Fire Stopping in Balintore
Fire-rated and intumescent sealing of service penetrations and linear gaps across Balintore, carried out by CSCS-carded applicators. Fully insured and CHAS accredited.
- Seals that don’t match their tested detail
- Snag lists that include open service penetrations
- Head-of-wall gaps with no fire seal
Fire stopping in Balintore
Tell us what needs sealing and where, with photos or drawings if you have them, and we’ll price it.
FAQs: Balintore
Does your area include sites such as Cadboll Industrial Estate, near Balintore?
Yes. We cover Balintore and the area around it, including industrial estates, business parks and retail parks such as Cadboll Industrial Estate. To start, just ring 01277 525 020 or email drawings and photos with the unit, the joints involved and your access times.
Which Scottish guidance covers penetration seals in Balintore?
Under Scotland’s non-domestic Technical Handbook (clause 2.1.14), service penetrations should keep at least the wall or floor’s fire resistance duration, using products tested for their end use. Design sits with the designer and the verifier; installation to the tested detail is our part.
Do your applicators hold CSCS cards?
Yes. If you need card details for site access, let us know and we’ll send them with the quote.
Will you quote for a small job?
Whatever the size, the process is the same: details, then a fixed price, then sealing, then a 12-month guarantee.
Is the work guaranteed?
Yes. The 12-month guarantee covers our preparation and application, though not damage or work by other trades.
How do we ask for a quote?
There are four steps: send details, receive a fixed quote, we carry out the work, and it’s guaranteed. The first step only needs photos and a postcode.
Are you fully insured?
Yes. Mastic Doctor is fully insured, public liability included.
Fire stopping in Balintore
Penetration seals are fire tested to BS EN 1366-3 and linear joint seals to BS EN 1366-4 and the results are classified to BS EN 13501-2. A rating such as EI 60 only holds when the product is installed as it was tested. So our job is to reproduce that arrangement faithfully. The enquiries we see most involve snag lists that include open service penetrations and unsealed openings around new pipes and cables, on joints between fire-resisting walls and floors, small duct penetrations where the tested detail allows and cable penetrations. Whether you call it commercial sealant work, mastic application or joint sealing, in Balintore it comes down to the same thing: failed joints cut out, faces prepared and the right sealant laid to the right depth.
Refurbishments in small hotels, schools and care homes around places like Balintore can leave gaps around new services. We fit the specified fire-rated sealant as its published detail shows and raise it if another product is needed.
Every job we finish is backed by a 12-month workmanship guarantee. If our installation lets you down in that time, we return and fix it.
- Place
- Balintore (IV20)
- Wider area
- Highland
- Cover
- A 12-month guarantee
- Price
- A fixed quote before we start
- Phone
- 01277 525 020
- Page updated
- 3 November 2026
Owners, agents and contractors
For main contractors, we work as the sealant subcontractor on new-build and refurbishment projects. We work to your programme, your specification and your site rules.
Facilities managers want contractors who arrive with the paperwork sorted. Let us know the documents you need (RAMS, insurance certificate, CSCS details) and we’ll confirm them with the quote.
Fire stopping around Balintore: what changes locally
Under the Scottish non-domestic Technical Handbook, clause 2.1.14, penetrations should be fire stopped to at least the wall or floor’s fire resistance duration, with proprietary products, intumescent ones included, tested for their end use. Our part is installing the specified fire-rated sealant to its tested detail.
Around Balintore, we install fire-rated and intumescent sealant to the product’s tested detail wherever it is the specified product. Industrial units on estates such as Cadboll Industrial Estate (1.3 miles north of Balintore) often separate offices from warehouse space with fire-resisting walls, and new services through them need the specified seal.
Balintore is about 12 miles north of Nairn, in Highland. We send applicators to Balintore for service penetrations, handled exactly as we handle every other area. Our Highland coverage takes in 256 places, from busy centres to rural villages. Aberdeen is covered too, around 79 miles from Balintore.
If you need fire stopping in IV20, the process matches everywhere else we work: details, then a fixed price, then sealing and a 12-month guarantee. If your site is on Main Street, Bank Street and Ross Street or close by, send details and we’ll quote for service penetrations. We also cover Shandwick (1 mile south-west), Hilton of Cadboll (1 mile north-east), Loans of Tullich (1 mile north-west), Fearn (2 miles north-west) and Hill of Fearn (2 miles north-west) for service penetrations. Further afield, our area takes in Nairn (12 miles south), Tain (6 miles north-west), Alness (13 miles west), Dornoch (10 miles north-west), Invergordon (10 miles south-west) and Fortrose (14 miles south-west). Island and remote sites need extra planning, with travel, ferry crossings where needed and weather to allow for, so give the site location in your enquiry.
Local landmarks in Balintore
For rail, the closest station is Fearn station, roughly 3.4 miles north-west. Not far away are Loch Eye.
Should maintenance staff do it?
A short, simple internal joint is often within reach of a maintenance team. Where it goes wrong is preparation: sealing over old material, sealing onto damp or dusty surfaces, or a product that can’t take the movement.
General builders and handymen seal joints, but it isn’t their main trade. A specialist brings correct preparation, depth control with backing rod and a product suited to that particular joint.
Towns and villages near Balintore
What else we do in Balintore
How a job runs
We follow your site rules from the start: signing in, inductions and any permit to work. With the paperwork done, the joints are worked through in the order agreed with your site contact, and each area is checked before we leave it. For a building near Balintore, directions, keys and a contact on the day are worth sorting early. We’ll confirm the plan with the fixed quote.
- First we go through the drawings, schedule or specification for the seals.
- Every penetration is compared with its detail: wall or floor type, service, gap size and depth.
- Anything that doesn’t belong in the opening, such as expanding foam or general-purpose filler, is removed.
- Mineral wool or other backing goes in wherever the detail asks.
- We apply the specified sealant to the depth and around the services as the detail shows.
- If an opening needs something other than sealant, we tell you instead of improvising.
Before we start on site
- Let building users know which areas are affected
- Tell us your opening times and when work is allowed
- Explain the parking and delivery arrangements
Get a fixed quote
Every quote starts with the facts: the joints involved, quantities, access and the product called for. Share whatever details you have and we will fill any gaps with a visit.
Related advice
Honest limits
Part of a good diagnosis is knowing where sealant stops. You’ll hear from us if the cause turns out to be one of these:
- Walls or floors that aren’t fire-resisting to begin with
- Plastic pipes whose detail calls for a collar or wrap
- Fire risk assessments, a job for a competent assessor
If in doubt, call the office on 01277 525 020 or email the details over and we will say what we think.
Surfaces we seal
- Pipe penetrations
- Service gaps in risers
- Cable penetrations
- Small duct penetrations where the tested detail allows
- Joints between fire-resisting walls and floors
- Linear gaps at wall heads
Leave it or put it right?
A seal that doesn’t match its tested detail gives false comfort. Correcting it means cutting it out and starting again with the specified product, and doing it once, properly, is cheaper. Buildings that aren’t in daily use, such as halls and seasonal premises, may let water in unnoticed, so a failed joint has time to cause damage. Resealing early avoids that.
The price depends on the quantity of joints, what has to come out first and the access. Call for a quote when you’re ready.
Why choose Mastic Doctor in Balintore
- Constructionline member for supplier checks
- A fixed quote before work starts
- Fully insured
- One phone line for London, the South East and Scotland
Take a look at our cost guide or our accreditations and insurance.
What the job involves on each surface
Linear joints
Head-of-wall gaps, slab edges and wall junctions are linear joints. Their tested detail, under BS EN 1366-4, sets the width, depth, backing and movement allowed.
Metal pipes
Metal pipes conduct heat, so their details often call for extra measures along the pipe, and some details add wrapping or a set length of insulation. We follow whatever the detail requires and flag anything we can’t match.