Fire-rated sealing and fire stopping in Parkhouse, Glasgow
We carry out fire-rated and intumescent sealing of service penetrations and linear gaps in Parkhouse and the surrounding area. Send photos or drawings for a fixed quote.
- Unsealed joints where partitions meet the slab
- Fire-stopping items raised at inspection or handover
- Non-fire-rated filler around services
Fire stopping for businesses in Parkhouse
Tell us what needs sealing and where, with photos or drawings if you have them, and we’ll price it.
When something else is needed
Not every problem is a sealant problem, and we are upfront when that’s the case. These need a different solution:
- Signing off or certifying a building’s fire stopping
- Construction that lacks the fire resistance the seal relies on
- Designing or specifying fire stopping, which sits with the designer or fire engineer
If in doubt, call 01277 525 020 or use the quote form and we’ll say what we think.
Where we work in Parkhouse
- Cable penetrations
- Small duct penetrations where the tested detail allows
- Service gaps in risers
- Linear gaps at wall heads
- Joints between fire-resisting walls and floors
- Pipe penetrations
About our fire stopping in Parkhouse
Every service that crosses a compartment wall or floor leaves an opening, and that opening needs sealing to hold back fire and smoke. Our job is fitting fire-rated and intumescent sealant at those service penetrations, and along linear gaps, where it is the specified product. We work to the product’s tested detail for every seal. We work on pipe penetrations, service gaps in risers and small duct penetrations where the tested detail allows, and what we are called in for most is builders’ foam or ordinary silicone in compartment walls and unsealed penetrations discovered above suspended ceilings. Whether you call it commercial sealant work, mastic application or joint sealing, in Parkhouse it comes down to the same thing: the right product in a properly prepared joint.
In smaller Scottish places like Parkhouse, buildings with fire-resisting walls typically include schools, care homes, hotels and health centres. Where services pass through, specified fire-rated sealant is installed following the manufacturer’s guidance for that wall or floor.
Building owners and contractors get the same cover: twelve months on the work we carried out. It doesn’t extend to damage, faults in the building or work by others, and we’re upfront about that.
- Where
- Parkhouse (G22, G20, G21)
- Wider area
- Glasgow
- Cover
- 12 months on every job
- Quote
- A fixed quote before we start
- Call
- 01277 525 020
- Last updated
- 3 November 2026
Commercial clients in Parkhouse
Planned maintenance programmes are welcome: resealing failed joints building by building, on a schedule that suits your budget. Sites in Parkhouse can sit alongside others in a wider programme across Glasgow.
Facilities managers want contractors who arrive with the paperwork sorted. Let us know the documents you need (RAMS, insurance certificate, CSCS details) and we’ll confirm them with the quote.
Also near Parkhouse
Other services in Parkhouse
Should maintenance staff do it?
For a quick touch-up, site staff may be fine, but anything bigger is another matter: a specialist works through quantities efficiently, leaves a consistent finish and backs it with a 12-month guarantee.
Some joints are best left to specialists: for example fire-rated seals that must match a tested detail, trafficked floor joints and external movement joints. A poor seal in places like these tends to cost more to put right later.
Questions we’re asked in Parkhouse
Can you work on a hospital site such as Stobhill Hospital?
Yes. We work in healthcare settings as well as offices and schools. The estates team’s permit system and infection-control rules come first, and the work is planned around them.
How do the Scottish rules apply to fire-rated sealing in Parkhouse?
The non-domestic Technical Handbook, clause 2.1.14, expects a penetration to keep at least the wall or floor’s fire resistance period, with proprietary products tested for the use they’re put to. Design sits with the designer and the verifier; installation to the tested detail is our part.
Do you work to architects’ specifications?
Yes. Include it with the drawings when you ask for a quote, and we’ll price the work to it, flagging anything that needs clarifying.
How long do sealant joints last?
There’s no fixed lifespan: movement, exposure, cleaning, traffic and the product all play a part. Sealant joints are maintenance items, so inspect them regularly.
Do you work in Parkhouse?
Yes. Sites across Parkhouse are covered, and the same phone number covers every area.
Does the weather affect the work?
For external joints, yes. Sealant needs a dry joint and a temperature within the product’s range, so damp, frosty or very cold days can stop external work. Inside work is seldom held up.
What if there’s asbestos in the old mastic?
Some older mastics, especially in pre-2000 buildings, can contain asbestos. We check the asbestos register before cutting out old sealant in an older building, and work stops until any suspect material has been tested. We don’t remove asbestos-containing materials.
Fire stopping around Parkhouse: what changes locally
There are a good number of hotels within about 2 miles of Parkhouse. Hotels are divided into compartments, and refurbishments that add pipes and cables through bedroom and corridor walls leave gaps to close. In Scotland, clause 2.1.14 of the non-domestic Technical Handbook expects service penetrations to keep at least the fire resistance duration of the wall or floor, with proprietary products, intumescent ones included, tested for their end use. Our part is installing the specified fire-rated sealant to its tested detail.
Colleges such as Glasgow Kelvin College - Springburn Campus, 1.1 miles south-east of Parkhouse, add IT and services as courses change, and each new penetration through a fire-resisting wall needs sealing with the specified product. At a university such as Glasgow Caledonian University, which lies south of Parkhouse, labs, lecture blocks and residences are re-serviced often, so penetration seals are best checked after M&E work.
Parkhouse is about 1 mile north-east of North Kelvinside, in Glasgow. Across the G22 postcode area, it works the same way: send details, get a fixed quote, we seal, and the work is guaranteed. We work across 171 places in Glasgow, from busy centres to rural villages.
Business premises anywhere in G22, G20 and G21 are within our area for service penetrations. Streets here include Birsay Road, Walnut Road and Balmore Road, and sites on any of them can send details for a fixed quote. Parkhouse sits on or close to the A879, useful when we plan access and materials. If your building is just outside Parkhouse, we cover Possilpark (1 mile south), Milton (1 mile north), Lambhill (1 mile west), Cowlairs (1 mile south-east) and Ruchill (1 mile west). Nearby towns on our patch include Glasgow (3 miles south), Calton (3 miles south), Langside (5 miles south), Yoker (5 miles west), Partick (3 miles south-west) and Mount Florida (5 miles south).
Landmarks near Parkhouse
We work on buildings around Glasgow University Library and Springburn Park and the streets around them. There’s a railway station in Parkhouse itself: Ashfield station. Other landmarks nearby include Ruchill Hospital (0.6 miles south-west) and Heatherbank Museum of Social Work (1.6 miles south). Not far away are Hogganfield Loch and Castle Hill.
Diagnose, treat, sign off
Before any cutting starts, the area is protected: tape along each joint edge and covers over finishes, stock and equipment close by. The work itself normally takes longer where risers, ceiling voids or occupied floors have to be worked through in sequence, and our waste is bagged and taken away as we go. For work around Parkhouse, we aim for one trip, so photographs, sizes and a full list matter. External joints need a dry spell as well.
- First we confirm the product and tested details named in the specification.
- Openings are measured and grouped by detail.
- Old or wrong materials are cut out.
- Where the detail needs backing, it goes in at the stated depth.
- Fire-rated or intumescent sealant goes in around the services and is tooled off.
- We walk the completed areas with you and confirm the records agreed at quote stage.
Before we start on site
- Tell us which areas need to stay in use
- Clear stock, furniture or equipment away from the joints
- Confirm the product named in the specification
Request a quote
Every quote starts with the facts: what’s there, how much of it, how we reach it and what’s specified. Send what you have, and we’ll arrange a site visit if anything is unclear.
Read more
Common problems we fix in Parkhouse
Fire stopping can get squeezed at the end of a programme, or done by whoever is on site. That is how unsuitable products and improvised details end up in compartment walls and later need putting right.
What tends to prompt an enquiry:
- Fire sealant pulled out of the opening
- Snag lists that include open service penetrations
- Fire seals cut back for extra cables and never reinstated
- Head-of-wall gaps with no fire seal
Theatres, wards and plant rooms at sites like Stobhill Hospital, 1.2 miles to the east of Parkhouse, all have compartment walls crossed by services.
What to look for in a quote
- What the guarantee covers, and for how long
- What level of public liability insurance do they hold?
- Their plan for phasing and protecting the area
- Which product they’ll use, and why it suits the joint
Surface by surface
Drylining partitions
Holes in board are often cut larger than needed. If the gap exceeds the tested range, sealant alone won’t do.
Risers and ceiling voids
Openings above suspended ceilings are easy to miss. We follow your schedule area by area and tell you about openings outside the list.