Expansion Joint Sealing in Burravoe
Looking for expansion joint sealing in Burravoe? It’s simple: send details, get a quote, we seal, guaranteed.
- Expansion joints filled with dirt and stones
- Chipped joint edges on forklift routes
- Water getting into the wall through a failed joint
Expansion joint sealing in Burravoe
Tell us what needs sealing and where, with photos or drawings if you have them, and we’ll price it.
Questions we’re asked in Burravoe
Do we have to stop operations in Burravoe while the joints are sealed?
Typically not: we work in sections and hand each one back once it has cured. Tell us which hours and entrances we can use and we will plan from there.
Can being near the sea in Burravoe affect the sealant we need?
It can. Wind-driven rain and, closer to the shore, salt air are harder on external joints. Product choice and preparation matter more, and sea-facing elevations are worth inspecting more often.
Do you hold CHAS accreditation?
Yes. Mastic Doctor is CHAS accredited and a Constructionline member.
Can you seal car park deck joints?
Yes. Let us know the opening hours and which levels or bays have to stay available and we will plan around them.
How do I request a quote?
You can use the quote form on this site; alternatively, ring 01277 525 020 or email the details over. Photos, drawings or a joint schedule help us quote quickly.
Are you insured?
Yes. Mastic Doctor is fully insured, public liability included.
Can you work while the building is occupied?
Normally, yes. Phased work can be planned so areas stay in use.
Expansion joint sealing in Burravoe, done properly
If you need expansion joint sealing in Burravoe, start with photographs and joint lengths. Send them through our quote form, and we’ll arrange a site visit if needed, then send a fixed quote that names the sealant. To discuss the joints first, give us a call on 01277 525 020 or email drawings and photos. Site teams most often ask us about water getting into the wall through a failed joint and sealant peeling off one face of the joint, on brickwork movement joints, cladding panel joints and precast concrete panel joints. Searching for sealant specialists in Burravoe? We have been sealing commercial buildings since 2005, with CSCS-carded applicators.
In smaller places such as Burravoe, the joints we’re asked about sit in workshops, farm sheds, schools and halls. Slabs and yards take vehicles, rain and frost.
Work we carry out comes with a 12-month guarantee. If an installation problem shows up, phone 01277 525 020 or use the quote form and we will arrange a return visit.
- Place
- Burravoe (ZE2)
- Region
- Shetland Islands
- Cover
- 12 months on every job
- Quote
- A fixed quote before we start
- Call
- 01277 525 020
- Page updated
- 3 November 2026
Also in Burravoe
Why act early in Burravoe
On a car park, resealing joints in phases keeps the deck open. Work can be planned so parts of the deck stay open. Tell us what has to stay open and we will plan around it. In Scotland, wind-driven rain finds a failed joint quickly, so it’s worth renewing joints around Burravoe before they leak.
A quote for movement joints depends on quantities, condition and access, and any specification that applies. Ask us for a fixed quote.
What you get with us
- Work to your specification and the manufacturer’s guidance
- Colours confirmed for the specified product
- CHAS accredited
- A Constructionline member, so easy to vet
Read what affects the cost and our accreditations and insurance.
Keeping the joints sound
To get the most from the new sealant:
- Look over external and deck joints after a hard winter
- Plan racking layouts so feet don’t land on a joint
- Put movement joints on the planned maintenance inspection round
- Brief car park operatives to protect joint lines during winter clearance
Movement joints belong on the planned maintenance inspection list. A periodic look picks up tears and lifting before water gets in. If anything looks wrong, speak to us on 01277 525 020 or email us with photos.
On a multi-storey car park, a failed joint usually shows up as a leak onto the deck underneath. That water often carries de-icing salts with it, which is bad news for the concrete and the people parking below. Sealing the joint promptly stops it at source.
Our process
Before any cutting starts, the area is protected: masking tape along the joint edges and sheeting over anything nearby. The work itself typically takes anything from part of a day to a couple of weeks, depending on joint lengths, widths and access, and our waste is bagged and taken away as we go. Jobs near Burravoe are often grouped with others in the same area, to make the most of each trip. Tell us how flexible your dates are.
- We start with photographs, approximate lengths and any drawings, visiting where needed.
- Joint widths and expected movement are checked against what the sealant can take, and flag anything that needs an engineer.
- Every joint is cleared of the failed seal and any grit packed into it.
- Edges are checked, and we tell you if any need repairing before sealing.
- The right sealant goes in at the right depth, bonded to the two sides only.
- Areas reopen once cured, and the work carries our 12-month guarantee.
Preparing the site
- Flag any permit to work we will need
- Warn occupants and staff about the work
- Point out any areas we must not close
Ask for a quote
A good quote starts with a clear picture: what’s there, how much of it, how we reach it and what’s specified. Share whatever details you have and we’ll fill any gaps with a visit.
Related advice
What affects the price in Burravoe
A fixed quote reflects the actual work. It takes account of:
- Which sealant the job calls for
- How accessible the joints are
- Quantities, in metres or numbers
- The size and state of each joint
The product called for affects the cost, as does the preparation each joint needs, such as cutting out, priming or new backing rod. Access, phasing and site rules also count.
What to include in your enquiry
A few photographs plus some basic facts will normally do. Please tell us:
- The type of building and who uses it
- Drawings or a marked-up plan, if available
- A wide shot and a close-up of the area
- Where the site is, with the postcode
If there’s a specification, drawings or a tender package, send it with your enquiry, and we will price the work to it. Smaller jobs need nothing more than photographs and a few notes.
General trades versus a specialist
Site maintenance staff can often handle a short internal joint. Where it goes wrong is preparation: sealing over old material, sealing onto damp or dusty surfaces, or a product that can’t take the movement.
Using site staff can make sense for a small touch-up, but larger jobs are different: a specialist brings efficiency, a consistent finish and a 12-month guarantee.
Where floor joints take the most wear near Burravoe
Burravoe sits close to the coast, within about 1 mile. Near the sea, external slabs, ramps and decks see salt air and driven rain as well as their usual loads, so a failed joint lets more in and the edges break up sooner. Island jobs, Burravoe among them, are planned around the ferry and the forecast. Approximate joint lengths and widths let us bring enough material first time.
Around Burravoe, open joints collect water and debris, and the arrises are the next to go. In and around Burravoe, the right filler or sealant for each joint depends on the traffic and the movement it takes.
Burravoe is in the Shetland Islands. Commercial clients in Burravoe can call on us for movement joints. 63 places across the Shetland Islands fall within our area, including Burravoe.
If you need expansion joint sealing in ZE2, the process matches everywhere else we work: details, then a fixed price, then sealing and a 12-month guarantee. Buildings on Brough Road and Meadow Bank Road are within our area for movement joints. Just outside Burravoe, we also work in Aywick (4 miles north), Mossbank (5 miles south-west), Firth (6 miles south-west), Mid Yell (7 miles north) and Vidlin (9 miles south). Island and remote sites need extra planning, with travel, ferry crossings where needed and weather to allow for, so give the site location in your enquiry.
What’s near Burravoe
Nearby you’ll also find The Old Haa (less than half a mile south). For a walk, there’s Loch of Vatswick.
Different surfaces, different methods
Internal floor movement joints
Warehouse and retail floors have saw-cut induced joints and construction joints. A semi-rigid filler is common in trafficked industrial floors, with a flexible sealant where movement is larger.
Joints between different materials
Some mixed-material joints suit a hybrid sealant. The choice depends on the substrates and how much the joint moves.