Scotland

Fire Stopping in Argyll and Bute

Fire stopping in all 124 towns and villages of Argyll and Bute, done properly, quoted before any work starts and a 12-month guarantee.

Book fire stopping in Argyll and Bute

Tell us what needs sealing and where, with photos or drawings if you have them, and we’ll price it.

Send your details 01277 525 020

Fire stopping across Argyll and Bute

Fire-rated and intumescent sealing of service penetrations and linear gaps. Pick your town below to see the details for your area, or call or email us for a quote.

Biggest towns in Argyll and Bute

How fire stopping works in Argyll and Bute

Sealant is the specified answer for plenty of openings, such as metal pipes, cables and some small ducts where the detail covers them. Larger openings and some plastic pipes call for collars, wraps, batts or boards instead. We use sealant where it is the specified product, and we tell you when a detail calls for something else. We work on small duct penetrations where the tested detail allows, pipe penetrations and linear gaps at wall heads, and the failures we’re asked to look at most are service penetrations left open after M&E works and penetration schedules that need working through.

A typical day starts with protection: masking tape along the joint edges and sheeting over anything nearby. The work itself usually takes a single visit for a short list of penetrations, or a phased programme for a whole building, and our waste is bagged and taken away as we go.

First we confirm the product and tested details named in the specification.
We sort the openings by the detail each one needs.
Improvised fillers and failed sealant are removed.
Mineral wool or other backing is fitted where required.
We gun the sealant in to the specified depth around each service and tool it.
We walk the completed areas with you and confirm the records agreed at quote stage.

How we quote

The product called for affects the cost, as does the preparation each joint needs, from cutting out to priming and backing rod. Access, phasing and site rules also count.

What you get with us

Our applicators hold CSCS cards
12-month guarantee on workmanship
Over 20 years of commercial sealing
Specification-led, product-correct work

Request a quote

Let us know the site, the scope and your timescale, and we’ll put a fixed quote together. To get it moving, give us a call on 01277 525 020 or send photos by email.

Around Helensburgh

Recent enquiries here include premises near Lomond School, The Henry Bell pub and St Joseph's R.C. Church, among other places. Helensburgh has its own railway station: Helensburgh Central station. A little further out are Ardencaple Castle (1.3 miles west) and Victoria Infirmary (0.5 miles south-east). Green spaces nearby include Lyle Hill.

Fire-resisting walls and floors across Argyll and Bute

Hospitals, schools, care homes, offices and blocks across Argyll and Bute all rely on fire-resisting walls and floors. Where fire-rated sealant is the specified product for a service penetration or linear gap, we install it to the manufacturer’s tested detail.

Our area covers every Scottish council area, Argyll and Bute included. Travel is planned so the work is finished in as few trips as we can. On the coastal side of Argyll and Bute, sea-facing elevations normally show failed joints first.

Helensburgh: In a building such as St Joseph's R.C. Church, any service penetration through a fire-resisting wall should be sealed to the specified detail. At a healthcare site like Victoria Infirmary, 0.5 miles south-east of Helensburgh, new services through compartment walls are a constant, and each needs the specified seal.

What we’re called out for in Argyll and Bute

Head-of-wall joints and wall-to-wall junctions are frequent weak points. Movement in the frame or slab can open the joint. The tested detail for a linear joint states the width and movement it covers.

These are often picked up first by site or facilities staff:

Openings found when ceilings come down for a refit
Head-of-wall gaps with no fire seal
Improvised or mixed-product fire seals
Unsealed openings around new pipes and cables

When to bring in a specialist

What you see is the finished bead, but most of the work is hidden. Backing rod, primer where specified and a joint designed to move with the building are where general trades tend to cut corners.

Paperwork matters too. Main contractors and clients often ask for CSCS cards, RAMS and insurance details, and our CSCS-carded applicators are used to working under those rules.

Surface by surface

Plastic pipes

In a fire, plastic pipework melts away and leaves an opening. Some intumescent sealants are tested on smaller plastic pipes. We check the pipe material and diameter against the detail before we start.

Risers and ceiling voids

Risers and ceiling voids hold most of a building’s service penetrations. Access to these areas is planned with you in advance, including keys, permits and any isolations.

Maintenance after handover

Every sealant joint needs some looking after, and their life depends on movement, exposure, cleaning and use. We suggest:

Keep product data and details in the fire safety file
Keep general-purpose fillers away from compartment walls
Ask which product is in place before decorating
Make fire stopping part of every scope that crosses a fire-resisting wall

Once the seals are in, tell other trades they exist and must not be disturbed. Any seal cut back for a new service needs reinstating to its tested detail using the same product.

Write fire stopping into the scope of any work crossing a compartment wall or floor. Then the seal goes in while the area is open.

Why deal with it now?

An unsealed opening affects more than fire safety: smoke, noise and draughts pass through them every day. Sealing them to the specified detail deals with the fire risk first, and the other benefits follow.

Comparing quotes

How they handle RAMS and site documents
Their approach to joint depth and backing
Their plan for phasing and protecting the area
Who will actually carry out the work

Your questions answered

How long does a typical visit take?

The duration is planned around your programme and the access we’re given. We’ll give you an estimate of time on site when we quote.

Can you follow the specification on our project?

Yes. Include it with the drawings when you ask for a quote, and we will price the work to it, flagging anything that needs clarifying.

What will the job cost?

Each job is quoted on its own details. For yours, speak to us on 01277 525 020 or use the quote form.

Can you handle several sites?

Yes. We take on portfolio and planned maintenance work, planned site by site to suit how each building is used.

What’s the quickest route to a quote?

It works in four steps: send details, receive a fixed quote, we carry out the work, and it’s guaranteed. The first step only needs photographs and a postcode.

Will you just go over the old sealant?

No. Sealing over old material is one of the classic causes of early joint failure, so it all comes out first.

Is sealant suitable for all service openings?

No. Each fire-rated sealant is tested for particular services, gap sizes and substrates. Outside that, a different product is needed, specified by your designer.