave that decision with you. The enquiries we see most involve scruffy, dirty joint lines on a shop or showroom floor and a gap opening alongside old joint filler, on saw-cut induced joints, construction joints and forklift and pallet-truck routes.

Before we leave any area, we remove the tape, clean down and inspect every joint, ready for your sign-off. Where the sealant needs time to cure before use, we tell you and sign the area.

  1. First, the zones and order of work are agreed with you.
  2. Any joints with broken edges are flagged before work starts.
  3. Failed material and debris are removed and the joint cleaned.
  4. The chosen filler or sealant goes in flush with the slab.
  5. You get a time for each zone to reopen.

What you will pay

The work involved drives the cost: stripping out, preparation, sealing, access and phasing. Call for a fixed quote and we will explain how it’s made up.

Why clients in Kent choose us

  • Over 20 years of commercial sealing
  • Clear, fixed quotes
  • One contact handling all your sites
  • 12-month guarantee on workmanship

Getting a fixed quote

Quotes are fixed against the scope you send, so the cost is agreed before work starts. To start the process, phone 01277 525 020 or email a schedule or drawings.

Around Maidstone

Around Maidstone, our work takes us to commercial buildings near Paper Makers Arms, Maidstone Grammar School and St Philip's Church and the streets around them. Also close by are River Len LNR (under half a mile north-east), South Borough Primary School (less than half a mile south) and St Augustine Academy (1.2 miles west). Maidstone’s nearest station is Maidstone West station, about 0.6 miles north-west of the centre. A little further out are Maidstone Carriage Museum (less than half a mile north-west) and Oakwood Hospital (1.8 miles west). For a walk, there’s Burham Down and Boxley Hills.

Floors, slabs and movement joints across Kent

Most floor and movement joint work across Kent has to happen while sites keep operating, so we phase it bay by bay, aisle by aisle or deck by deck.

We work across Greater London and the South East counties, and every job in Kent starts with access, parking and site rules. Coastal places in Kent often have hotels, guest houses and holiday accommodation with busy seasons, which makes the quieter months a good time for sealant work.

Maidstone: Retail centres such as The Mall Maidstone, 0.5 miles to the north of Maidstone, have floors, service yards and car parks with joints under constant traffic. Campuses like University for the Creative Arts, 1.3 miles to the west of Maidstone, mix old and new buildings, with movement joints wherever they meet.

Different surfaces, different methods

Semi-rigid joint fillers

If a joint is still opening, a semi-rigid filler may part from one face. A later top-up typically puts that right and we’ll flag it at quote stage.

Isolation joints at walls and columns

We plan column and wall joints around racking and fixed plant so nothing has to move unexpectedly.

When it isn’t the sealant

Being straight saves everyone time. New sealant won’t cure:

  • Spalled arrises, which need an edge repair first
  • Worn screed or surface finishes
  • A floor that is out of level for the racking or trucks

Looking after the joints

Once the work is signed off, a little attention goes a long way:

  • Mention any aggressive cleaning regime at quote stage
  • Allow for topping up joints as a new slab settles
  • Photograph any joint that starts to chip
  • Check joint lines on busy aisles regularly

Once cured, the joints get cleaned along with the slab. Tell us about aggressive cleaning products or hot washing at quote stage so the product suits them.

Every day an open joint stays full of grit, the edges take more punishment. Getting it filled stops the damage before it becomes a repair.

What sets the cost

What shapes the price:

  • How much there is to seal
  • Working within restricted access windows
  • How accessible the joints are
  • Whether old sealant has to be cut out first

Whether it’s a single area or a whole estate, the same things set the price: what’s in scope, how we reach it, what’s specified and when it needs doing. Call for a quote, and you’ll have a fixed figure to work with.

What we need to price the job

Diagnosis starts before we arrive. Tell us:

  • How the joints are reached, and at what height
  • The site address and postcode
  • Drawings or a marked-up plan, if available
  • When you need the work done

If there’s a specification, drawings or a tender package, send it with your enquiry, and we will price against exactly what is specified. For smaller jobs, photographs and a description will do.

Should maintenance staff do it?

The visible bead is only part of the job. Correct depth, the right primer and a sealant matched to the movement are easy to get wrong without experience.

For a quick touch-up, site staff may be fine, but larger jobs are different: a specialist brings efficiency, a consistent finish and a 12-month guarantee.

Questions we’re asked in Kent

What site paperwork can you supply?

Let us know which documents the site needs, such as RAMS, an insurance certificate or CSCS details, and we’ll confirm them with the quote.

When can forklifts run over new joint filler?

The wait is set by the product’s cure time, and cold floors slow it down. Phasing is planned with that in mind.

Can the sealant be colour-matched?

In many cases, yes. Sealants are made in a wide range of standard colours, and matching to RAL references or nearby finishes is commonly requested. We’ll confirm the colours available for the specified product.

How long do sealant joints last?

Nobody can honestly give a figure in years, because life depends on how much the joint moves, how exposed it is and how it’s cleaned and used. Regular inspection is the best way to catch problems early.

What happens if the joint edges are damaged?

Filling against broken edges doesn’t last. We will tell you if the joint edges need repairing first, so you can decide how to proceed.

Do you work to architects’ specifications?

Yes. Send it with your enquiry, and we’ll price the work to it, flagging anything that needs clarifying.

What do you need from us to quote?

Send details through our quote form or by email, with the traffic on each area. A fixed quote follows with the product and phasing set out.

Every town and village in Kent

A

B

C

D

E

F

G

H

I

J

K

L

M

N

O

P

Q

R

S

T

U

V

W

Y

Accreditations

Trusted. Accredited. Insured.