Felderland floor joint sealing
Floor joint sealing for Felderland, from a contractor working since 2005. Fully insured and CHAS accredited.
- A rough ride across broken joints
- Soft sealant dragged out of trafficked joints
- Joint edges breaking up under truck wheels
Need floor joint sealing in Felderland?
Send drawings, photos or a joint schedule, or tell us about the site, and we’ll come back with a fixed quote.
Floor joint sealing in Felderland, done properly
Few warehouses can shut a whole floor while joints are done, so we phase the work aisle by aisle or bay by bay. Tell us your site hours and access windows and we will plan around them, with goods still moving in the areas we aren’t in. We work on retail and showroom floors, saw-cut induced joints and forklift and pallet-truck routes, and the failures we are asked to look at most are open saw cuts full of debris and loading bay joints breaking down. Searching for sealant specialists in Felderland? We’ve been sealing commercial buildings since 2005, CHAS accredited and a Constructionline member.
Around smaller places such as Felderland, floor joints are often in barns and farm buildings turned into workshops, stores and offices. Whether it’s a farm store turned workshop or a storage unit, the joints need a product that suits the traffic.
Work we carry out comes with a 12-month guarantee. Should something we installed fail, call the office on 01277 525 020 or email a schedule or drawings and we’ll come back to it.
- Where
- Felderland (CT14)
- Wider area
- Kent
- Guarantee
- 12 months on every job
- Price
- Fixed quote, scope in writing
- Phone
- 01277 525 020
- Last updated
- 3 November 2026
What the job involves on each surface
Flexible floor sealants
Polyurethane sealants suit floor joints with larger movement. They don’t hold the arrises up as firmly as a semi-rigid fill, so they suit lighter traffic or movement joints.
Semi-rigid joint fillers
A semi-rigid filler is stiff enough to hold the arrises up when wheels cross. They allow only small movement, so they suit joints where most shrinkage has already happened.
Our process
Working in a building that stays open takes some planning. We sign and contain the area we’re in, keep walkways clear and work section by section so the rest of the building stays in use. Rural sites near Felderland may need directions, gate codes or a contact on site. Send that with the details and we’ll confirm the plan with the quote.
- A floor survey records every joint, its edges and what crosses it.
- You receive a fixed quote showing products and phasing.
- Each joint is cut or routed back to clean, sound concrete.
- Dust is vacuumed out and primer applied where specified.
- The joint is filled to its specified depth and trimmed level.
- We hand each phase back when it can take traffic.
Before we start on site
- Send any specification or drawings in advance
- Let building users know which areas are affected
- Agree which areas must stay open
Quotes
Photos, drawings or a schedule of the joints are often enough for a fixed quote. If the job needs a look first, we will arrange a site visit.
Advice
Doing it in-house
The visible bead is only part of the job. Correct depth, the right primer and a sealant matched to the movement are easy to get wrong without experience.
Redoing a failed joint usually costs more than getting it right at the outset, because the whole bead must be removed and the faces cleaned back again. For that reason, many FMs and contractors use a sealant specialist from the outset.
Common questions from Felderland clients
Is a smaller place like Felderland outside your area?
Not at all: smaller places are covered as well as towns. Our area covers London and the South East counties. Good photographs up front let us bring everything on the first visit.
Can being near the sea in Felderland affect the sealant we need?
It can. Coastal exposure works external joints harder than inland weather. Product choice and preparation matter more, and sea-facing elevations are worth inspecting more often.
Do you repair broken joint edges?
Filling against broken edges doesn’t last. If the arrises have spalled, we’ll say they need repair before filling and set out how that affects the job.
Will your applicators have CSCS cards?
Yes. If you need card details for site access, tell us and we’ll confirm them with the quote.
What information helps you price floor joint sealing?
Use our quote form, or email photos and a plan and tell us what runs on the floor. We then send a fixed quote with the product and phasing set out.
What guarantee do you give on joint filling?
Our workmanship carries a 12-month guarantee and the work is covered by public liability insurance.
What happens if old sealant might contain asbestos?
Some older mastics, especially in pre-2000 buildings, can contain asbestos. Before we disturb old sealant in an older building, we ask to see the asbestos register or survey, and work stops until any suspect material has been tested. Removing asbestos is a job for asbestos specialists, not us.
Why deal with it now?
Some runs only need partial renewal or topping up. Where existing filler is well bonded and the gap beside it is small, a full strip-out isn’t always needed and the quote shows which approach suits each run. Older rural buildings around Felderland move with the seasons, and rigid or tired sealant can’t keep up. A sealant with the right movement capability, correctly sized, lasts far better.
Whether it’s a single area or a whole estate, the same things set the price: what’s in scope, how we reach it, what’s specified and when it needs doing. Call for a quote and we’ll put a fixed figure on it.
Why appoint us
- Public liability insurance in place
- Specification-led, product-correct work
- 12 months’ guarantee on every job
- Old sealant cut out, never sealed over
Take a look at our cost guide or how we’re accredited.
Floor joint sealing around Felderland: points for this area
Felderland lies within about 3 miles of the sea. External movement joints in car parks, ramps and yards near the coast take salt and wind-driven rain on top of traffic, so it pays to keep them sealed. Felderland is about 64 miles from central London. Distribution warehouses and industrial estates are common around the motorway corridors that serve the capital.
On a site such as Birnham Farm Business Centre, which lies west of Felderland, the movement joints are in car park slabs, paving and building elevations. For a school such as Sandwich Technology School, playground and building joints can be done in the holidays.
Felderland is about 4 miles north-west of Deal, in Kent. Looking for floor joint sealing in Felderland? We can help. Felderland is one of 931 places in Kent on our list. London is covered too, some 64 miles away.
Work on floor joints is covered throughout CT14, for business premises of every kind. Among the streets we cover are Felderland Lane, Felderland Close and Deal Road, and sites on any of them can send details for a fixed quote. Nearby places we also cover include Statenborough (1 mile west), Worth (1 mile east), Ham (1 mile south), Woodnesborough (1 mile north-west) and Sandwich (1 mile north) for floor joints. Nearby towns on our patch include Canterbury (11 miles west), Margate (9 miles north), Dover (8 miles south), Folkestone (14 miles south-west), Ramsgate (7 miles north-east) and Broadstairs (8 miles north-east).
Local landmarks in Felderland
In Felderland, that means premises near The Blue Pigeons pub, Worth Primary School and Ham Fen, among other places. The nearest railway station is Sandwich station, roughly 1 mile north-east. A little further out are Sandown Castle (3.3 miles south-east) and The Precinct Toy Collection (1.4 miles north). For a walk, there’s Monk's Wall nature reserve.
What sealant work can’t fix
Before quoting, we check that sealant is the right answer. It isn’t the answer for:
- Joint edges that have already broken away, which need repairing before filling (we’ll tell you if so)
- Structural cracking in the slab
- Unstable slabs moving under traffic
Not sure which it is? You can ring 01277 525 020 or send photos by email and we will tell you honestly.
Where we work in Felderland
- Saw-cut induced joints
- Joints along racking aisles
- Forklift and pallet-truck routes
- Retail and showroom floors
- Loading bays
- Construction joints
Looking after the joints
Every sealant joint needs some looking after, and their life depends on movement, exposure, cleaning and use. We suggest:
- Expect fillers on young slabs to need a top-up
- Hold traffic back until the product has cured
- Remind operators to lift rather than drag
- Make joint checks part of your floor inspections
Young concrete carries on shrinking, so some fillers part slightly from one face. It is a known trait of new floors and a later top-up deals with it.
Every day an open joint stays full of grit, the edges take more punishment. Getting it filled stops the damage while it is still a straightforward job.