Expansion Joint Sealing in Bankfoot
Our CSCS-carded applicators take on expansion and movement joint sealing in walls, decks and floors in Bankfoot and the surrounding area. Send photos or drawings for a fixed quote.
- Water getting into the wall through a failed joint
- Joints where the bead has lost adhesion
- Expansion joints filled with dirt and stones
Expansion joint sealing in Bankfoot
Share the site address and what’s failing, and we’ll reply with a fixed quote or arrange a visit.
Expansion joint sealing in Bankfoot, done properly
A movement joint only works while its seal does. When the sealant splits or lets go, the gap fills with dirt and water; the joint jams, its edges take the load and the arrises spall. Dealt with early, it stays a sealant job rather than a concrete or masonry repair. We work on brickwork movement joints, precast concrete panel joints and blockwork control joints, and the usual reasons a site gets in touch are new sealant over old, now failing and damp inside where a wall movement joint has failed. Whether you call it commercial sealant work, mastic application or joint sealing, the work in Bankfoot is the same: the right product in a properly prepared joint.
For floor or movement joints around smaller places like Bankfoot, we plan to finish in one visit where we can. Send photographs, joint widths and details of the traffic first.
Work we carry out comes with a 12-month guarantee. Should something we installed fail, give us a call on 01277 525 020 or send details through our quote form and we will come back to it.
- Location
- Bankfoot (PH1)
- Wider area
- Perth and Kinross
- Cover
- 12 months on every job
- Quote
- A fixed quote before we start
- Telephone
- 01277 525 020
- Updated
- 3 November 2026
Bankfoot: questions and answers
Is Bankfoot too far out for you?
No. Places such as Bankfoot are covered as much as the big towns. We cover the whole of Scotland. Good photos up front let us bring everything on the first visit.
What documents will you need to give us for a job in Bankfoot?
Whatever your site asks for, from RAMS to CSCS details, is confirmed when we quote. We’re CHAS accredited and a Constructionline member, with £5m public liability insurance and CSCS-carded applicators.
How long will the joint resealing take?
The metres of joint, the access and the amount of removal decide it. Typically it takes a few hours to several weeks, depending on how many metres of joint there are and how much old sealant or filler needs removing.
What causes movement joint sealant to fail?
Most often the movement is too much for the product or the joint width. We review the joint design as well as the sealant before pricing, rather than replacing like for like.
Does weather matter for sealant work?
Outside, yes. Sealant needs a dry joint and a temperature within the product’s range, so damp, frosty or very cold days can stop external work. Inside work is seldom held up.
Do you offer coloured sealant?
It depends on the product. Some ranges are wide, others limited, so the available colours are confirmed with the quote.
Which product is best for expansion joints?
We choose a sealant with a movement capability that suits the joint as set out in BS EN ISO 11600. Hybrid or MS polymer products suit some mixed-material joints.
More services for Bankfoot
When to bring in a specialist
The visible bead is only part of the job. Backing rod, primer where specified and a joint designed to move with the building are where general trades tend to cut corners.
Redoing a failed joint normally costs more than getting it right at the outset, because the whole bead must be removed and the faces cleaned back again. That’s why many clients bring in a specialist from the beginning.
How a job runs
In a busy building, we agree a sequence with your contact so the disruption stays in one area at once. Each area is protected, prepared and sealed before the next one starts. For a building near Bankfoot, directions, keys and a contact on the day are worth sorting early. That goes into the plan alongside the quote.
- First the joints are inspected, widths measured and the type of failure noted.
- You receive a fixed quote stating the product and the movement it is rated for.
- Where areas have to stay open, we agree a phased sequence before starting.
- We strip the old sealant or filler and prepare each face until it’s sound and dry.
- Backing rod or bond-breaker sets the depth, primer goes on where specified, and the sealant is applied and tooled.
- We check each joint with you, confirm the cure time and sign off under our 12-month guarantee.
Getting the site ready
- Confirm the product named in the specification
- Let building users know which areas are affected
- Point out parking and an unloading spot
Quotes
Pricing a project or setting a maintenance budget? We will quote against your scope and drawings that you can work with. If you have questions first, speak to us on 01277 525 020 or email us.
Related advice
Commercial clients in Bankfoot
We take on planned maintenance as well as one-off repairs: working through a building or an estate in stages that fit your budget. Sites in Bankfoot can sit alongside others in a wider programme across Perth and Kinross.
If you look after buildings for someone else, clear figures and clear communication matter. We quote a fixed sum, confirm the scope and walk the finished work with you or your representative.
Where floor joints take the most wear near Bankfoot
Being in the east of Scotland, Bankfoot gets less rain than the west coast. Frost and de-icing salt still find their way into open external joints. Autumn is a sensible time to seal them.
Around Bankfoot, each joint gets a filler or sealant matched to what crosses it and how much it moves.
Bankfoot is about 7 miles north of Perth, in Perth and Kinross. Across the PH1 postcode area, the process is the same: details in, fixed quote out, then sealing and a 12-month guarantee. We work across 114 places in Perth and Kinross, large and small. We also cover Dundee, around 21 miles from Bankfoot.
If you need expansion joint sealing in PH1, the process matches everywhere else we work: details, then a fixed price, then sealing and a 12-month guarantee. Buildings on Main Street, Graham Court and Church Lane are within our area. Sites close to Bankfoot are covered too, including West Tofts (3 miles east), Stanley (3 miles south-east), Murthly (3 miles north-east), Gellyburn (3 miles north-east) and Middleton (3 miles north). Bigger towns within reach include Perth (7 miles south), Blairgowrie and Rattray (9 miles north-east), Crieff (15 miles south-west), Letham (7 miles south), Scone (7 miles south-east) and Tulloch (6 miles south).
Around Bankfoot
Bankfoot’s nearest station is Dunkeld & Birnam station, about 4.5 miles north-west. Other landmarks nearby include Murthly Castle (2.8 miles north). Not far away are Lily Loch and Birnam Hill.
Aftercare for building managers
Regular inspection catches problems early. Specifically:
- Raise snow-clearing blades over deck joints where possible
- Note which joints were done, when, and with what
- Include every elevation and deck joint in periodic inspections
- Keep racking legs and heavy point loads off floor joints
Floor joints on main traffic routes need watching more closely than the rest. Avoid standing heavy loads or racking legs on the joints, and report any chipped edges early.
External wall joints that fail let rain into the masonry and cavity. It can surface inside as damp a long way from the joint by which time the joint has been open for a while. Resealing promptly prevents internal damage.
When to call us in Bankfoot
Three-sided adhesion is a common cause of early failure. Sealant fixed to the base and sides can’t flex, so it tears.
Things that typically lead to an enquiry:
- Joints where the bead has lost adhesion
- Leaks through car park deck joints onto the level below
- Joints packed with grit and debris
- Movement joints with split or torn sealant
Once a joint near Bankfoot opens up, grit and water get in and the edges start to break; we will tell you if the edges need repairing first.
What to look for in a quote
- Will CSCS-carded applicators be on site?
- Which product they’ll use, and why it suits the joint
- Proof of insurance
- Health and safety accreditation such as CHAS
What sealant work can’t fix
Sealant solves a lot, but not everything, and we are upfront when that’s the case. These need a different solution:
- Joints too narrow for the movement, which need redesigning by the engineer
- Proprietary pre-formed expansion joint systems
- Structural movement beyond what the joints were designed for (that needs a structural engineer)
If you are not sure, just ring 01277 525 020 or email a schedule or drawings and we’ll give you a straight answer before you book.
What we seal
- Blockwork control joints
- Cladding panel joints
- Podiums and floor movement joints
- Car park decks and ramps
- Precast concrete panel joints
- Brickwork movement joints