Floor Joint Sealing contractors in Hemsted
Planning work on a floor joint in Hemsted? We look at it, seal it with the right product and hand it over with a 12-month guarantee.
- Scruffy, dirty joint lines on a shop or showroom floor
- Loading bay joints breaking down
- Joint fill separating from the concrete
Floor joint sealing near Hemsted
Share the site address and what’s failing, and we’ll reply with a fixed quote or arrange a visit.
Floor joint sealing in Hemsted, done properly
Sometimes the concrete either side of a joint has already spalled. A filler laid against broken edges has nothing sound to grip, so if the edges need repair before any filling, we will say so and leave that decision with you. Most enquiries involve grimy joint lines spoiling a showroom floor and dock area joints that have failed first, across construction joints, joints along racking aisles and saw-cut induced joints. Searching for sealant specialists in Hemsted? Mastic Doctor has worked for contractors, FMs and building owners since 2005.
Jobs around smaller places like Hemsted are planned so the whole job is done in one visit. Note joint widths and the traffic that uses them, and we’ll take it from there.
Every job we finish is backed by a 12-month workmanship guarantee, in Hemsted as everywhere else we work. If a joint we sealed fails because of how it was installed, we come back and put it right.
- Place
- Hemsted (CT18)
- Wider area
- Kent
- Guarantee
- A 12-month guarantee
- Quotes
- A fixed quote before we start
- Telephone
- 01277 525 020
- Page updated
- 3 November 2026
Different surfaces, different methods
Saw-cut induced joints
A sawn joint left open soon packs with debris and chips at the edges. Filled in good time, they stay narrow and neat.
Retail and showroom floors
Polished and coated concrete floors in shops and showrooms show every joint. A flush, neat fill in a suitable colour keeps the floor looking right and confirm which colours the product comes in.
Floors, slabs and movement joints in Hemsted
Hemsted is about 56 miles from central London. Warehousing clusters around the motorways that ring and radiate from London. Hemsted sits in one of the drier corners of the country, the South East. External joints still wait for dry conditions, and where de-icing salt is spread in winter, open joints let it in.
For floors and slabs around Hemsted, the product is chosen for the traffic and the movement at each joint.
Hemsted is about 5 miles north of Hythe, in Kent. We cover commercial sites throughout Hemsted, whether it’s a single job or part of a planned programme. Hemsted is one of 931 places in Kent on our list for floor joints. For work in that direction, see our London page (56 miles or so).
Commercial sites across CT18 are covered for floor joints. We also cover Woodland (1 mile south-east), Skeete (1 mile south), Stowting (1 mile west), Rhodes Minnis (1 mile north-east) and Stowting Common (1 mile north-west). Further afield, our area takes in Ashford (8 miles west), Canterbury (10 miles north), Dover (11 miles east), Folkestone (6 miles south-east), Whitstable (15 miles north) and Faversham (14 miles north-west).
Around Hemsted
The nearest railway station is Westenhanger station, roughly 2.9 miles south. Well-known places in the area include Saltwood Castle (4 miles south) and Elham Valley Countryside Centre And Railway Museum (3.7 miles south-east). Open spaces near Hemsted include Hatch Park and Tolsford Hill.
Diagnose, treat, sign off
We bring the products specified for the job, along with primers and backing rod. Any old material is cut back to clean, sound faces, the manufacturer’s primer is applied where it’s called for, and the sealant is tooled off neatly. Rural sites near Hemsted may need directions, gate codes or a contact on site. Add it to your enquiry and we’ll build it into the plan.
- We look at joint widths, edge condition and the traffic on each route.
- A fixed quote follows, listing the treatment for each area and the order of work.
- Each joint is cleared of old fill and dirt and taken back to clean, sound edges.
- We vacuum each run and prime it if the chosen product requires a primer.
- We fill each joint to depth and finish it flush so wheels roll straight across.
- We tell you when each zone can carry trucks again and move on to the next.
What we need from you
- Send asbestos survey details if the building is pre-2000
- Tell us what induction or permit system the site runs
- Tell us which areas need to stay in use
Request a quote
Send us photos, drawings or a joint schedule are often enough for a fixed quote. Where a site visit makes more sense, we’ll arrange one.
Related advice
General trades versus a specialist
Redoing a failed joint usually costs more than getting it right at the outset, since all of it has to come out and the faces be cleaned back again. That’s why many clients bring in a specialist from the beginning.
A short, simple internal joint is often within reach of a maintenance team. Where it goes wrong is preparation: sealing over old material, sealing onto damp or dusty surfaces, or a product that can’t take the movement.
FAQs: Hemsted
Does a site in Hemsted have to shut while its joints are sealed?
In most cases the site keeps working. Joints are done in phases, a bay, aisle or deck at a time. Tell us which hours and entrances we can use and we will plan from there.
Is Hemsted too small for you to travel to?
Not at all. Hemsted is within our area. Our area covers London and the South East counties. We plan jobs in smaller places so return trips are kept to a minimum.
How do you deal with asbestos in old sealant?
Managing asbestos is the dutyholder’s responsibility, so we will ask for the register before work on an older building. Work pauses if suspect material is found, until it has been tested.
Can you phase floor joint work around operations?
The work is phased. We work aisle by aisle or zone by zone so the rest of the floor stays in use. Tell us your site hours and access windows and we’ll plan around them.
Should floor joints be filled or sealed?
It depends on the traffic and the movement. Forklift routes generally call for a semi-rigid filler that holds the arrises, while joints that move more take a flexible sealant.
What information helps you price floor joint sealing?
A rough joint length, a few photos and a site plan are usually enough for a quick quote. We can visit where that helps, and you can give us a call on 01277 525 020 or email a schedule or drawings to arrange it.
When can forklifts run over new joint filler?
Cure times vary with the product and how cold the slab is. You’ll get a reopening time for each area before we start.
Common problems we fix in Hemsted
Oil, laitance, dust and old cleaning chemicals build up inside joints. If the faces aren’t taken back to clean concrete first, the new material simply lifts out.
Any of the following is a good reason to get the joints checked over:
- Drivers complaining about joints on a route
- Sealant pulled out along a truck route
- Unfilled floor joints collecting dirt and grit
- Cracked and crumbling joint fill
In a school such as Stowting Church of England Primary School, movement joints in brick, block and hall floors tend to be forgotten until they leak.
What your quote should include
- Is the sealant right for the movement and the substrate?
- How they handle RAMS and site documents
- How joint depth will be controlled
- Health and safety accreditation such as CHAS
Building owners, agents and FMs in Hemsted
Blocks and communal areas make up much of the work for housing associations and agents. Work can be phased so residents and staff keep access throughout, and each stage is agreed with your contact.
Main contractors use us as their sealant subcontractor on new-build and refurbishment projects. We work to your programme, your specification and your site rules.
What sets the cost
Your fixed quote is built from the real scope. It allows for:
- Which sealant the job calls for
- Quantities, in metres or numbers
- Travel to remote or island sites
- Whether the work must be split into stages
Whether it’s a single area or a whole estate, the same things set the price: what’s in scope, how we reach it, what’s specified and when it needs doing. Call for a quote, and you will have a fixed figure to work with.
Sending details for a quote
It doesn’t need to be a full survey. A few details are enough to get going:
- Where the site is, with the postcode
- Any dates the work must fit around
- A wide shot and a close-up of the area
- Whether an asbestos survey exists
Specifications, drawings and tender packages are welcome with any enquiry, and we will price against exactly what is specified. Smaller jobs need nothing more than photos and a few notes.