Fire stopping in Kilmelford
Fire-rated and intumescent sealing of service penetrations and linear gaps in Kilmelford and across Argyll and Bute. CHAS accredited and fully insured, with a 12-month guarantee.
- Seals that don’t match their tested detail
- Penetration schedules that need working through
- Expanding foam used as fire stopping
Fire stopping near Kilmelford
Send drawings, photos or a joint schedule, or tell us about the site, and we’ll come back with a fixed quote.
Questions we are asked in Kilmelford
Do you decide the fire-stopping details for buildings in Kilmelford?
No. The designer or fire engineer sets the detail and building control accepts it. We install fire-rated and intumescent sealant around service penetrations and linear gaps where it is specified, to the manufacturer’s tested detail.
Is Kilmelford too far out for you?
Not at all. Kilmelford is within our area. We cover the whole of Scotland. Good photographs up front let us bring everything on the first visit.
Do you need to see the site first?
Many jobs can be quoted from photographs, drawings or a joint schedule. If the job needs a look first, we will arrange a visit before quoting.
Can you fit around our working hours?
Mention the site’s hours and access windows in your enquiry, and we’ll schedule the work to suit. Our office runs Monday to Friday, 8am until 5pm.
How long does a job like this take?
That varies with the scale of the job, but the work typically takes a single visit for a short list of penetrations, or a phased programme for a whole building. For bigger or phased jobs, we will set out a timescale with the quote.
Do you take on small jobs?
We quote for single jobs as well as large packages and programmes. Send details for a fixed quote.
When can the area be used after sealing?
We’ll confirm how long the chosen product needs to cure, and sign any area that should be left alone.
Fire stopping in Kilmelford
It helps to set out our role at the start. The designer, fire engineer or building control decides which fire stopping is required. What we bring is careful installation of the specified sealant, to the maker’s guidance on buildings around Kilmelford. Most enquiries involve seals that don’t match their tested detail and unsealed joints where partitions meet the slab, across small duct penetrations where the tested detail allows, linear gaps at wall heads and joints between fire-resisting walls and floors. Searching for sealant specialists in Kilmelford? We’ve been sealing commercial buildings since 2005.
For a building near Kilmelford, we plan fire-rated sealing so it’s finished in one visit where possible. Photos of the gaps, the services and the wall or floor type help us bring the right products.
Our 12-month guarantee is about workmanship, not wear and tear. How long a sealant joint lasts depends on movement, exposure, cleaning and use, so we are clear about what is covered before work starts.
- Place
- Kilmelford (PA34)
- Region
- Argyll and Bute
- Guarantee
- 12 months on our workmanship
- Quote
- Quoted before any work starts
- Telephone
- 01277 525 020
- Page updated
- 3 November 2026
Building owners, agents and FMs in Kilmelford
FMs need a contractor who is easy to get on site. Tell us what site paperwork you need, such as RAMS, an insurance certificate or CSCS details, and we will confirm with the quote.
As a CHAS accredited contractor and Constructionline member, we are straightforward to vet for your supplier list. We’re fully insured, and our insurance certificate can go with the quote.
When it isn’t the sealant
Our job is the joint, not everything around it. Sealant alone won’t deal with:
- Plastic pipes whose detail calls for a collar or wrap
- Writing the fire-stopping specification
- Signing off or certifying a building’s fire stopping
If in doubt, phone 01277 525 020 or email us and we’ll say what we think before you book.
Where we work in Kilmelford
- Linear gaps at wall heads
- Pipe penetrations
- Cable penetrations
- Joints between fire-resisting walls and floors
- Small duct penetrations where the tested detail allows
- Service gaps in risers
After the work
Keep the joints in good shape with a few simple steps:
- Report damaged or disturbed seals as soon as they’re spotted
- Ask which product is in place before decorating
- File the specified details where the next contractor can find them
- Check risers and ceiling voids after each round of works
After every round of M&E works, check that the openings created have been sealed. Building it into each contractor’s sign-off keeps the walls intact.
Ask every contractor who works in risers or voids to report openings they create. Small habits like this stop openings building up.
On site: what to expect
Inspect, seal, sign off: that’s the shape of every visit. First comes an inspection and agreement on scope, then we prepare and seal each joint with the specified product, and we finish with a walk round so the work can be signed off. Jobs near Kilmelford are often grouped with others in the same area, to make the most of each trip. Let us know if your dates have any give.
- We read the specification, drawings or penetration schedule you send.
- Every penetration is compared with its detail: wall or floor type, service, gap size and depth.
- Unsuitable fillers and loose debris are taken out of each opening.
- We fit the backing the detail asks for, to the stated depth.
- Fire-rated or intumescent sealant is gunned in to the specified depth, then tooled.
- If an opening needs something other than sealant, we tell you instead of improvising.
Preparing the site
- Point out any areas we must not close
- For older buildings, check the asbestos register before work
- Move anything stored against the joints
Request a quote
Every job follows the same four steps: send details, get a quote, we seal, guaranteed. The first step is to call 01277 525 020 or email drawings and photos with what you know.
Related advice
Fire stopping around Kilmelford: points for this area
In Scotland, clause 2.1.14 of the non-domestic Technical Handbook expects service penetrations to keep at least the fire resistance duration of the wall or floor, using products tested for the way they’re used. We install fire-rated sealant to that tested detail where it is specified.
In a building such as Kilmelford Parish Church, any service penetration through a fire-resisting wall should be sealed to the specified detail. Hotels like The Cuilfail Hotel, less than half a mile north-east of Kilmelford, are refurbished in phases, and each phase can open up compartment walls.
Kilmelford is about 34 miles north-west of Helensburgh, in Argyll and Bute. Businesses, contractors and managing agents in Kilmelford use us for work on service penetrations, as part of our coverage of Argyll and Bute. Our Argyll and Bute coverage takes in 124 places, large and small. Sites around Glasgow have their own page, about 54 miles away.
If you need fire stopping in PA34, the process matches everywhere else we work: send details, get a quote, we seal, guaranteed. We also cover Barravullin (4 miles south-west), Craobh Haven (4 miles south-west), Clachan Seil (6 miles north-west), Ardfern (6 miles south-west) and Ellenabeich (6 miles west) for service penetrations. A short drive away, we cover Oban (11 miles north), Ceann Loch Gilb (15 miles south), Lochgilphead (15 miles south), Dunollie (11 miles north), Dunbeg (13 miles north) and Inbhir Aora (15 miles east). For island and remote sites, travel and materials need planning ahead, so the full address helps from the start.
Near you in Kilmelford
Other landmarks nearby include Caisteal na Nighinn Ruaidhe (4.3 miles east). The countryside around Kilmelford includes Loch a' Phearsain and Càrn Dearg.
Should maintenance staff do it?
Redoing a failed joint usually costs more than getting it right at the outset, because the whole bead must be removed and the faces cleaned back again. For that reason, many FMs and contractors use a sealant specialist from the outset.
General builders and handymen seal joints, but it isn’t their main trade. A specialist prepares properly, controls joint depth and picks a product with the right movement class.
Why deal with it now?
An improvised seal can look finished while offering no tested performance. The fix is to remove it and reinstall to the detail, and doing it once, properly, is cheaper. Exposed buildings in Scotland take a lot of weather, so it’s worth renewing joints around Kilmelford before they leak.
The price depends on how many linear metres there are, what has to come out first and the access. Call for a quote when you’re ready.
Why appoint us
- Specification-led, product-correct work
- Health and safety: CHAS accredited
- One contact handling all your sites
- Constructionline member for supplier checks
See what affects the cost and our accreditations and insurance.