Fire stopping in New Luce
Need fire stopping in New Luce? Send us the details for a fixed quote, backed by a 12-month guarantee on the work.
- Seals that don’t match their tested detail
- Seals disturbed by maintenance and left open
- Builders’ foam or ordinary silicone in compartment walls
Fire stopping in New Luce
Photos, a specification or a quick description of the joints is enough to start a fixed quote.
Diagnose, treat, sign off
A typical day starts with protection: tape along each joint edge and covers over finishes, stock and equipment close by. On site, the work typically takes anything from one day to a planned run of visits, depending on the number of seals and the access, and we clear our waste as we work. Where we can, we combine work around New Luce with other jobs nearby, to make the most of each trip. Tell us how flexible your dates are.
- First we confirm the product and tested details named in the specification.
- Openings are measured and grouped by detail.
- Old or wrong materials are cut out.
- Where the detail needs backing, it goes in at the stated depth.
- We gun the sealant in to the specified depth around each service and tool it.
- Completed areas are checked with you, with the records agreed when we quoted.
Before we start on site
- Clear stock, furniture or equipment away from the joints
- Warn occupants and staff about the work
- Agree which areas must stay open
Request a quote
Send us photos, drawings or a joint schedule are often enough for a fixed quote. If the job needs a look first, we will arrange a site visit.
Advice
Fire stopping in New Luce
No fire sealant works on its own: its test evidence covers one product in one kind of wall or floor, with set services, gaps, depths and backing. Before we seal anything, we check the opening against the detail it is meant to follow, and we say so if it doesn’t fit. We work on small duct penetrations where the tested detail allows, cable penetrations and service gaps in risers, and the usual reasons a site gets in touch are fire seals cut back for extra cables and never reinstated and unsealed openings around new pipes and cables. Facilities teams, main contractors and managing agents in New Luce tend to want the same three things: a clear scope, tidy work and joints that don’t fail again.
Travel to smaller places like New Luce is planned so every penetration is sealed on one trip. Send the specification and photos of the openings, with sizes if you have them.
Every job ends the same way: guaranteed. You get a 12-month guarantee on our workmanship, and we explain exactly what that covers when we quote.
- Location
- New Luce (DG8)
- Region
- Dumfries and Galloway
- Cover
- 12 months on our workmanship
- Quote
- Fixed quote, scope in writing
- Telephone
- 01277 525 020
- Last updated
- 3 November 2026
Also near New Luce
What else we do in New Luce
Common problems we fix in New Luce
When a seal departs from its tested detail, the evidence no longer covers it. Gaps beyond the tested size, shallow sealant, no backing where it was needed, or products from different systems mixed together are what we find most often.
Typical triggers for a call:
- Unsealed penetrations discovered above suspended ceilings
- Snag lists that include open service penetrations
- Seals that don’t match their tested detail
- Builders’ foam or ordinary silicone in compartment walls
For any site around New Luce, we work to the specification and the manufacturer’s installation guidance, leaving design and sign-off with the designer.
What to look for in a quote
- Who will actually carry out the work
- Whether old or failed sealant will be cut out, not overlaid
- Is the sealant right for the movement and the substrate?
- How joint depth will be controlled
What happens if it’s left?
Fire stopping is a regular point raised at inspections and handover. Finding unsealed or improvised openings late can hold up a programme, so earlier action pays back. Exposed buildings in Scotland take a lot of weather, so it’s worth renewing joints around New Luce before they leak.
Access often affects the price as much as the sealing: easy-to-reach joints are quicker than those that need equipment to get to. Tell us how the joints are reached and call for a quote.
Why clients in New Luce choose us
- Work to your specification and the manufacturer’s guidance
- A fixed quote before work starts
- Constructionline member for supplier checks
- Work carried out by CSCS-carded applicators
See what affects the cost and our accreditations.
What sealant work can’t fix
We seal joints; we don’t mend everything behind them. Sealant alone won’t deal with:
- Designing or specifying fire stopping, which sits with the designer or fire engineer
- Plastic pipes whose detail calls for a collar or wrap
- Gaps in walls that were never built as compartment walls
Not sure which it is? You can speak to us on 01277 525 020 or send photos by email and we will tell you honestly.
What we seal
- Cable penetrations
- Linear gaps at wall heads
- Joints between fire-resisting walls and floors
- Service gaps in risers
- Small duct penetrations where the tested detail allows
- Pipe penetrations
New Luce: questions and answers
Which Scottish guidance covers penetration seals in New Luce?
The non-domestic Technical Handbook, clause 2.1.14, expects a penetration to keep at least the wall or floor’s fire resistance period, with proprietary products tested for the use they’re put to. Design sits with the designer and the verifier; installation to the tested detail is our part.
Can you produce the fire-stopping design for a job in New Luce?
No, that sits with the designer, fire engineer or building control. We install fire-rated and intumescent sealant around service penetrations and linear gaps where it is specified, to the manufacturer’s tested detail.
Does weather matter for sealant work?
It can, for external work. Sealant won’t bond properly to a wet or frosty joint, so we watch the forecast and rearrange outside work if we have to. Internal work is far less affected.
How long does a typical visit take?
It depends on the scope, though a typical visit usually takes a single visit for a short list of penetrations, or a phased programme for a whole building. For bigger or phased jobs, we will set out a timescale with the quote.
Can you follow the specification on our project?
Yes. We follow the specification, along with the manufacturer’s installation guidance.
What do you charge?
Every job gets its own fixed quote. For yours, phone 01277 525 020 or use the quote form.
What’s the quickest route to a quote?
You can use the quote form on this site; alternatively, ring 01277 525 020 or email drawings and photos. Include photos or drawings if you have them.
Fire stopping around New Luce: what changes locally
Scotland has its own building standards: the non-domestic Technical Handbook (clause 2.1.14) says service penetrations should be fire stopped to at least the fire resistance duration of the wall or floor, with products tested for that end use. Where fire-rated sealant is specified, that’s what we install, to the tested detail.
Buildings near New Luce get the fire-rated product that’s specified, installed to its tested detail.
New Luce is about 8 miles east of Stranraer, in Dumfries and Galloway. Any commercial site in New Luce is covered, whether it’s a single job or part of a planned programme. Across Dumfries and Galloway, 139 places are covered, New Luce among them. Our Glasgow page has more on work in that area.
Work on service penetrations is covered throughout DG8, whatever the building. If your site is on Main Street, Station Road and Smithy Lane or close by, send details and we’ll quote for service penetrations. Nearby places we also cover include Dunragit (5 miles south), Glenluce (5 miles south), Castle Kennedy (5 miles south-west), Innermessan (6 miles west) and Aird (6 miles south-west) for service penetrations. A short drive away, we cover Stranraer (8 miles west), Newton Stewart (15 miles east), Portpatrick (13 miles south-west) and Minnigaff (15 miles east).
Local landmarks in New Luce
Well-known places in the area include Lochinch Castle (4.6 miles south-west). Not far away are Artfield Fell and Black Loch.
After the work
Your facilities or cleaning team can help the joints last. Pass these on to them:
- Report damaged or disturbed seals as soon as they’re spotted
- File the specified details where the next contractor can find them
- Make fire stopping part of every scope that crosses a fire-resisting wall
- Include service cupboards in routine inspections
Don’t patch a fire-rated seal with anything outside its tested detail. A repair should use the original product, installed the same way unless the designer specifies otherwise.
The simplest way to keep compartment walls intact is to plan fire stopping into every job that crosses them. Then the seal goes in while the area is open instead of being left for someone else.
How the quote is worked out
To price the job, we consider:
- Whether the work must be split into stages
- The product specified
- The total length or number of joints
- Removal of failed or old sealant
The specified product makes a difference, as does the preparation each joint needs, such as cutting out, priming or new backing rod. Access, phasing and site rules also count.
What we need to price the job
Diagnosis starts before we arrive. Let us know:
- Anything awkward about access or site hours
- Specification clauses that apply
- Any dates the work must fit around
- Where the site is, with the postcode
For a fixed quote, speak to us on 01277 525 020 or email us. Our quote form is another easy route.