Fire Stopping in Hunters Quay
Fire-rated and intumescent sealing of service penetrations and linear gaps across Hunters Quay, carried out by CSCS-carded applicators. Fully insured and CHAS accredited.
- Improvised or mixed-product fire seals
- Openings left by services added after handover
- Seals disturbed by maintenance and left open
Fire stopping for Hunters Quay sites
Share the site address and what’s failing, and we’ll reply with a fixed quote or arrange a visit.
About our fire stopping in Hunters Quay
Most of our fire stopping work happens after the building is up. Each new cable, pipe or data route cut through a fire-resisting wall leaves an opening behind, often unnoticed. Those on your schedule are closed with the specified product. We work on small duct penetrations where the tested detail allows, service gaps in risers and joints between fire-resisting walls and floors, and what we are called in for most is non-fire-rated filler around services and damaged fire seals in risers and voids. For commercial sealant work in Hunters Quay, you deal with one contact from quote to sign-off, for single jobs and planned programmes alike.
Hotels and care homes around smaller places like Hunters Quay often have services added during refurbishment. A round of checks after M&E work is good practice, and any gaps found are sealed where fire-rated sealant is specified.
Every job we finish is backed by a 12-month workmanship guarantee, in Hunters Quay as everywhere else we work. If a joint we sealed fails because of how it was installed, we come back and put it right.
- Location
- Hunters Quay (PA23)
- Wider area
- Argyll and Bute
- Cover
- 12 months on every job
- Quote
- A fixed quote before we start
- Call
- 01277 525 020
- Page updated
- 3 November 2026
When to bring in a specialist
For a quick touch-up, site staff may be fine, but larger jobs are different: a specialist works through quantities efficiently, leaves a consistent finish and backs it with a 12-month guarantee.
Site maintenance staff can often handle a short internal joint. Where it goes wrong is preparation: sealing over old material, sealing onto damp or dusty surfaces, or a product that can’t take the movement.
On site: what to expect
At the end of each section, we remove the tape, clean down and inspect every joint, ready for your sign-off. Where the sealant needs time to cure before use, we tell you and sign the area. For a building near Hunters Quay, directions, keys and a contact on the day are worth sorting early. That goes into the plan alongside the quote.
- We start with your penetration schedule, drawings or specification.
- We plan the sequence of floors, risers and voids with you.
- We compare every service penetration with its tested detail before sealing.
- Unsuitable material is removed and the opening cleaned.
- The specified backing and sealant go in to depth and are finished neatly.
- We tell you about openings that need a different product.
What we need from you
- Share your working hours and any access restrictions
- Warn occupants and staff about the work
- Let us know about inductions and permits
Quotes
Quotes are fixed against the scope you send, so you know the figure before anyone is on site. To ask for one, ring 01277 525 020 or email drawings and photos.
Advice
After the work
Every sealant joint needs some looking after, and how long they last depends on how they’re treated. We suggest:
- Check with the data sheet before painting over fire sealant
- Settle who seals which penetrations at the start of a project
- Have penetrations checked while they can still be seen
- Check risers and ceiling voids after each round of works
New services after handover are a common way fire stopping gets breached. Building it into each contractor’s sign-off keeps the walls intact.
Specify fire stopping early on refits, not as an afterthought. Details can then be picked to suit the actual pipes, cables and ducts, and installation follows the programme.
Penetration seals near Hunters Quay
Scottish guidance (non-domestic Technical Handbook, clause 2.1.14) asks that penetrations match at least the fire resistance period of the element they pass through, with proprietary products, intumescent ones included, tested for their end use. We install what’s specified, to the product’s tested detail. A 2-mile radius around Hunters Quay takes in plenty of hotels. Hotels are divided into compartments, and refurbishments that add pipes and cables through bedroom and corridor walls leave gaps to close.
At a healthcare site like Cowal Community Hospital, 1.2 miles south-west of Hunters Quay, new services through compartment walls are a constant, and each needs the specified seal. Hotels like Ardenslate House Hotel, less than half a mile west of Hunters Quay, are refurbished in phases, and each phase can open up compartment walls.
Hunters Quay is about 3 miles west of Gourock, in Argyll and Bute. We cover Hunters Quay, with the same fixed quotes and 12-month guarantee as everywhere else. Hunters Quay is one of 124 places in Argyll and Bute on our list. Our Glasgow page has more on work in that area, about 25 miles away.
Commercial sites across PA23 are covered for service penetrations. Sites close to Hunters Quay are covered too, including Kirn (1 mile south-west), Dunoon (1 mile south-west), Strone (1 mile north), Sandbank (2 miles north-west) and Kilmun (3 miles north-west). Further afield, our area takes in Helensburgh (7 miles east), Rothesay (11 miles south-west), Cardross (10 miles east), Rhu (6 miles north-east), Garelochhead (9 miles north) and Port Bannatyne (10 miles south-west). Where a site is remote or on an island, travel and materials need planning ahead, so the full address helps from the start.
Landmarks near Hunters Quay
Around Hunters Quay, our work takes us to commercial buildings near Dunoon Grammar School and the streets around them. The nearest railway station is Gourock station, roughly 3.3 miles east of the centre. Nearby you’ll also find Dunoon Castle (1.7 miles south-west) and Cowal Community Hospital (1.2 miles south-west). For a walk, there’s Loch Loskin and Lyle Hill.
Why it’s worth doing now in Hunters Quay
Fire stopping is a regular point raised at inspections and handover. Late discoveries can delay handover while openings are reopened and resealed which is why earlier is better. Buildings that aren’t in daily use, such as halls and seasonal premises, may let water in unnoticed, giving water time to get in. Resealing early avoids that.
What a job costs comes down to the quantity of joints, what has to come out first and how the joints are reached. Call for a fixed quote when you’re ready.
Why clients in Hunters Quay choose us
- Constructionline member for supplier checks
- Clear, fixed quotes
- Sealing commercial buildings since 2005
- One contact handling all your sites
See our cost guide and our accreditations.
When to call us in Hunters Quay
Plenty of openings were simply never closed, often hidden above suspended ceilings or behind boxing. They come to light during inspections, refits or when another trade lifts a tile.
Site and facilities staff are often the first to spot these:
- Seals disturbed by maintenance and left open
- Openings found when ceilings come down for a refit
- Service penetrations left open after M&E works
- Non-fire-rated filler around services
In a building such as Kirn Church, any service penetration through a fire-resisting wall should be sealed to the specified detail.
Comparing quotes
- What site paperwork they can supply
- Health and safety accreditation such as CHAS
- How the joint faces will be prepared and primed
- Their plan for phasing and protecting the area
When it isn’t the sealant
Part of a good diagnosis is knowing where sealant stops. You will hear from us if the cause turns out to be one of these:
- Signing off or certifying a building’s fire stopping
- Deciding what a wall or floor needs, which belongs to the designer
- Openings that need collars, wraps, batts or boards rather than sealant
If in doubt, ring 01277 525 020 or send details through our quote form and we will say what we think before you book.
What we seal
- Cable penetrations
- Small duct penetrations where the tested detail allows
- Joints between fire-resisting walls and floors
- Linear gaps at wall heads
- Pipe penetrations
- Service gaps in risers
Your questions answered
Do you work on fire-rated sealing in hotels in Hunters Quay?
Yes, to the specification and the product’s tested detail. It goes in to the manufacturer’s tested detail for the wall or floor and the services passing through, and we will tell you if the detail calls for a collar, wrap or batt instead.
What do Scotland’s building standards say about service penetrations in Hunters Quay?
The non-domestic Technical Handbook, clause 2.1.14, expects a penetration to keep at least the wall or floor’s fire resistance period, with proprietary products tested for the use they’re put to. The detail is set by the designer and goes through the warrant process; we install the specified product to its tested detail.
Do you need to see the site first?
Many jobs can be quoted from photos, drawings or a joint schedule. Where they aren’t, we arrange a site visit.
When is resealing likely to be due?
It depends on movement, UV and weather, cleaning, traffic and the product. Treat them as maintenance items and inspect them regularly.
What about RAMS and site documents?
Each site asks for different documents, so tell us what you need and we’ll confirm it when we quote.
How do you choose the sealant?
Where there’s a specification, we use the product it names. If not, we choose for the movement, the surfaces and the conditions, in line with the manufacturer’s guidance.
Does the weather affect the work?
It can, for external work. Sealant won’t bond properly to a wet or frosty joint, so external work may be moved if conditions aren’t right. Internal work is far less affected.