Sandness fire stopping
Need fire stopping in Sandness? It’s simple: send details, get a quote, we seal, guaranteed.
- Old intumescent sealant that has split away
- Open linear gaps along the top of fire-resisting walls
- Damaged fire seals in risers and voids
Fire stopping across Sandness
Share the site address and what’s failing, and we’ll reply with a fixed quote or arrange a visit.
When to call us in Sandness
Plenty of openings were simply never closed, often hidden above suspended ceilings or behind boxing. They come to light during inspections, refits or when another trade lifts a tile.
Common reasons buildings call us in:
- Penetration schedules that need working through
- Openings left by services added after handover
- Fire sealant pulled out of the opening
- Openings found when ceilings come down for a refit
For buildings in and around Sandness, fire-rated sealant is installed where it is specified, to the manufacturer’s tested detail.
Before you book anyone
- Can the work be phased to keep areas open?
- How joint depth will be controlled
- Whether their applicators hold CSCS cards
- The terms of the workmanship guarantee
Fire stopping in Sandness
The test standards are BS EN 1366-3 for penetration seals and BS EN 1366-4 for linear joints and the results are classified to BS EN 13501-2. That classification, such as EI 60 or EI 120, belongs to the product in its tested arrangement. Reproducing the tested arrangement on site is the part we take care of. If you are dealing with open linear gaps along the top of fire-resisting walls and expanding foam used as fire stopping, we can put it right. Most enquiries from Sandness start with one failed joint and grow into a wider look at the building: we check the joints around it and give you an honest view of what needs doing now and what can wait.
For a building near Sandness, we plan fire-rated sealing so it’s finished in one visit where possible. Photos of the gaps, the services and the wall or floor type help us bring the right products.
Building owners and contractors get the same cover: a 12-month guarantee on our workmanship. It doesn’t extend to damage, faults in the building or work by others, and we’re upfront about that.
- Location
- Sandness (ZE2)
- Region
- Shetland Islands
- Cover
- 12 months on our workmanship
- Quotes
- Fixed quote, scope in writing
- Telephone
- 01277 525 020
- Last updated
- 3 November 2026
How a job runs
Where the site stays busy, we agree a sequence with your contact so the disruption stays in one area at once. Each area is protected, prepared and sealed, then reopened once the sealant allows before the next one starts. For work around Sandness, we aim for one trip, which is why we ask for photographs and a full list first. Outside work also needs a suitable weather window.
- The specification and schedule come first, so we know which details apply.
- Access, permits and the order of areas are agreed with the site team.
- We compare every service penetration with its tested detail before sealing.
- Foam, ordinary sealant and debris come out so the seal starts clean.
- Backing and fire-rated sealant are installed to the detail and tooled.
- We tell you about openings that need a different product.
Getting the site ready
- Tell us what induction or permit system the site runs
- Tell us your opening times and when work is allowed
- Clear stock, furniture or equipment away from the joints
Ask for a quote
For a fixed quote, call 01277 525 020 or use the quote form with the site address and an outline of the work. Our quote form is another easy route.
Related advice
Maintenance after handover
Regular inspection catches problems early. Specifically:
- Record which product was used where
- Report damaged or disturbed seals as soon as they’re spotted
- Ask the designer to confirm details early on refits
- Look above ceilings when tiles are lifted for other jobs
Don’t patch a fire-rated seal with anything outside its tested detail. Repairs need the same product and detail as the original unless the designer specifies otherwise.
The simplest way to keep compartment walls intact is to plan fire stopping into every job that crosses them. That way the opening is sealed while the trade and access are still there.
Other services in Sandness
Fire stopping in Sandness: the local picture
Scottish guidance (non-domestic Technical Handbook, clause 2.1.14) asks that penetrations match at least the fire resistance period of the element they pass through, and products should be tested for their end use. We install fire-rated sealant to that tested detail where it is specified. Island jobs, Sandness among them, are planned around the ferry and the forecast. The specification and photographs of each penetration let us bring the right products first time.
For a building such as St Margaret's Kirk and Graveyard, new heating or data runs are the usual reason penetrations need sealing.
Sandness is in the Shetland Islands. Sandness sits inside our coverage, with the same fixed quotes and 12-month guarantee as everywhere else. 63 places across the Shetland Islands fall within our area, Sandness among them.
We take on service penetrations across the ZE2 postcode area, whatever the building. If your building is just outside Sandness, we cover Melby (1 mile north-west), Walls (6 miles south-east), Aith (10 miles east), Easter Skeld (11 miles south-east) and Brae (12 miles north-east). Where a site is remote or on an island, travel and materials need planning ahead, so the full address helps from the start.
What’s near Sandness
The countryside around Sandness includes Loch of Norby.
How the job changes by surface
Risers and ceiling voids
Service risers and the voids above ceilings are where openings collect. Access to these areas is planned with you in advance along with any permits your site needs.
Small ducts
Ducts are only sealed with sealant where the detail allows it. Dampers and ductwork systems themselves are outside our work.
Questions we are asked in Sandness
Is Sandness inside the area you cover, given it’s on an island?
Yes. Every Scottish council area is within our area, and that includes island locations such as Sandness. We group island work where we can and plan around the crossings.
Will you design a fire-stopping scheme for our building in Sandness?
No, that sits with the designer, fire engineer or building control. We install fire-rated and intumescent sealant around service penetrations and linear gaps where it is specified, to the manufacturer’s tested detail.
Do you seal on top of existing sealant?
No. We cut the old material out and clean the joint back before sealing, since fresh sealant will not bond reliably to aged material.
Can weather delay the job?
It can, when the joints are outside. Wet joints and cold, damp or frosty conditions stop the sealant bonding properly, so we watch the forecast and rearrange outside work if we have to. Internal work is far less affected.
Can you work while the building is occupied?
In the majority of cases, yes. Phased work can be planned so areas stay in use, with each area protected and signed.
What happens if old sealant might contain asbestos?
Managing asbestos is the dutyholder’s responsibility, so we’ll ask for the register before work on an older building. If anything suspect turns up, we stop until it’s tested.
Do you need to see the site first?
That depends on the size and complexity of the job. Simple work can often be priced from photographs, while larger or less clear jobs get a site visit first.
What we can’t put right
Honesty saves time and money. New sealant won’t cure:
- Signing off or certifying a building’s fire stopping
- Plastic pipes whose detail calls for a collar or wrap
- Deciding what a wall or floor needs, which belongs to the designer
If in doubt, ring 01277 525 020 or email the details over and we’ll say what we think.
What we seal
- Joints between fire-resisting walls and floors
- Small duct penetrations where the tested detail allows
- Cable penetrations
- Linear gaps at wall heads
- Pipe penetrations
- Service gaps in risers
What happens if it’s left?
Inspections and handover checks often pick up fire stopping. Late discoveries can delay handover while openings are reopened and resealed. In Scotland, wind-driven rain finds a failed joint quickly, and for a smaller place like Sandness, a repair visit takes planning, so it’s better to act early.
The product called for affects the cost, and so does the preparation, such as cutting out, priming or new backing rod. Access, phasing and site requirements come into it too.
What you get with us
- One number for every site we cover
- Sealing commercial buildings since 2005
- Health and safety: CHAS accredited
- Specification-led, product-correct work
Take a look at what affects the cost and how we’re accredited.