Port Askaig fire stopping
Fire-rated and intumescent sealing of service penetrations and linear gaps in Port Askaig and across Argyll and Bute. CHAS accredited, Constructionline member, with a 12-month guarantee on workmanship.
- Unsealed penetrations discovered above suspended ceilings
- Snag lists that include open service penetrations
- Builders’ foam or ordinary silicone in compartment walls
Fire stopping across Port Askaig
Send drawings, photos or a joint schedule, or tell us about the site, and we’ll come back with a fixed quote.
Fire stopping in Port Askaig: the local picture
Scottish guidance (non-domestic Technical Handbook, clause 2.1.14) asks that penetrations match at least the fire resistance period of the element they pass through, and products should be tested for their end use. Our part is installing the specified fire-rated sealant to its tested detail.
For a hotel such as Port Askaig Hotel, less than half a mile east of Port Askaig, penetration seals are worth checking after any refit or services upgrade.
Port Askaig (Gaelic: Port Asgaig) is in Argyll and Bute. We cover Port Askaig and the rest of Argyll and Bute, with the same fixed quotes and 12-month guarantee as everywhere else. 124 places across Argyll and Bute fall within our area, Port Askaig among them. Glasgow is covered too, around 71 miles from Port Askaig.
We cover the PA46 postcode districts for service penetrations. Nearby places we also cover include Keills (1 mile south-west), Bunnahabhain (2 miles north), Craighouse (6 miles east), Bowmore (9 miles south-west) and Port Charlotte (13 miles south-west). Island and remote sites need extra planning, with travel, ferry crossings where needed and weather to allow for, so give the site location in your enquiry.
Landmarks near Port Askaig
A little further out are Finlaggan Castle (2.6 miles west). The countryside around Port Askaig includes Beinn Dubh and Ardnahoe Loch.
Fire stopping in Port Askaig
Most of our fire stopping work happens after the building is up. Each new cable, pipe or data route cut through a fire-resisting wall leaves an opening behind. We close the openings listed on your schedule, using the specified sealant and detail. If you’re dealing with fire sealant pulled out of the opening and builders’ foam or ordinary silicone in compartment walls, we can help, on small duct penetrations where the tested detail allows, service gaps in risers and cable penetrations alike. Sealant applicators who only do sealant are a different proposition from a general trade with a gun in the van: in Port Askaig, that means joint design, primers and backing rod as standard.
In smaller Scottish places like Port Askaig, buildings with fire-resisting walls typically include schools, care homes, hotels and health centres. Where services pass through, specified fire-rated sealant is installed following the manufacturer’s guidance for that wall or floor.
We stand by our work: 12 months, guaranteed. It covers how we prepared and applied the sealant, and we come back if anything isn’t right.
- Place
- Port Askaig (PA46)
- Region
- Argyll and Bute
- Cover
- 12 months on our workmanship
- Quotes
- Fixed quote, scope in writing
- Telephone
- 01277 525 020
- Page updated
- 3 November 2026
How the quote is worked out
Quotes vary with the job. It mainly depends on:
- How much there is to seal
- The product specified
- The size and state of each joint
- Any access equipment needed
The product called for affects the cost, as does the preparation each joint needs, such as cutting out, priming or new backing rod. Access, phasing and site requirements come into it too.
What to include in your enquiry
Whether it’s one area or a whole building, these details speed things up:
- Any dates the work must fit around
- Anything awkward about access or site hours
- The asbestos register, for older buildings
- Where the site is, with the postcode
Need a figure for a tender or a budget? We’ll quote against your scope and drawings that you can work with. For a chat about it beforehand, phone 01277 525 020 or email us.
When to call us in Port Askaig
Physical damage is another reason seals stop doing their job. Maintenance work can knock a seal, cut it back for an extra cable or remove it with an old pipe, and the repair is often skipped.
These are often picked up first by site or facilities staff:
- Fire sealant pulled out of the opening
- Fire seals cut back for extra cables and never reinstated
- Open linear gaps along the top of fire-resisting walls
- Expanding foam used as fire stopping
Around Port Askaig, we install fire-rated and intumescent sealant to the product’s tested detail wherever it is the specified product.
What to look for in a quote
- Are they CHAS accredited or on Constructionline?
- The named product and why it was chosen
- How they handle RAMS and site documents
- What the guarantee covers, and for how long
Keeping the joints sound
Sealant joints are maintenance items, and their life depends on movement, exposure, cleaning and use. We suggest:
- Report damaged or disturbed seals as soon as they’re spotted
- Don’t let anyone top up a fire seal with the wrong product
- Ask the designer to confirm details early on refits
- Brief every trade that openings they make must be sealed
Allow the manufacturer’s stated cure time before boxing in or decorating. Not every fire-rated product can be painted, and the data sheet says which.
Specify fire stopping early on refits, not as an afterthought. The designer can then choose details that suit the services planned.
Common questions from Port Askaig clients
Can you produce the fire-stopping design for a job in Port Askaig?
No. Fire-stopping design and sign-off belong to the designer, principal designer, fire engineer or building control. Our part is installing the specified product to its tested detail, and telling you if the detail calls for something other than sealant.
Is Port Askaig too far out for you?
Not at all: smaller places are covered as well as towns. We work across every Scottish council area. Good photographs up front let us bring everything on the first visit.
How do you choose the sealant?
The specification comes first, if there is one. If there isn’t one, it comes down to the joint: its movement, its surfaces and what it has to cope with.
How long does a typical visit take?
It depends on the scope, though a typical visit usually takes longer where risers, ceiling voids or occupied floors have to be worked through in sequence. Larger or phased jobs take longer, and we’ll give you a timescale with the quote.
Will you come and look before quoting?
Many jobs can be quoted from photographs, drawings or a joint schedule. Where they aren’t, we arrange a site visit before quoting.
What will the job cost?
That depends on the job: the volume of work, the access, the specified product and how it’s phased. Call for a quote.
Can you handle several sites?
Yes. A group of buildings can go on one quote, and you deal with one contact throughout.
Honest limits
We seal joints; we don’t mend everything behind them. Sealant alone won’t deal with:
- Issuing fire ratings or certificates for seals
- Gaps in walls that were never built as compartment walls
- Deciding what a wall or floor needs, which belongs to the designer
Not sure which it is? You can speak to us on 01277 525 020 or email a schedule or drawings and we’ll tell you honestly before you book.
Where we work in Port Askaig
- Cable penetrations
- Pipe penetrations
- Joints between fire-resisting walls and floors
- Small duct penetrations where the tested detail allows
- Service gaps in risers
- Linear gaps at wall heads
Also near Port Askaig
What else we do in Port Askaig
Owners, agents and contractors
CHAS accredited and a Constructionline member, we make supplier vetting simple. Our insurance certificate can be sent along with the quote.
Agents, factors and owners’ representatives all follow the same route: send details, get a fixed quote, we seal, guaranteed. Keys, access and contacts can be agreed in advance.
Diagnose, treat, sign off
Working in a building that stays open takes some planning. We sign and contain the area we are in, with routes through the building left open and work section by section so the rest of the building stays in use. Travel to smaller Scottish places like Port Askaig is planned so the job is finished in one visit where possible, so photos, sizes and a full list matter. External joints need a dry spell as well.
- We start with your penetration schedule, drawings or specification.
- Access, permits and the order of areas are agreed with the site team.
- Each opening is checked for wall or floor type, service, gap and depth.
- Unsuitable material is removed and the opening cleaned.
- The specified backing and sealant go in to depth and are finished neatly.
- Anything outside the detail is reported to you rather than sealed.
Getting the site ready
- Move anything stored against the joints
- Agree which areas must stay open
- Point out parking and an unloading spot
Get a fixed quote
Send us photos, drawings or a joint schedule are often enough for a fixed quote. If the job needs a look first, we will arrange a site visit.