Industrial and floor joint sealing in Hunton, Kent
Our CSCS-carded applicators take on floor joint sealing and filling in warehouses, factories and industrial units in Hunton. Send photos or drawings for a fixed quote.
- Scruffy, dirty joint lines on a shop or showroom floor
- Cracked and crumbling joint fill
- Filler that has parted from one face
Floor joint sealing across Hunton
Send drawings, photos or a joint schedule, or tell us about the site, and we’ll come back with a fixed quote.
How the quote is worked out
Sealant work doesn’t have a standard rate, since sites vary so much. What we take into account:
- Whether old sealant has to be cut out first
- The total length or number of joints
- Which sealant the job calls for
- Access and working height
A quote for floor joints depends on quantities, condition and access, plus any specification you’re working to. Call for a quote.
Details that help us quote
The more we know, the firmer the quote. Helpful details to send:
- Anything awkward about access or site hours
- Drawings or a marked-up plan, if available
- The postcode of the building
- A wide shot and a close-up of the area
We quote a fixed sum against the scope you give us, so you know the figure before anyone is on site. To start the process, call 01277 525 020 or email a schedule or drawings.
Floor joint sealing in Hunton, done properly
Mastic Doctor has worked on joints in commercial buildings for over 20 years. Our CSCS-carded applicators follow your site induction and rules, and the business is CHAS accredited and a Constructionline member holding public liability insurance. Finished floor joints in Hunton carry our 12-month guarantee. We work on forklift and pallet-truck routes, retail and showroom floors and saw-cut induced joints, and the usual reasons a site gets in touch are a gap opening alongside old joint filler and brittle joint filler breaking up. A specialist sealant contractor works differently from a general builder: in Hunton, that means joint design, primers and backing rod as standard.
Halls, schools and small commercial buildings near places like Hunton have movement joints in brick, block and concrete too. They tend to be overlooked until something leaks or cracks.
Work we carry out comes with a 12-month guarantee. Should something we installed fail, call the office on 01277 525 020 or send details through our quote form and we’ll come back to it.
- Location
- Hunton (ME15)
- Wider area
- Kent
- Cover
- A 12-month guarantee
- Price
- Fixed quote, scope in writing
- Call
- 01277 525 020
- Updated
- 3 November 2026
Towns and villages near Hunton
Also in Hunton
Leave it or put it right?
Some runs only need partial renewal or topping up. Where existing filler is well bonded and the gap beside it is small, a full strip-out isn’t always needed, and we will say which joints need what. For buildings around smaller places like Hunton, water damage can go unnoticed for longer, especially where a building isn’t used daily, so a failed joint can leak for a while before anyone sees it. Resealing early avoids that.
The work involved drives the cost: removing old material, preparing the joints, the product, the access and how the work is phased. Call for a quote and we’ll explain how it’s made up.
What you get with us
- 12-month guarantee on workmanship
- One contact handling all your sites
- CHAS accredited contractor
- Sealing commercial buildings since 2005
Read how commercial sealant jobs are priced and how we’re accredited.
Warehouse floors and decks around Hunton
The South East is one of the drier parts of the UK. External joints still wait for dry conditions, and where de-icing salt is spread in winter, open joints let it in. Hunton is about 31 miles from central London. The roads out of London are lined with trade parks and distribution sheds, and their floor joints take forklift and pallet-truck traffic all day.
A campus such as University for the Creative Arts - Maidstone, 4 miles to the north-east of Hunton, has long runs of movement joint in its buildings, decks and paving. Schools like Hunton Church of England Primary School often have long brick elevations with movement joints that age quietly. Hospitals like Oakwood Hospital (to the north of Hunton) have multi-storey or surface car parks whose joints carry vehicles round the clock.
Hunton is about 4 miles south-west of Maidstone, in Kent. Businesses, contractors and managing agents in Hunton use us for work on floor joints. 931 places across Kent fall within our area, including Hunton. London is covered too, around 31 miles from Hunton.
Work on floor joints is covered throughout ME15. Among the streets we cover are West Street, Bensted Close and Bishop's Lane, and sites on any of them can send details for a fixed quote. Sites close to Hunton are covered too, including Benover (1 mile west), Yalding (1 mile north-west), Congelow (1 mile west), Chainhurst (1 mile south-east) and Laddingford (2 miles west). Further afield, our area takes in Maidstone (4 miles north-east), Sittingbourne (15 miles north-east), Sevenoaks (13 miles west), Royal Tunbridge Wells (10 miles south-west), Gravesend (15 miles north) and Tonbridge (8 miles west).
Around Hunton
In Hunton, that means premises near Quarry Wood, among other places. For rail, the closest station is Yalding station, about 2.1 miles west of the centre. Nearby you’ll also find Teapot Island (1.8 miles west) and Oakwood Hospital (3.7 miles north).
How a job runs
Working in a building that stays open takes some planning. The work area is signed and kept contained, with routes through the building left open and work section by section so the rest of the building stays in use. For a building around Hunton, tell us how to find it and who will meet us. Send that with the details and we’ll confirm the plan with the quote.
- First, the zones and order of work are agreed with you.
- Any joints with broken edges are flagged before work starts.
- We clear each run back to clean concrete.
- The chosen filler or sealant goes in flush with the slab.
- Each area is handed back when ready for traffic.
Preparing the site
- Point out parking and an unloading spot
- Flag any permit to work we will need
- Point out any areas we must not close
Request a quote
To get a fixed quote, phone 01277 525 020 or send photos by email with the site address and an outline of the work. You can also send details through our quote form.
Advice
Site staff or a sealant specialist?
There’s also the paperwork. Main contractors and clients often ask for CSCS cards, RAMS and insurance details, and our CSCS-carded applicators are used to working under those rules.
Putting right a botched joint often costs more than sealing it well at the start, because the whole bead must be removed and the faces cleaned back again. For that reason, many FMs and contractors use a sealant specialist from the outset.
After the work
For the best life from the joints:
- Treat loading bay joints first if they’re failing
- Remind operators to lift rather than drag
- Hold traffic back until the product has cured
- Check joint lines on busy aisles regularly
Walk the main truck routes every few months and look along the joint lines. Watch for filler pulling away from an edge, fresh chipping or grit collecting and keep photographs so changes are easy to compare.
Edges tend to break slowly at first, then quickly. Each chip makes the drop deeper and the next impact harder so early treatment saves a lot of trouble.
FAQs: Hunton
Is Hunton too far out for you?
Not at all: smaller places are covered as well as towns. We work across Greater London and the South East. Send photographs and a list of what needs doing, and we will plan the job to need as few trips as possible.
Would you work within a site like Oakwood Hospital?
Yes. Healthcare sites are among the places we work. We follow the site’s permits, sign-in and infection-control procedures in every area.
How long before trucks can use the joints?
Each product has its own cure time, and cold floors slow it down. Phasing is planned with that in mind.
Does the weather affect the work?
It can, when the joints are outside. Wet joints and cold, damp or frosty conditions stop the sealant bonding properly, so external work may be moved if conditions aren’t right. Internal work is far less affected.
What about RAMS and site documents?
Let us know which documents the site needs, such as RAMS, an insurance certificate or CSCS details, and we’ll confirm them with the quote.
How long do sealant joints last?
There isn’t a single answer, because life depends on how much the joint moves, how exposed it is and how it’s cleaned and used. Regular inspection is the best way to catch problems early.
Which sealant will you use?
The specification comes first, if there is one. If there isn’t one, it comes down to the joint: its movement, its surfaces and what it has to cope with.
Surface by surface
Saw-cut induced joints
Sawn joints make up most of the joint length in a typical industrial floor. We clear them back to clean concrete and fill them to the depth the product calls for, finishing flush with the slab.
Retail and showroom floors
We plan shop-floor work so trading can continue. Give us your opening pattern and access windows and the phasing follows.