Fire stopping in Bowmore
Need fire stopping in Bowmore? It’s simple: send details, get a quote, we seal, guaranteed.
- Openings left by services added after handover
- Seals that don’t match their tested detail
- Damaged fire seals in risers and voids
Fire stopping in Bowmore
Tell us what needs sealing and where, with photos or drawings if you have them, and we’ll price it.
Aftercare for building managers
For the best life from the joints:
- Don’t let anyone top up a fire seal with the wrong product
- Check risers and ceiling voids after each round of works
- Treat an open penetration as a priority repair
- Get seals inspected before ceilings and boxing close
Never top up a fire seal with foam, ordinary silicone or filler. A repair should use the original product, installed the same way.
Specify fire stopping early on refits, not as an afterthought. The designer can then choose details that suit the services planned, and installation follows the programme.
Fire stopping in Bowmore
Most of our fire stopping work happens after the building is up. Each new cable, pipe or data route cut through a fire-resisting wall leaves an opening behind. Those on your schedule are closed with the specified product. If you have fire sealant pulled out of the opening and non-fire-rated filler around services, we can help. Sealant contractors, mastic applicators, sealant specialists: whatever the job title on the order, in Bowmore it comes down to the same thing: the right product in a properly prepared joint.
Hotels and care homes around smaller places like Bowmore often have services added during refurbishment. We fit the specified fire-rated sealant as its published detail shows and raise it if another product is needed.
Every job ends the same way: guaranteed. You get a 12-month guarantee on our workmanship, and the quote explains what it covers.
- Where
- Bowmore (PA43)
- Region
- Argyll and Bute
- Cover
- 12 months on our workmanship
- Price
- A fixed quote before we start
- Telephone
- 01277 525 020
- Updated
- 3 November 2026
Towns and villages near Bowmore
What else we do in Bowmore
When to call us in Bowmore
Damage plays a part too. Seals get knocked during maintenance, cut back to add a cable or pulled out when services are swapped.
These are often picked up first by site or facilities staff:
- Unsealed openings around new pipes and cables
- Fire-rated sealant that has cracked or shrunk back
- Expanding foam used as fire stopping
- Seals that don’t match their tested detail
For a hotel such as Bowmore Hotel, under half a mile to the west of Bowmore, penetration seals are worth checking after any refit or services upgrade.
What your quote should include
- Whether their applicators hold CSCS cards
- The terms of the workmanship guarantee
- What site paperwork they can supply
- Whether primer will be used where the manufacturer specifies it
Compartment walls and floors in Bowmore
Bowmore has a number of hotels close by, all within 2 miles. A hotel refit often runs new services through compartment walls between bedrooms and corridors, and each opening needs the specified seal. Under the Scottish non-domestic Technical Handbook, clause 2.1.14, penetrations should be fire stopped to at least the wall or floor’s fire resistance duration, with proprietary products, intumescent ones included, tested for their end use. Our part is installing the specified fire-rated sealant to its tested detail.
On a hospital site such as Islay Hospital, less than half a mile to the east of Bowmore, fire-rated sealant goes in where the specification calls for it, with the work planned around the estates team’s permits.
Bowmore (Gaelic: Bogh Mòr) is in Argyll and Bute. Our applicators travel to Bowmore for work on service penetrations. 124 places across Argyll and Bute fall within our area, Bowmore among them. Sites around Glasgow have their own page, roughly 78 miles from Bowmore.
We cover the PA43 postcode districts for service penetrations. Streets here include High Street, Main Street and The Square, and sites on any of them can send details for a fixed quote. Just outside Bowmore, we also work in Port Charlotte (4 miles west), Keills (8 miles north-east), Imeraval (9 miles south), Port Askaig (9 miles north-east) and Port Ellen (10 miles south-east). Island and remote sites need extra planning, with travel, ferry crossings where needed and weather to allow for, so give the site location in your enquiry.
What’s near Bowmore
Other landmarks nearby include Islay Hospital (less than half a mile east) and Museum of Islay Life (3.8 miles west). Open spaces near Bowmore include Loch Skerrols.
Why deal with it now?
A seal that doesn’t match its tested detail gives false comfort. Correcting it means cutting it out and starting again with the specified product, so it makes sense to get it right first time. Renewing every failing joint on one visit is the sensible approach for a place like Bowmore. Photos of each area help us quote the whole job.
The price depends on how many linear metres there are, how much old material needs removing and how the joints are reached. Call for a quote once you have the details.
What you get with us
- 12-month guarantee on workmanship
- One number for every site we cover
- Work carried out by CSCS-carded applicators
- Old sealant cut out, never sealed over
Read how commercial sealant jobs are priced and how we’re accredited.
How the job changes by surface
Risers and ceiling voids
Voids hide a lot of unsealed openings. We work through the areas on your schedule methodically.
Masonry and concrete
Openings through concrete vary from tidy cores to rough break-outs. The gap is measured at the widest point against the detail’s limits, and any that don’t are flagged.
Our process
Site rules come first: sign-in, induction and whatever permit system the building uses. Once we are cleared to begin, we take the joints in the sequence agreed with you. Tell us who will meet us and how to get in at your building near Bowmore. That goes into the plan alongside the quote.
- First we go through the drawings, schedule or specification for the seals.
- On site, each opening is checked against the tested detail it is meant to follow.
- Anything that doesn’t belong in the opening, such as expanding foam or general-purpose filler, is removed.
- We fit the backing the detail asks for, to the stated depth.
- We apply the specified sealant to the depth and around the services as the detail shows.
- Openings that need a collar, wrap, batt or other product are flagged to you rather than filled with sealant.
Getting the site ready
- Move anything stored against the joints
- Confirm the product named in the specification
- Let us know about inductions and permits
Request a quote
Pricing a project or setting a maintenance budget? Send the scope and any drawings, and we will return a fixed quote you can plan around. For a chat about it beforehand, call the office on 01277 525 020 or email us.
Related advice
Bowmore: questions and answers
Is a smaller place like Bowmore outside your area?
Not at all: smaller places are covered as well as towns. Our area covers all of Scotland, cities, towns and islands alike. Good photographs up front let us bring everything on the first visit.
Would you work within a site like Islay Hospital?
Yes. We work in healthcare settings as well as offices and schools. The estates team’s permit system and infection-control rules come first, and the work is planned around them.
Can you send site paperwork?
Tell us what site paperwork you need (RAMS, insurance certificate, CSCS details) and we’ll confirm with the quote.
How long will the new sealant last?
There’s no fixed lifespan: movement, exposure, cleaning, traffic and the product all play a part. Treat them as maintenance items and inspect them regularly.
Do you have third-party installer accreditation for fire stopping?
No, and we’d rather be clear about that. Third-party schemes aren’t a legal requirement, but many clients and main contractors ask for them, so it’s worth checking what your contract says. Where it isn’t required, we install the specified sealant to the maker’s details.
Can one quote cover more than one building?
Yes. We take on portfolio and planned maintenance work, with each site phased to suit its occupants.
Can you work to our specification?
Yes. We follow the specification, along with the manufacturer’s installation guidance.
Doing it in-house
Redoing a failed joint normally costs more than getting it right at the outset, because the whole bead must be removed and the faces cleaned back again. That’s why many clients bring in a specialist from the beginning.
Site maintenance staff can often handle a short internal joint. Where it goes wrong is preparation: sealing over old material, sealing onto damp or dusty surfaces, or a product that can’t take the movement.