Fire Stopping in Ellenabeich
Fire stopping for Ellenabeich, from a contractor working since 2005. Fully insured, with a 12-month guarantee.
- Builders’ foam or ordinary silicone in compartment walls
- Fire-stopping items raised at inspection or handover
- Openings left by services added after handover
Need fire stopping in Ellenabeich?
Share the site address and what’s failing, and we’ll reply with a fixed quote or arrange a visit.
When it isn’t the sealant
Part of a good diagnosis is knowing where sealant stops. You’ll hear from us if the cause turns out to be one of these:
- Designing or specifying fire stopping, which sits with the designer or fire engineer
- Fire doors, dampers or other fire safety equipment
- Large openings beyond what any sealant detail covers
If in doubt, phone 01277 525 020 or use the quote form and we’ll say what we think before you book.
Surfaces we seal
- Linear gaps at wall heads
- Joints between fire-resisting walls and floors
- Service gaps in risers
- Small duct penetrations where the tested detail allows
- Pipe penetrations
- Cable penetrations
About our fire stopping in Ellenabeich
Every service that crosses a compartment wall or floor leaves an opening, and that opening needs sealing to hold back fire and smoke. Our part is installing fire-rated and intumescent sealant at those openings and along linear gaps, where the specification calls for it. Each seal follows the manufacturer’s tested detail, not a rule of thumb. Site teams most often ask us about expanding foam used as fire stopping and open linear gaps along the top of fire-resisting walls, across pipe penetrations, linear gaps at wall heads and service gaps in risers. Looking for mastic applicators who cover Ellenabeich? We have been sealing commercial buildings since 2005.
For a building near Ellenabeich, we plan fire-rated sealing so it’s finished in one visit where possible. Send the specification and photographs of the openings, with sizes if you have them.
We stand by our work: 12 months, guaranteed. That covers our preparation and application, and if something we did falls short, we return to it.
- Place
- Ellenabeich (PA34)
- Region
- Argyll and Bute
- Cover
- A 12-month guarantee
- Quote
- A fixed quote before we start
- Telephone
- 01277 525 020
- Updated
- 3 November 2026
How the job changes by surface
Plastic pipes
Plastic waste pipes through slabs come up often. Whether sealant alone is acceptable depends entirely on the tested detail.
Masonry and concrete
Openings through concrete vary from tidy cores to rough break-outs. The gap is measured at the widest point against the detail’s limits.
Why deal with it now?
A seal that doesn’t match its tested detail gives false comfort. The fix is to remove it and reinstall to the detail, so it makes sense to get it right first time. Around smaller places like Ellenabeich, halls, stores and seasonal buildings may not be checked often, so a failed joint has time to cause damage. Resealing early avoids that.
The specified product makes a difference, and so does the preparation. Access, phasing and site requirements come into it too.
Why us?
- Work carried out by CSCS-carded applicators
- Over 20 years of commercial sealing
- Failed material removed, not covered up
- Fully insured
Take a look at our cost guide and how we’re accredited.
How a job runs
A typical day starts with protection: masking tape along the joint edges and sheeting over anything nearby. The work itself typically takes longer where risers, ceiling voids or occupied floors have to be worked through in sequence, and our waste is bagged and taken away as we go. Travel to smaller Scottish places like Ellenabeich is planned so the job is finished in one visit where possible, so photographs, sizes and a full list matter. External joints need a dry spell as well.
- First we confirm the product and tested details named in the specification.
- We sort the openings by the detail each one needs.
- Old or wrong materials are cut out.
- Where the detail needs backing, it goes in at the stated depth.
- We gun the sealant in to the specified depth around each service and tool it.
- We walk the completed areas with you and confirm the records agreed at quote stage.
Before we start on site
- Warn occupants and staff about the work
- Tell us which areas need to stay in use
- Send any specification or drawings in advance
Quotes
Send details, get a quote, we seal, guaranteed: that’s how every job runs. The first step is to ring 01277 525 020 or send details through our quote form with what you know.
Related advice
Fire stopping around Ellenabeich: points for this area
In Scotland, clause 2.1.14 of the non-domestic Technical Handbook expects service penetrations to keep at least the fire resistance duration of the wall or floor, with proprietary products, intumescent ones included, tested for their end use. Our part is installing the specified fire-rated sealant to its tested detail.
Buildings near Ellenabeich get the fire-rated product that’s specified, installed to its tested detail. For a building such as Tin Church, new heating or data runs are the usual reason penetrations need sealing.
Ellenabeich is about 40 miles north-west of Helensburgh, in Argyll and Bute. If you are looking for fire stopping in Ellenabeich, we can help, as we do across Argyll and Bute. 124 places across Argyll and Bute fall within our area, Ellenabeich among them. We also cover Glasgow, some 60 miles away.
We cover the PA34 postcode districts for service penetrations. Nearby places we also cover include Clachan Seil (2 miles north-east), Craobh Haven (6 miles south-east), Kilmelford (6 miles east), Barravullin (7 miles south-east) and Ardfern (9 miles south-east). Further afield, our area takes in Oban (10 miles north-east), Dunollie (11 miles north-east) and Dunbeg (13 miles north-east). For island and remote sites, travel and materials need planning ahead, so include the location in your enquiry.
Local landmarks in Ellenabeich
Nearby you’ll also find Slate Islands Heritage Trust Museum (0.7 miles north-west) and Ardfad Castle (2 miles north-east). For a walk, there’s Ballachuan Loch.
Nearby places to Ellenabeich
Other services in Ellenabeich
When to bring in a specialist
Some joints are best left to specialists: for instance fire-rated seals that must match a tested detail, trafficked floor joints and external movement joints. Getting these wrong typically costs more in the end than doing them right.
Using site staff can make sense for a small touch-up, but anything bigger is another matter: a specialist works through quantities efficiently, leaves a consistent finish and backs it with a 12-month guarantee.
Owners, agents and contractors
We work for building owners and managing agents on everything from one building to a spread of sites around Ellenabeich. One quote can cover more than one site, so there’s one set of paperwork to deal with.
As a CHAS accredited contractor and Constructionline member, we are straightforward to vet for your supplier list. We are fully insured, and our insurance certificate can go with the quote.
Your questions answered
Do you design the fire stopping for buildings in Ellenabeich?
No. Fire-stopping design and sign-off belong to the designer, principal designer, fire engineer or building control. Our part is installing the specified product to its tested detail, and telling you if the detail calls for something other than sealant.
Which Scottish guidance covers penetration seals in Ellenabeich?
The non-domestic Technical Handbook, clause 2.1.14, expects a penetration to keep at least the wall or floor’s fire resistance period, with proprietary products tested for the use they’re put to. Design sits with the designer and the verifier; installation to the tested detail is our part.
Can you work while the building is occupied?
Yes, with some planning. Tell us your site hours and access windows and we will plan around them.
Can you send site paperwork?
Requirements differ from site to site, so tell us what you need and we’ll confirm it when we quote.
What will the job cost?
That depends on the job: quantities, access, the product and any phasing. Call for a fixed quote.
When is resealing likely to be due?
There isn’t a single answer, because life depends on how much the joint moves, how exposed it is and how it’s cleaned and used. Regular inspection is the best way to catch problems early.
Is colour matching possible?
In many cases, yes. Sealants are made in a wide range of standard colours, and matching to RAL references or nearby finishes is commonly requested. We’ll confirm the colours available for the specified product.