Fire Stopping in Chale
We carry out fire-rated and intumescent sealing of service penetrations and linear gaps in Chale. Send details for a fixed quote.
- Fire sealant pulled out of the opening
- Fire-stopping items raised at inspection or handover
- Damaged fire seals in risers and voids
Fire stopping for businesses in Chale
Send drawings, photos or a joint schedule, or tell us about the site, and we’ll come back with a fixed quote.
For managing agents and facilities managers
Planned maintenance programmes are welcome: working through a building or an estate in stages that fit your budget. Sites in Chale can sit alongside others in a wider programme across the Isle of Wight.
Facilities managers want contractors who arrive with the paperwork sorted. Tell us what site paperwork you need, such as RAMS, an insurance certificate or CSCS details, and we’ll confirm with the quote.
Fire stopping in Chale, done properly
A lot of fire-stopping work comes after M&E installation, a refit or a tenant fit-out. New cable runs, replaced pipework and extra data routes all punch holes in compartment walls, and they are easy to forget. We close the openings listed on your schedule, using the specified sealant and detail. Most enquiries involve seals disturbed by maintenance and left open and unsealed penetrations discovered above suspended ceilings, across service gaps in risers, joints between fire-resisting walls and floors and linear gaps at wall heads. Sealant applicators who only do sealant are a different proposition from a general trade with a gun in the van: on jobs in Chale, preparation and product choice get the time they need.
For a smaller site near Chale, we plan to do all the penetrations in one go, with the specification and photos sent in advance. We install to the specification and the manufacturer’s guidance, leaving design and sign-off with the designer and building control.
Every job is signed off with a 12-month guarantee. It’s a plain promise: if our work fails within that year, we put it right.
- Location
- Chale (PO38)
- Region
- Isle of Wight
- Cover
- 12 months on our workmanship
- Quote
- Fixed quote, scope in writing
- Phone
- 01277 525 020
- Page updated
- 3 November 2026
Towns and villages near Chale
More services for Chale
Questions about Chale
How does the removal of BS 476 from Approved Document B affect fire-rated sealing in Chale?
From 2 September 2029, Approved Document B drops its BS 476 references in favour of BS EN 13501-2 classification, with transitional arrangements. Whichever applies, we install the specified product to its tested detail; the specification is for the designer to set.
Is Chale too far out for you?
Not at all: smaller places are covered as well as towns. We work across Greater London and the South East. Where we can, we group nearby jobs to make the most of each trip.
Are your applicators CSCS-carded?
Yes. Our applicators hold CSCS cards, as many construction sites ask for.
What happens if old sealant might contain asbestos?
Asbestos is possible in some older mastics, particularly in buildings from before 2000. We check the asbestos register before cutting out old sealant in an older building, and work stops until any suspect material has been tested. Removing asbestos is a job for asbestos specialists, not us.
Can staff carry on working while you are here?
In most cases, yes. We phase the work so most of the building stays in use, with each area protected and signed.
What will the job cost?
Each job is quoted on its own details. For yours, call 01277 525 020 or email drawings and photos with a description of the work.
What’s the quickest route to a quote?
The quote form is the simplest route, though you can also ring 01277 525 020 or email the details over. Photos, drawings or a joint schedule help us quote quickly.
From enquiry to sign-off
Before any cutting starts, the area is protected: masking tape along the joint edges and sheeting over anything nearby. The work itself usually takes longer where risers, ceiling voids or occupied floors have to be worked through in sequence, and we clear our waste as we work. For work around Chale, we aim to finish in one visit, so we ask for photographs and rough sizes first. Then the right materials arrive with us.
- The specification and schedule come first, so we know which details apply.
- We plan the sequence of floors, risers and voids with you.
- We compare every service penetration with its tested detail before sealing.
- Foam, ordinary sealant and debris come out first.
- The specified backing and sealant go in to depth and are finished neatly.
- We tell you about openings that need a different product.
Getting the site ready
- Tell us your opening times and when work is allowed
- Clear stock, furniture or equipment away from the joints
- Flag any permit to work we will need
Ask for a quote
Tell us about the building, the joints and when you need the work done, and we’ll put a fixed quote together. The easiest way is to call 01277 525 020 or send details through our quote form.
Advice
After the work
Keep the joints in good shape with a few simple steps:
- Ask which product is in place before decorating
- Ask the designer to confirm details early on refits
- Include service cupboards in routine inspections
- Record which product was used where
Don’t patch a fire-rated seal with anything outside its tested detail. Repairs need the same product and detail as the original unless the designer specifies otherwise.
The simplest way to keep compartment walls intact is to plan fire stopping into every job that crosses them. Then the seal goes in while the area is open instead of being left for someone else.
How the job changes by surface
Plastic pipes
In a fire, plastic pipework melts away and leaves an opening. Small sizes are sometimes covered by an intumescent sealant detail, but many need a collar or wrap. We confirm material and size first and tell you if sealant isn’t the right product.
Risers and ceiling voids
Openings above suspended ceilings are easy to miss. We follow your schedule area by area.
Compartment walls and floors in Chale
For England, the fire stopping of penetrations is dealt with in Approved Document B. The national BS 476 classes are due to drop out of it from 2 September 2029, leaving the European BS EN 13501-2 route, subject to transitional arrangements. What we install is set by the specification, and it goes in to the tested detail.
Theatres, wards and plant rooms at sites like Whitecroft Hospital (5.2 miles north of Chale) all have compartment walls crossed by services.
Chale is about 7 miles south of Newport, in the Isle of Wight. Across the PO38 postcode area, the process is the same: send details, get a fixed quote, we seal, and the work is guaranteed. Across the Isle of Wight, 125 places are covered, including Chale. We also cover Portsmouth, some 18 miles away.
Commercial sites across PO38 are covered for service penetrations. Buildings on Church Place, Upper House Lane and Blythe Shute are within our area. Close to Chale, our area also takes in Blackgang (1 mile south-east), Pyle (1 mile north-west), Chale Green (1 mile north), Atherfield Green (1 mile north-west) and Niton (2 miles south-east). A short drive away, we cover Newport (7 miles north), Ryde (11 miles north-east), Cowes (11 miles north), Sandown (8 miles north-east), Shanklin (7 miles east) and Ventnor (5 miles east). Remote and island addresses take more planning, from travel and ferries to the weather, so give the site location in your enquiry.
What’s near Chale
Nearby you’ll also find Whitecroft Hospital (5.2 miles north) and Blackgang Sawmill Museum (0.6 miles south). Not far away are Stenbury Down.
General trades versus a specialist
There’s also the paperwork. Many sites expect CSCS cards, RAMS and proof of insurance, and we will confirm the paperwork you need with the quote.
Using site staff can make sense for a small touch-up, but anything bigger is another matter: a specialist works through quantities efficiently, leaves a consistent finish and backs it with a 12-month guarantee.
Common problems we fix in Chale
Linear gaps fail where a fire-resisting wall meets a slab, soffit or another wall. Deflection and building movement can open these gaps. The tested detail for a linear joint states the width and movement it covers.
Things that normally lead to an enquiry:
- Fire sealant pulled out of the opening
- Penetration schedules that need working through
- Expanding foam used as fire stopping
- Open linear gaps along the top of fire-resisting walls
Halls and meeting rooms at places like St Andrew's Church sometimes gain new services, and any compartment wall crossed needs the specified seal.
Comparing quotes
- Will failed sealant be removed rather than covered?
- What the guarantee covers, and for how long
- Proof of insurance
- Who will actually carry out the work