Ryde fire stopping
Fire stopping in Ryde, backed by over 20 years in commercial sealing. Fully insured and CHAS accredited.
- Fire stopping installed outside its tested range
- Old intumescent sealant that has split away
- Open linear gaps along the top of fire-resisting walls
Fire stopping for Ryde sites
Send drawings, photos or a joint schedule, or tell us about the site, and we’ll come back with a fixed quote.
Fire stopping in Ryde
Opened ceilings and riser doors often reveal service openings nobody sealed. Where the walls and floors already have a fire-stopping specification, we can work to it, matching the product and detail it names. Where there isn’t one, the designer or fire engineer needs to set one first. The enquiries we see most involve openings left by services added after handover and old intumescent sealant that has split away, on joints between fire-resisting walls and floors, cable penetrations and service gaps in risers. Facilities teams, main contractors and managing agents in Ryde tend to want the same three things: a fixed quote, no surprises on site and a 12-month guarantee behind the result.
Towns the size of Ryde have plenty of buildings with compartment walls: schools, care homes, surgeries, offices and blocks of flats. Whenever new services go through those walls, the gaps need sealing with the specified product.
A 12-month guarantee applies to all our work in the Isle of Wight. If an installation problem shows up, phone 01277 525 020 or email a schedule or drawings and we will arrange a return visit.
- Location
- Ryde (PO33)
- Wider area
- Isle of Wight
- Cover
- 12 months on every job
- Quote
- Quoted before any work starts
- Call
- 01277 525 020
- Last updated
- 3 November 2026
Questions we’re asked in Ryde
How does the move away from BS 476 affect penetration seals in Ryde?
Approved Document B loses its BS 476 references from 2 September 2029, and BS EN 13501-2 becomes the route, subject to transitional arrangements. Whichever applies, we install the specified product to its tested detail; the specification is for the designer to set.
Would you work within a site like Gosport War Memorial Hospital?
Yes, provided the work is planned with the site’s estates team. The estates team’s permit system and infection-control rules come first, and the work is planned around them.
Is colour matching possible?
That depends on the product. Some ranges offer many colours, others very few, so we’ll confirm the colours available for the specified product with the quote.
What will the job cost?
We don’t publish prices, because every site is different. With photos or drawings, we can give you a fixed quote.
Is it fine to apply new sealant on top of old?
No. We cut the old material out and clean the joint back before sealing, since fresh sealant will not bond reliably to aged material.
Do you work to architects’ specifications?
Yes. The specification and the manufacturer’s installation guidance are what we work to, and any queries are raised before we start.
Does the weather affect the work?
Outside, yes. Sealant needs a dry joint and a temperature within the product’s range, so frost, rain or cold mornings can delay outside work. Inside work is seldom held up.
How a job runs
Site rules come first: signing in, inductions and any permit to work. With the paperwork done, we take the joints in the sequence agreed with you. Parking and loading for town-centre jobs in Ryde are worth mentioning when you send details. On estates and business parks it’s usually simpler.
- We ask for the product and detail your designer has specified.
- Openings are measured and grouped by detail.
- Improvised fillers and failed sealant are removed.
- Mineral wool or other backing is fitted where required.
- We gun the sealant in to the specified depth around each service and tool it.
- We walk the completed areas with you and confirm the records agreed at quote stage.
Preparing the site
- Tell us which areas need to stay in use
- Warn occupants and staff about the work
- Share your working hours and any access restrictions
Getting a fixed quote
A handful of photos and a postcode is the fastest way to a quote. Send them through the quote form, or call 01277 525 020 or email a schedule or drawings to discuss it first.
Read more
Quoting for work in Ryde
These are the things that shape the price:
- Whether old sealant has to be cut out first
- Distance, for remote addresses
- Access and working height
- Induction, permit and paperwork requirements
Small jobs and large programmes are priced from the same things: what’s in scope, how we reach it, what’s specified and when it needs doing. Call for a quote and we will put a fixed figure on it.
Sending details for a quote
It doesn’t need to be a full survey. A few details are enough to get going:
- When you need the work done
- Anything awkward about access or site hours
- Clear photos of the problem areas
- Where the site is, with the postcode
To get a fixed quote, call 01277 525 020 or email a schedule or drawings with the site address and an outline of the work. Our quote form is another easy route.
Fire stopping around Ryde: what changes locally
Approved Document B is the English guidance that covers fire stopping around openings and penetrations. Its BS 476 references are being withdrawn from 2 September 2029, with BS EN 13501-2 classification taking over, subject to transitional arrangements. Our part stays the same: the specified product, installed to its tested detail. There are plenty of hotels within about 2 miles of Ryde. Bedroom-to-corridor walls in hotels are normally fire-resisting, so new cabling or pipework through them has to be sealed to the tested detail.
Hotels such as The Castle Hotel (less than half a mile north of Ryde) rely on fire-resisting walls between bedrooms and corridors, and refits that add services leave penetrations to seal where fire-rated sealant is specified. Halls and meeting rooms at places like All Saints' Church sometimes gain new services, and any compartment wall crossed needs the specified seal. Schools such as Dover Park Primary School often have new data and services installed during holidays, and penetrations through fire-resisting walls should be checked afterwards.
Ryde is about 6 miles south of Gosport, in the Isle of Wight. We cover Ryde and the rest of the Isle of Wight, with the same fixed quotes and 12-month guarantee as everywhere else. We work across 125 places in the Isle of Wight, from busy centres to rural villages. Our Portsmouth page has more on work in that area, about 7 miles away.
We take on service penetrations across the PO33 postcode area, whatever the building. We cover commercial and managed buildings on High Street, St Thomas' Square and Market Street and the roads nearby. Being close to the A3054 and A3055, Ryde is straightforward for us to reach. We also cover Oakfield (1 mile south-east), Haylands (1 mile south-west), Elmfield (1 mile south-east), Appley (1 mile east) and Westridge (1 mile south-east). Bigger towns within reach include Newport (6 miles west), Cowes (7 miles west), Sandown (5 miles south), Shanklin (6 miles south), Ventnor (9 miles south) and East Cowes (6 miles west). Among the larger centres in the Isle of Wight is Ryde, and its commercial and public buildings are all within our area. Remote and island addresses take more planning, from travel and ferries to the weather, so give the site location in your enquiry.
Local landmarks in Ryde
Recent enquiries here include premises near Ryde Academy, The Falcon pub and Ryde School with Upper Chine. There’s a railway station in Ryde itself: Ryde St Johns Road station. Well-known places in the area include Gosport War Memorial Hospital (4.8 miles north) and Sandown Castle (4.7 miles south). The countryside around Ryde includes Brading Down and Alan Hersey Nature Reserve.
Different surfaces, different methods
Small ducts
Some fire-rated sealant details cover small ducts. Bigger ducts and fire-resisting ductwork are normally handled with other products and we flag that rather than guess.
Plastic pipes
Waste and drainage pipes through floors are a frequent case. The detail decides whether sealant alone is enough.
Site staff or a sealant specialist?
The visible bead is only part of the job. Backing rod, primer where specified and a joint designed to move with the building are easy to get wrong without experience.
Site maintenance staff can often handle a short internal joint. The usual problems come from preparation: sealing over old material, sealing onto damp or dusty surfaces, or a product that can’t take the movement.
Why deal with it now?
Leave a penetration open and smoke and fire can cross into the next compartment far earlier than intended. While the openings can be reached, sealing them is normally straightforward. Wait until ceilings close or areas are occupied and the same work becomes harder to reach. Many buildings in towns like Ryde have been extended or altered, and joints where old meets new tend to fail first. Renewing them before water gets in protects the fabric.
Access often affects the price as much as the sealing: easy-to-reach joints are quicker than those that need equipment to get to. Mention the access as part of your enquiry.
Why us?
- Constructionline member for supplier checks
- One number for every site we cover
- Work to your specification and the manufacturer’s guidance
- Over 20 years of commercial sealing
Read our cost guide or our accreditations.
More services for Ryde
For managing agents and facilities managers
For main contractors, we work as the sealant subcontractor. Programme, specification and site rules come first, with CSCS-carded applicators on site.
Building owners and managing agents use us on sealant work across single buildings or whole portfolios around Ryde. One quote can cover more than one site, so there’s one set of paperwork to deal with.