Industrial and floor joint sealing in Hillside, Angus
Our CSCS-carded applicators take on floor joint sealing and filling in warehouses, factories and industrial units in Hillside. Send photos or drawings for a fixed quote.
- Broken arrises where pallet trucks cross
- Untidy open joints in a retail unit
- Loading bay joints breaking down
Floor joint sealing across Hillside
Send drawings, photos or a joint schedule, or tell us about the site, and we’ll come back with a fixed quote.
How we handle floor joint sealing in Hillside
Open joints take a beating from forklift and pallet-truck wheels. Every pass chips at the bare concrete edge until a crisp saw cut becomes a wide, broken groove. A properly filled joint carries the wheel over and protects both arrises. It also smooths the route for drivers and stock. If you are dealing with cracked and crumbling joint fill and unfilled floor joints collecting dirt and grit, we can put it right. For commercial sealant work in Hillside, you deal with one contact from quote to sign-off, for single jobs and planned programmes alike.
Weather windows decide external joint work around a place like Hillside: dry faces and the right temperature are essential. Internal floors can be done whenever suits the site.
We stand behind the joints we seal with a 12-month guarantee. That covers our preparation and application, and if something we did falls short, we return to it.
- Location
- Hillside (DD10)
- Region
- Angus
- Cover
- A 12-month guarantee
- Quotes
- Quoted before any work starts
- Phone
- 01277 525 020
- Last updated
- 3 November 2026
Keeping the joints sound
Regular inspection catches problems early. Specifically:
- Remind operators to lift rather than drag
- Photograph any joint that starts to chip
- Mention any aggressive cleaning regime at quote stage
- Allow for topping up joints as a new slab settles
Keep traffic off fresh joints until the time we give you and it pays to stick to it. In a busy building, barriers keep early traffic away.
Regular inspection catches failing fills before the edges go. A phased plan, worst routes first, spreads the work out and keeps on top of the rest.
Site staff or a sealant specialist?
For a quick touch-up, site staff may be fine, but larger jobs are different: a specialist works through quantities efficiently, leaves a consistent finish and backs it with a 12-month guarantee.
Some joints are best left to specialists: fire-rated seals that must follow a tested detail, trafficked floor joints and external movement joints among them. Getting these wrong normally costs more in the end than doing them right.
Also in Hillside
Do you need floor joint sealing in Hillside?
Unfilled joints soon pack with grit, shrink-wrap scraps and pallet splinters. Packed debris acts like a wedge every time a wheel crosses, speeding up the damage.
Common reasons buildings call us in:
- Joint fill separating from the concrete
- Loading bay joints breaking down
- A rough ride across broken joints
- Soft sealant dragged out of trafficked joints
Hospitals like Stracathro Hospital, 5.7 miles north-west of Hillside, have multi-storey or surface car parks whose joints carry vehicles round the clock.
Comparing quotes
- How joint depth will be controlled
- How the existing material will be dealt with
- Can the work be phased to keep areas open?
- Health and safety accreditation such as CHAS
Common questions from Hillside clients
Is Hillside too small for you to travel to?
No. Small places get the same service as large ones. Every Scottish council area is within our area. Send photos and a list of what needs doing, and we will plan the job to need as few trips as possible.
Is a hospital such as Stracathro Hospital somewhere you can work?
Yes, provided the work is planned with the site’s estates team. Each area is agreed with the ward or department and the estates team in advance.
Is it fine to apply new sealant on top of old?
No. Failed sealant is removed and the faces cleaned back to sound, dry material first, since fresh sealant will not bond reliably to aged material.
What information helps you price floor joint sealing?
Use our quote form, or email photographs and a plan and tell us what runs on the floor. We then send a fixed quote that shows the products and zones.
Who decides which product is used?
The specification comes first, if there is one. If there isn’t one, it comes down to the joint: its movement, its surfaces and what it has to cope with.
What if there’s asbestos in the old mastic?
Managing asbestos is the dutyholder’s responsibility, so we will ask for the register before work on an older building. If anything suspect turns up, we stop until it’s tested.
Is the floor joint work guaranteed?
Our workmanship carries a 12-month guarantee, and we hold public liability insurance.
Why act early in Hillside
Tape, or whatever sealant is in the stores cupboard, may look like a fix for a while. Neither is made to carry wheels and traffic soon pulls it out. A product chosen for the traffic and movement does the job once. For buildings near Hillside, dealing with all the failing joints at once saves return trips. Photos of each area help us quote the whole job.
Small jobs and large programmes are priced from the same things: scope, access, product and programme. Call for a quote and we will put a fixed figure on it.
Why appoint us
- One phone line for London, the South East and Scotland
- Fully insured, including public liability cover
- Our applicators hold CSCS cards
- Sealing commercial buildings since 2005
Read how commercial sealant jobs are priced and our accreditations and insurance.
Floor joint sealing around Hillside: points for this area
With the shore within about 2 miles, Hillside counts as a coastal location. Coastal yards and decks give their joints salt and wet weather to deal with, not just wheels, so a failed joint lets more in and the edges break up sooner. Hillside is on Scotland’s drier eastern side. Frost and de-icing salt still find their way into open external joints. Resealing before the cold months helps protect the edges.
Warehouse floors on estates like Forties Road Industrial Estate, 0.9 miles to the south-east of Hillside, carry pallet trucks and forklifts over every saw-cut joint. Across sites such as Broomfield Industrial Estate, 1.3 miles to the south-east of Hillside, floor and movement joints can be sealed in phases so units keep working.
Hillside is about 2 miles north of Montrose, in Angus. Hillside sits inside our coverage, with the same fixed quotes and 12-month guarantee as everywhere else. Our Angus coverage takes in 65 places, from busy centres to rural villages. Dundee is covered too, some 27 miles away.
Business premises anywhere in DD10 are within our area for floor joints. We cover commercial and managed buildings on Scott Crescent, Dickson Avenue and Cruickshank Park and the roads nearby. Sites close to Hillside are covered too, including Montrose (2 miles south), Craigo (2 miles north-west), Ferryden (3 miles south), Marykirk (3 miles north-west) and St Cyrus (3 miles north-east). Nearby towns on our patch include Arbroath (13 miles south), Brechin (7 miles west), Letham (14 miles south-west), Edzell (8 miles north-west) and Friockheim (10 miles south-west).
Around Hillside
The closest station to Hillside is Montrose station, roughly 2.1 miles south of the centre. Other landmarks nearby include Montrose Castle (2.5 miles south) and Stracathro Hospital (5.7 miles north-west). Open spaces near Hillside include Duns Dish and St Cyrus National Nature Reserve.
What we can’t put right
Being straight saves everyone time. New sealant won’t cure:
- Damaged or worn floor coatings and screeds
- Unstable slabs moving under traffic
- Spalled arrises, which need an edge repair first
If in doubt, speak to us on 01277 525 020 or use the quote form and we will say what we think before you book.
What we seal
- Construction joints
- Retail and showroom floors
- Saw-cut induced joints
- Forklift and pallet-truck routes
- Loading bays
- Joints along racking aisles
How a job runs
On arrival, we sign in, go through any site induction and check how permits are handled. Floors, finishes and fittings next to the joints are covered before anything is cut or cleaned, with the work itself typically taking a day for smaller units, with bigger warehouse floors programmed over several visits. Jobs near Hillside are often grouped with others in the same area, to make the most of each trip. Tell us how flexible your dates are.
- First comes a walk of the floor to record joint sizes, broken edges and traffic routes.
- You get a fixed quote with the product and the phasing set out.
- We remove failed material and packed debris until sound concrete is exposed on both faces.
- We vacuum each run and prime it if the chosen product requires a primer.
- Filler or sealant goes in to the right depth and is finished flush with the slab.
- We tell you when each zone can carry trucks again and move on to the next.
Before we start on site
- Tell us what induction or permit system the site runs
- Tell us which areas need to stay in use
- Send any specification or drawings in advance
Quotes
Quotes are fixed against the scope you send, so you know the figure before anyone is on site. To start the process, phone 01277 525 020 or email us.