Felpham facade sealing
Work needed on a facade joint in Felpham? We look at it, seal it with the right product and hand it over with a 12-month guarantee.
- Previous reseals run over old sealant
- Perimeter joints where frames meet the structure
- Weathered facade joints that have lost their grip
Facade sealing for businesses in Felpham
Photos, a specification or a quick description of the joints is enough to start a fixed quote.
Cost factors for facade joints
A fixed quote reflects the actual work. It takes account of:
- How much existing material needs removing
- Which sealant the job calls for
- Backing rod, priming and other preparation
- How much there is to seal
We don’t publish prices, since every building and every scope is different. For a fixed figure, call for a quote and we will price your job on its own details.
Details that help us quote
The more we know, the firmer the quote. When you get in touch, include:
- Rough lengths or quantities, or drawings if you have them
- Your programme or deadline
- Whether an asbestos survey exists
- The site address and postcode
Specifications, drawings and tender packages are welcome with any enquiry, and we’ll price against exactly what is specified. For smaller jobs, photos and a description will do.
How we handle facade sealing in Felpham
We don’t install glazing systems or replace glass. What we seal are the joints around them: the frame-to-structure perimeter, panel-to-panel joints and window and door surrounds. Site teams most often ask us about cold air coming in at window perimeters and new sealant peeling off old mastic, on coping and flashing joints, shopfront frames and window and door perimeters. Searching for sealant specialists in Felpham? We have been sealing commercial buildings since 2005, CHAS accredited and a Constructionline member.
On a small site around Felpham, the mastic is best done in the fewest visits we can manage. Tell us when scaffold comes down and when decoration finishes, and we will plan around those stages.
We sign every job off with a 12-month guarantee. The promise is simple: if the work we did fails within twelve months, we return to fix it.
- Location
- Felpham (PO22, PO21)
- Region
- West Sussex
- Cover
- A 12-month guarantee
- Quote
- Fixed quote, scope in writing
- Phone
- 01277 525 020
- Last updated
- 3 November 2026
Facades, frames and programmes in Felpham
Felpham sits close to the coast, within about 1 mile. Coastal exposure means perimeter and cladding joints work harder than on an inland job, so joint design, primers and product choice deserve extra care. Felpham is in the South East, one of the UK’s drier regions. Still, external mastic needs dry faces within the maker’s temperature limits, which isn’t every day, so we time external mastic for dry faces and agree it with the site team.
For a contractor working at a hospital such as Bognor Regis War Memorial Hospital, which lies west of Felpham, perimeter and facade sealing is planned around patients and deliveries. When a school such as Felpham Community College is extended or refurbished, the mastic package is often squeezed into the holidays.
Felpham is about 1 mile east of Bognor Regis, in West Sussex. Businesses, contractors and managing agents in Felpham use us for work on facade joints, as part of our coverage of West Sussex. Felpham is one of 373 places we cover in West Sussex. Sites around Portsmouth have their own page, about 19 miles away.
Anyone looking for facade sealing in PO22 and PO21 gets the same process as the rest of our area: send details, get a quote, we seal, guaranteed. If your site is on Sea Road, Ley Road and Limmer Lane or close by, we can quote for facade joints. Close to Felpham, our area also takes in South Bersted (1 mile west), Flansham (1 mile north-east), Bognor Regis (1 mile west), Middleton-on-Sea (2 miles east) and Shripney (2 miles north-west). Bigger towns within reach include Worthing (11 miles east), Chichester (6 miles north-west), Selsey (7 miles south-west), Littlehampton (6 miles east), Lancing (15 miles east) and Rustington (7 miles east).
Around Felpham
Locally, jobs take us to sites close to The Brooks Local Nature Reserve, The Thatched House and Downview Primary School. The closest station to Felpham is Bognor Regis station, roughly 1 mile west of the centre. Other landmarks nearby include Bognor Regis Museum (1.2 miles south-west) and Bognor Regis War Memorial Hospital (1 mile west).
Should maintenance staff do it?
Putting right a botched joint often costs more than sealing it well at the start, since all of it has to come out and the faces be cleaned back again. That’s why many clients bring in a specialist from the beginning.
General builders and handymen seal joints, but it isn’t their main trade. A specialist prepares properly, controls joint depth and picks a product with the right movement class.
Do you need facade sealing in Felpham?
When the sealant tears down its centre, it has normally been asked to move more than it can. Too thin a bead, too narrow a joint or a product with the wrong movement class are common reasons.
Clients normally get in touch after noticing something like this:
- New sealant peeling off old mastic
- Draughts around frames and panels
- Perimeter sealant that has split or peeled away
- Weathered facade joints that have lost their grip
On a campus such as University of Chichester (Bognor Campus), less than half a mile to the west of Felpham, new teaching buildings and residences are typically built and refurbished around the academic year.
What your quote should include
- Can the work be phased to keep areas open?
- Whether primer will be used where the manufacturer specifies it
- How they handle RAMS and site documents
- Is the sealant right for the movement and the substrate?
From enquiry to sign-off
Before we leave any area, we remove the tape, clean down and inspect every joint with your site contact. Where the sealant needs time to cure before use, we tell you and sign the area. What matters most for a job in Felpham is a clear list of what needs doing. You will then get a fixed price for the work.
- We start with photos, drawings or a visit to see the joints and agree access.
- Product choice follows the joint’s movement and substrate.
- The existing bead comes out in full and the joint faces cleaned.
- Primer goes on where the product data asks for it.
- Backing rod is fitted and the new sealant gunned in and tooled.
- We go over the completed work with you before leaving.
Before we start on site
- Tell us which areas need to stay in use
- Have the specification and drawings to hand
- Point out parking and an unloading spot
Request a quote
Send us photographs, drawings or a joint schedule are often enough for a fixed quote. If the job needs a look first, we will arrange a site visit.
Related advice
Building owners, agents and FMs in Felpham
If you look after buildings for someone else, clear figures and clear communication matter. We quote a fixed sum, confirm the scope and walk the finished work with you or your representative, plus a 12-month guarantee.
Blocks and communal areas make up much of the work for housing associations and agents. Work can be phased so residents and staff keep access throughout, and each stage is agreed with your contact.
Nearby places to Felpham
More services for Felpham
Your questions answered
Is Felpham too small for you to travel to?
Not at all: smaller places are covered as well as towns. We cover Greater London and the counties of the South East. Send photos and a list of what needs doing, and we will plan the job to need as few trips as possible.
Can you work around term dates at a campus such as University of Chichester (Bognor Campus)?
Yes. We plan campus work around teaching, exams and residence turnarounds. We are CHAS accredited and a Constructionline member, and paperwork such as RAMS is confirmed with the quote.
Is any job too small?
Small jobs are welcome alongside larger packages. Photos and a description are enough to start.
Which sealant do you use on facades?
Most facade and window perimeter joints take a low-modulus neutral-cure silicone. Hybrid or MS polymer, polyurethane and polysulphide sealants suit others, depending on the substrate and the specification.
Does weather matter for sealant work?
It can, when the joints are outside. Wet joints and cold, damp or frosty conditions stop the sealant bonding properly, so we watch the forecast and rearrange outside work if we have to. Indoors, the weather is rarely a problem.
What’s the quickest route to a quote?
The quote form is the simplest route, though you can also call 01277 525 020 or email the details over. Include photographs or drawings if you have them.
Can you look at water coming in around a frame?
Yes. We check the sealant joints and report what we find as part of pricing. If the water seems to come from a roof, sill or the glazing unit instead, we say so.
Looking after the joints
After handover, these steps help:
- Keep pressure washers away from fresh sealant
- Combine resealing with other works that need access
- Record the product and colour used on each elevation
- Ask about asbestos in pre-2000 mastic
After heavy weather, check vulnerable elevations for signs of water inside. Catching a new leak early keeps the repair small.
Use each reseal to correct the joint: correct depth, proper backing and a sealant that can take the movement. Repeating a faulty detail just repeats the failure.