Facade Sealing in Sandness
Looking for facade sealing in Sandness? Send us the details for a fixed quote, backed by a 12-month guarantee on the work.
- Facade joints cracked through the middle
- Old perimeter mastic that has dried out
- Unsightly perimeter sealant on a visible elevation
Facade sealing near Sandness
Photos, a specification or a quick description of the joints is enough to start a fixed quote.
Facade sealing around Sandness: how the place shapes the job
The sea is no more than about 1 mile from Sandness. Schemes this close to the sea see their facade joints tested by wind and rain from the day they’re sealed, and the sealant, primer and backing need choosing with that in mind. Scotland has its own building regulations, and in Sandness warrants come from the local authority verifier. The mastic package follows the approved specification.
On any site in or around Sandness, the mastic follows the specification and the programme. Around Sandness, as anywhere, a facade joint depends on its sizing, backing rod and preparation.
Sandness is in the Shetland Islands. If you’re looking for facade sealing in Sandness, we can help, as we do across the Shetland Islands. We work across 63 places in the Shetland Islands, from busy centres to rural villages.
Business premises anywhere in ZE2 are within our area. Close to Sandness, our area also takes in Melby (1 mile north-west), Walls (6 miles south-east), Aith (10 miles east), Easter Skeld (11 miles south-east) and Brae (12 miles north-east). Remote and island addresses take more planning, from travel and ferries to the weather, so mention the location when you call 01277 525 020 or send details through our quote form.
What’s near Sandness
Not far away are Loch of Norby.
Facade sealing in Sandness
Facade sealants sit in the sun, rain and frost every day. How long a joint lasts depends on the movement it takes, its exposure, the product and how well it was installed. When the time comes, we cut the old sealant out completely and start again. If you’re dealing with hard, chalky sealant that no longer flexes and cold air coming in at window perimeters, we can put it right, on coping and flashing joints, perimeter joints where frames meet the structure and cladding panel joints alike. A specialist sealant contractor works differently from a general builder: in Sandness, that means joint design, primers and backing rod as standard.
Sites near smaller places like Sandness can mean longer travel, so the mastic is planned with as few trips as the job allows. Send drawings, photographs and the programme so everything needed arrives on the first day.
Our workmanship is guaranteed for 12 months. If a joint we sealed fails because of how it was installed, we come back and put it right.
- Location
- Sandness (ZE2)
- Region
- Shetland Islands
- Cover
- 12 months on our workmanship
- Price
- Quoted before any work starts
- Telephone
- 01277 525 020
- Page updated
- 3 November 2026
Also in Sandness
Should maintenance staff do it?
Putting right a botched joint often costs more than sealing it well at the start, since all of it has to come out and the faces be cleaned back again. That’s why many clients bring in a specialist from the beginning.
There’s also the paperwork. Many sites expect CSCS cards, RAMS and proof of insurance, and we will confirm the paperwork you need with the quote.
Why act early in Sandness
Leaving failed perimeter sealant also makes the eventual job bigger: wet edges break down, so repairs may be needed before resealing. Early action keeps it simple. Renewing every failing joint on one visit is the sensible approach for a place like Sandness. Send photographs and we will quote for everything together.
Small jobs and large programmes are priced from the same things: scope, access, product and programme. Call for a quote and we will put a fixed figure on it.
Why us?
- Constructionline member for supplier checks
- One contact handling all your sites
- Work to your specification and the manufacturer’s guidance
- Fully insured
Take a look at our cost guide or our accreditations and insurance.
Common questions from Sandness clients
Is Sandness inside the area you cover, given it’s on an island?
Yes, Sandness is within the area we cover. We work across every Scottish council area. We plan island jobs around the ferry and the forecast, and bring everything the job needs on the first crossing.
Our building in Sandness is near the coast: does that change the sealant?
It can. Wind-driven rain and, closer to the shore, salt air are harder on external joints. We choose the product for the exposure, prime where the manufacturer requires it and size the joint for its movement.
What’s the quickest route to a quote?
The quote form is the simplest route, though you can also call 01277 525 020 or email the details over. Photos, drawings or a joint schedule help us quote quickly.
Do you use silicone for external joints?
Most facade and window perimeter joints take a low-modulus neutral-cure silicone. Hybrid or MS polymer, polyurethane and polysulphide sealants suit others, as the specification or substrate requires.
Can you find out why a window is leaking?
Yes. We look at the perimeter sealant and tell you whether it has failed before quoting. Where the cause seems to be elsewhere, we’d rather tell you than reseal pointlessly.
Are your applicators CSCS-carded?
Yes. We use CSCS-carded applicators, as many construction sites ask for.
Is it fine to apply new sealant on top of old?
No, never. Sealing over old material is one of the classic causes of early joint failure, so it all comes out first.
Different surfaces, different methods
Precast concrete panels
Precast arrises sometimes crumble or carry old residue. We clean back to sound material and flag edges that need repair first.
Window and door perimeters
Aluminium, PVC-U and timber frames each have their own preparation needs. Primer goes on where the manufacturer specifies it for that substrate.
Diagnose, treat, sign off
Our CSCS-carded applicators arrive with the sealants, primers and backing rod the job calls for. Joint faces are cleaned back to sound, dry surfaces, primer goes on where the manufacturer specifies it, and the sealant is tooled off neatly. Travel to smaller Scottish places like Sandness is planned so the job is finished in one visit where possible, so photographs, sizes and a full list matter. External joints need a dry spell as well.
- Photos, drawings or a visit tell us about the joints and the access.
- Product choice follows the joint’s movement and substrate.
- Failed beads are removed in full and both faces cleaned back.
- Primer is applied where the maker specifies it.
- Backing rod is fitted and the new sealant gunned in and tooled.
- The finished joints are checked with you.
Before we start on site
- Make sure the joints can be reached
- Share the asbestos register for older buildings
- Share your working hours and any access restrictions
Get a fixed quote
Every quote starts with the facts: what’s there, how much of it, how we reach it and what’s specified. Send what you have, and we will arrange a site visit if anything is unclear.
Read more
Cost factors for facade joints
The price varies from site to site. It mainly depends on:
- Distance, for remote addresses
- Site requirements such as inductions and permits
- How accessible the joints are
- Joint width, depth and condition
We don’t publish prices, since every building and every scope is different. For a fixed figure, call for a quote and we will price your job on its own details.
What we need to price the job
A few photos plus some basic facts will normally do. Please tell us:
- Rough lengths or quantities, or drawings if you have them
- Any dates the work must fit around
- How the joints are reached, and at what height
- The site address and postcode
To get a fixed quote, call the office on 01277 525 020 or use the quote form, telling us the site location and the nature of the job. You can also send details through our quote form.
Looking after the joints
A few simple habits keep the new joints working:
- Report water ingress at frames as soon as it shows
- Never let anyone seal over old sealant
- Walk the elevations once or twice a year
- Confirm the survey covers external sealants in older buildings
If new signage, brackets or services are fixed through a sealed joint, the seal needs making good. Ask the installer to reseal it properly with a compatible product.
Get the joint design right when resealing: the right width, backing rod and a sealant with enough movement capability. Repeating a faulty detail just repeats the failure.