Industrial and floor joint sealing in Silver Street, Kent
Work needed on a floor joint in Silver Street? We look at it, seal it with the right product and hand it over with a 12-month guarantee.
- A rough ride across broken joints
- Untidy open joints in a retail unit
- Joint edges breaking up under truck wheels
Floor joint sealing in Silver Street
Share the site address and what’s failing, and we’ll reply with a fixed quote or arrange a visit.
About our floor joint sealing in Silver Street
Concrete floors in warehouses and factories are cut into bays with saw cuts and day joints, and every one of those joints is an exposed edge under hard wheels. Our job is to put the right filler or sealant into them for the loads and the movement they see, so the arrises are supported and grit stays out. We work on construction joints, saw-cut induced joints and loading bays, and what we are called in for most is scruffy, dirty joint lines on a shop or showroom floor and a rough ride across broken joints. Facilities teams, main contractors and managing agents in Silver Street tend to want the same three things: a fixed quote, no surprises on site and a 12-month guarantee behind the result.
In and around smaller places like Silver Street, the concrete floors we see are often in converted farm buildings, small workshops and storage units. Joints in those slabs take vehicles, trolleys and foot traffic, and need a filler or sealant to match.
Every job we finish is backed by a 12-month workmanship guarantee, wherever the site is. If a joint we sealed fails because of how it was installed, we come back and put it right.
- Where
- Silver Street (ME9)
- Region
- Kent
- Cover
- 12 months on every job
- Price
- Quoted before any work starts
- Telephone
- 01277 525 020
- Page updated
- 3 November 2026
Our process
Before any cutting starts, the area is protected: masking tape along the joint edges and sheeting over anything nearby. The work itself normally takes a day for smaller units, with bigger warehouse floors programmed over several visits, and our waste is bagged and taken away as we go. Jobs in and around smaller places like Silver Street are normally planned as a single visit, so we ask for photos and rough sizes first. That way the right products come on the day.
- We walk the floor and mark up joint widths, edge damage and traffic routes.
- The treatment and the zones are set out in a fixed quote.
- Each joint is cut or routed back to clean, sound concrete.
- We extract the dust and prime the faces if the product needs it.
- Filler or sealant is placed to depth and finished flush.
- Zones reopen once cured and the work moves on.
Before we start on site
- Agree which areas must stay open
- Tell staff and tenants when we’ll be in
- Tell us what induction or permit system the site runs
Quotes
For a fixed quote, ring 01277 525 020 or email the details over. Our quote form is another easy route.
Advice
Surface by surface
Flexible floor sealants
Polyurethane sealants suit floor joints with larger movement. They give less edge support than semi-rigid fillers, so they suit lighter traffic or movement joints.
Retail and showroom floors
We plan shop-floor work so trading can continue. Tell us your site hours and access windows and we will plan around them.
Common questions from Silver Street clients
Is Silver Street too far out for you?
Not at all. Silver Street is within our area. We cover Greater London and the counties of the South East. Send photographs and a list of what needs doing, and we’ll plan the job to need as few trips as possible.
Is Kent Science Park, near Silver Street, within your area?
Yes. We cover Silver Street and the area around it, including industrial estates, business parks and retail parks such as Kent Science Park. A few photographs and the unit address let us price the work.
How long does a job like this take?
We plan the time on site around your programme and access. You’ll have an expected duration with the quote.
What happens if the joint edges are damaged?
A filler needs sound edges to grip. If the arrises have spalled, we will say they need repair before filling and set out how that affects the job.
Is colour matching possible?
It depends on the product specified. Some ranges are wide, others limited, so the available colours are confirmed with the quote.
Why is there a gap next to the joint filler?
Young concrete carries on shrinking for a long time and a stiff filler can separate down one side. A top-up normally puts it right.
What about RAMS and site documents?
Tell us what site paperwork you need (RAMS, insurance certificate, CSCS details) and we will confirm with the quote.
Why act early in Silver Street
Some runs only need partial renewal or topping up. Where existing filler is well bonded and the gap beside it is small, a full strip-out isn’t always needed and the quote shows which approach suits each run. One visit to deal with every failing joint makes more sense than several trips to a place like Silver Street. Send photographs of each area and we will quote for the lot.
The product called for affects the cost, as does the preparation each joint needs, from cutting out to priming and backing rod. Access, phasing and site requirements come into it too.
Why appoint us
- Our applicators hold CSCS cards
- Over 20 years of commercial sealing
- One phone line for London, the South East and Scotland
- Failed material removed, not covered up
See how commercial sealant jobs are priced and our accreditations.
Should maintenance staff do it?
Putting right a botched joint often costs more than sealing it well at the start, since all of it has to come out and the faces be cleaned back again. That’s why many clients bring in a specialist from the beginning.
There’s also the paperwork. Main contractors and clients often ask for CSCS cards, RAMS and insurance details, and we’ll confirm the paperwork you need with the quote.
Where floor joints take the most wear near Silver Street
The South East is one of the drier parts of the UK. External joints still wait for dry conditions, and gritting in cold spells finds its way into open joints. Central London is about 36 miles from Silver Street. Distribution warehouses and industrial estates are common around the motorway corridors that serve the capital; their floors carry heavy traffic every shift.
For an estate such as Sittingbourne Memorial Hospital, 2.5 miles to the north-east of Silver Street, the joints in ramps, decks and long building elevations all need attention over time. Campuses like Canterbury Christ Church University (to the south of Silver Street) mix old and new buildings, with movement joints wherever they meet.
Silver Street is about 3 miles south-west of Sittingbourne, in Kent. Our applicators travel to Silver Street for work on floor joints, handled exactly as we handle every other area. Our Kent coverage takes in 931 places. Our London page has more on work in that area (36 miles or so).
Work on floor joints is covered throughout ME9, for business premises of every kind. If your building is just outside Silver Street, we cover Bredgar (1 mile east), Oad Street (1 mile north-west), South Green (2 miles west), Danaway (2 miles north-west) and Chestnut Street (2 miles north). A short drive away, we cover Maidstone (8 miles south-west), Ashford (14 miles south-east), Sittingbourne (3 miles north-east), Whitstable (15 miles east), Faversham (8 miles east) and Minster (9 miles north-east).
Landmarks near Silver Street
Around Silver Street, our work takes us to commercial buildings near Westlands School and Cromers Wood and the streets around them. Silver Street’s nearest station is Sittingbourne station, about 2.8 miles north-east of the centre. Other landmarks nearby include Sittingbourne Heritage Museum (2.9 miles north-east) and Bayford Court (3.1 miles north-east). The countryside around Silver Street includes Detling Hill.
Places near Silver Street
More services for Silver Street
What we’re called out for in Silver Street
Older fills harden, shrink and crack with age especially under daily scrubbing and traffic. At that point it neither holds the edges nor keeps debris out.
These are often picked up first by site or facilities staff:
- Untidy open joints in a retail unit
- Unfilled floor joints collecting dirt and grit
- Joint fill separating from the concrete
- Failing joints at loading bays and dock doors
Schools such as Bredgar Church of England Primary School have movement joints in their walls and floors that are easy to overlook.
What to look for in a quote
- Can the work be phased to keep areas open?
- Do they follow the manufacturer’s priming guidance?
- Who will actually carry out the work
- Will RAMS and insurance details be available?
What sealant work can’t fix
Not every problem is a sealant problem, and we are upfront when that’s the case. It won’t fix:
- Unstable slabs moving under traffic
- Worn screed or surface finishes
- Spalled arrises, which need an edge repair first
Not sure which it is? You can ring 01277 525 020 or send details through our quote form and we’ll tell you honestly before you book.
Where we work in Silver Street
- Joints along racking aisles
- Loading bays
- Retail and showroom floors
- Construction joints
- Saw-cut induced joints
- Forklift and pallet-truck routes