Fire-rated sealing and fire stopping in Vidlin, Shetland Islands
Fire-rated and intumescent sealing of service penetrations and linear gaps in Vidlin and across the Shetland Islands. CHAS accredited, Constructionline member, with a 12-month guarantee on workmanship.
- Damaged fire seals in risers and voids
- Snag lists that include open service penetrations
- Openings left by services added after handover
Fire stopping across Vidlin
Share the site address and what’s failing, and we’ll reply with a fixed quote or arrange a visit.
Fire stopping in Vidlin
We should be clear about what we do and don’t do. The designer, fire engineer or building control decides which fire stopping is required. What we bring is careful installation of the specified sealant, to the maker’s guidance on sites in Vidlin. If you are dealing with unsealed joints where partitions meet the slab and fire stopping installed outside its tested range, we can put it right, whatever the surface. Facilities teams, main contractors and managing agents in Vidlin tend to want the same three things: a clear scope, tidy work and joints that don’t fail again.
Hotels and care homes around smaller places like Vidlin often have services added during refurbishment. We fit the specified fire-rated sealant as its published detail shows and raise it if another product is needed.
Our workmanship is guaranteed for 12 months, in Vidlin as everywhere else we work. If a joint we sealed fails because of how it was installed, we come back and put it right.
- Location
- Vidlin (ZE2)
- Wider area
- Shetland Islands
- Cover
- 12 months on every job
- Quotes
- Fixed quote, scope in writing
- Call
- 01277 525 020
- Last updated
- 3 November 2026
Common questions from Vidlin clients
Do you work on the island where Vidlin is?
Yes. Every Scottish council area is within our area, and that includes island locations such as Vidlin. Ferry times and the weather set the plan, so we ask for photos and a full list first.
Do you decide the fire-stopping details for buildings in Vidlin?
No. The designer or fire engineer sets the detail and building control accepts it. Our part is installing the specified product to its tested detail, and telling you if the detail calls for something other than sealant.
What’s the quickest route to a quote?
There are four steps: send details, receive a fixed quote, we carry out the work, and it’s guaranteed. Step one needs little more than photos and a postcode.
When can you be on site?
The office is staffed Monday to Friday, from 8am until 5pm. Tell us your site hours and access windows and the work will be fitted around them.
What will the job cost?
We don’t publish prices, as every site differs. With photos or drawings, we can give you a fixed quote.
Are you fully insured?
Yes. Our insurance certificate can be sent alongside the quote.
How long does a job like this take?
The duration is planned around your programme and the access we are given. We will give you an estimate of time on site when we quote.
Our process
We begin with a short walk round with whoever looks after the building, agreeing which joints are in scope, where to start and what must stay open. After that, any old or failed material is removed, each joint is prepared and the new sealant goes in. For a building near Vidlin, directions, keys and a contact on the day are worth sorting early. We will confirm the plan with the fixed quote.
- We start with your penetration schedule, drawings or specification.
- We plan the sequence of floors, risers and voids with you.
- Each opening is checked for wall or floor type, service, gap and depth.
- Foam, ordinary sealant and debris come out so the seal starts clean.
- The specified backing and sealant go in to depth and are finished neatly.
- Anything outside the detail is reported to you rather than sealed.
Before we start on site
- Confirm the product named in the specification
- Tell staff and tenants when we’ll be in
- Point out any areas we must not close
Quotes
Quotes are fixed against the scope you send, so the cost is agreed before work starts. To start the process, phone 01277 525 020 or email us.
Advice
Other services in Vidlin
Why it’s worth doing now in Vidlin
Inspections and handover checks often pick up fire stopping. Late discoveries can delay handover while openings are reopened and resealed. Exposed buildings in Scotland take a lot of weather, and for a smaller place like Vidlin, a repair visit takes planning, so it’s better to act early.
We don’t publish prices, because the scope varies so much from one building to the next. For a fixed figure, call for a quote.
Why clients in Vidlin choose us
- CSCS-carded applicators
- Joints cleaned back to sound surfaces
- Sealing commercial buildings since 2005
- A fixed quote before work starts
Read our cost guide and our accreditations.
Where services cross fire walls in Vidlin
For an island location such as Vidlin, work is planned around ferry crossings and the weather. The specification and photos of each penetration let us bring the right products first time. Scottish guidance (non-domestic Technical Handbook, clause 2.1.14) asks that penetrations match at least the fire resistance period of the element they pass through, and products should be tested for their end use. We install fire-rated sealant to that tested detail where it is specified.
Around Vidlin, we install fire-rated and intumescent sealant to the product’s tested detail wherever it is the specified product.
Vidlin is in the Shetland Islands. We send applicators to Vidlin for service penetrations. We work across 63 places in the Shetland Islands, from busy centres to rural villages.
Work on service penetrations is covered throughout ZE2, whatever the building. Nearby places we also cover include Dury (4 miles south), Hamister (4 miles east), Voe (4 miles west), Symbister (4 miles south-east) and Sandwick (4 miles south-east) for service penetrations. Remote and island addresses take more planning, from travel and ferries to the weather, so mention the location when you phone 01277 525 020 or send details through our quote form.
Near you in Vidlin
Nearby you will also find The Cabin Museum (1.5 miles south-west). The countryside around Vidlin includes Kirkhouse Loch and Setter Hill.
Do you need fire stopping in Vidlin?
Some seals fail because the wrong product went in: builders’ foam or ordinary silicone used to fill a hole. It may look closed, but it has no tested fire performance in that position.
Most enquiries start with one or more of the following:
- Fire seals cut back for extra cables and never reinstated
- Openings found when ceilings come down for a refit
- Fire-stopping items raised at inspection or handover
- Expanding foam used as fire stopping
For any site around Vidlin, we work to the specification and the manufacturer’s installation guidance, leaving design and sign-off with the designer.
Questions to ask before you book
- Which product they’ll use, and why it suits the joint
- Whether their applicators hold CSCS cards
- Will failed sealant be removed rather than covered?
- The terms of the workmanship guarantee
What affects the price in Vidlin
Your fixed quote is built from the real scope. It allows for:
- Distance, for remote addresses
- Phasing around occupants
- Removal of failed or old sealant
- Specialist products, such as fire-rated or hygienic sealants
A quote for service penetrations depends on quantities, condition and access. Call for a quote.
What to include in your enquiry
Good information means a firmer quote. When you get in touch, include:
- Asbestos survey details if the building is older
- The product your specification calls for
- Clear photos of the problem areas
- The type of building and who uses it
Pricing a project or setting a maintenance budget? Send the scope and any drawings, and we will return a fixed quote you can plan around. If you have questions first, call 01277 525 020 or email us.
Commercial clients in Vidlin
If you look after buildings for someone else, clear figures and clear communication matter. We quote a fixed sum, confirm the scope and walk the finished work with you or your representative.
Hospitality, education, healthcare, office and retail clients come to us directly as well. We plan around the way the building is used, so the building keeps working while we do.
General trades versus a specialist
General builders and handymen seal joints, but it isn’t their main trade. A specialist prepares properly, controls joint depth and picks a product with the right movement class.
Using site staff can make sense for a small touch-up, but larger jobs are different: a specialist works through quantities efficiently, leaves a consistent finish and backs it with a 12-month guarantee.