Fire-rated sealing and fire stopping in Aird, Dumfries and Galloway
Fire stopping for Aird, from a contractor working since 2005. Fully insured and CHAS accredited.
- Service penetrations left open after M&E works
- Fire-stopping items raised at inspection or handover
- Damaged fire seals in risers and voids
Fire stopping in Aird
Tell us what needs sealing and where, with photos or drawings if you have them, and we’ll price it.
Fire stopping for commercial buildings in Aird
On a fit-out or refurbishment, we follow the services contractors floor by floor. We work from your penetration schedule or marked-up drawings. Tell us what records you need and we’ll confirm with the quote. Most enquiries involve unsealed openings around new pipes and cables and unsealed joints where partitions meet the slab, on small duct penetrations where the tested detail allows, linear gaps at wall heads and service gaps in risers. Most enquiries from Aird start with one failed joint and grow into a wider look at the building: we look at the rest while we are there and tell you what we find.
Hotels and care homes around smaller places like Aird often have services added during refurbishment. We fit the specified fire-rated sealant as its published detail shows and raise it if another product is needed.
Our workmanship is guaranteed for 12 months, in Aird as everywhere else we work. If our installation lets you down in that time, we return and fix it.
- Place
- Aird (DG9)
- Region
- Dumfries and Galloway
- Cover
- 12 months on our workmanship
- Quote
- Quoted before any work starts
- Phone
- 01277 525 020
- Last updated
- 3 November 2026
What we can’t put right
Before quoting, we check that sealant is the right answer. It isn’t the answer for:
- Deciding what a wall or floor needs, which belongs to the designer
- Fire doors, dampers or other fire safety equipment
- Construction that lacks the fire resistance the seal relies on
Not sure which it is? You can phone 01277 525 020 or email drawings and photos and we’ll tell you honestly before you book.
Surfaces we seal
- Service gaps in risers
- Small duct penetrations where the tested detail allows
- Joints between fire-resisting walls and floors
- Cable penetrations
- Pipe penetrations
- Linear gaps at wall heads
Common problems we fix in Aird
When a seal departs from its tested detail, the evidence no longer covers it. Gaps beyond the tested size, shallow sealant, no backing where it was needed, or products from different systems mixed together are the usual culprits.
Common reasons buildings call us in:
- Fire sealant pulled out of the opening
- Snag lists that include open service penetrations
- Builders’ foam or ordinary silicone in compartment walls
- Improvised or mixed-product fire seals
For a site team at a college like Dumfries & Galloway College - Stranraer Campus, 2.1 miles west of Aird, fire-rated sealing is best scheduled after the summer works.
Comparing quotes
- Whether old or failed sealant will be cut out, not overlaid
- Will CSCS-carded applicators be on site?
- Which product they’ll use, and why it suits the joint
- Their public liability cover
What happens if it’s left?
An unsealed opening affects more than fire safety: they also carry noise, draughts and smells between rooms. Sealing them to the specified detail deals with the fire risk first. Buildings that aren’t in daily use, such as halls and seasonal premises, may let water in unnoticed, giving water time to get in. Early resealing prevents it.
Larger quantities, tricky access or phasing all shape the price. So do site requirements such as inductions and permits, along with the time of year for external work.
What you get with us
- CSCS-carded applicators
- Over 20 years of commercial sealing
- Public liability insurance in place
- Failed material removed, not covered up
See our cost guide and our accreditations.
Places near Aird
Also in Aird
Cost factors for service penetrations
These are the things that shape the price:
- Distance, for remote addresses
- The site’s rules and procedures
- Working within restricted access windows
- Whether old sealant has to be cut out first
No two sites price the same: joint size, product, access and site hours all play a part. Send the details and a fixed figure follows.
Sending details for a quote
It doesn’t need to be a full survey. A few details are enough to get going:
- Any dates the work must fit around
- Specification clauses that apply
- What the building is and how it’s used
- Anything awkward about access or site hours
Every quote starts with the facts: the joints involved, quantities, access and the product called for. Share whatever details you have and we will fill any gaps with a visit.
Keeping the joints sound
Keep the joints in good shape with a few simple steps:
- Brief every trade that openings they make must be sealed
- Arrange inspection before areas are covered up
- Treat an open penetration as a priority repair
- Ask which product is in place before decorating
Once the seals are in, tell other trades they exist and must not be disturbed. Any seal cut back for a new service needs reinstating to its tested detail using the same product.
The simplest way to keep compartment walls intact is to plan fire stopping into every job that crosses them. That way the opening is sealed while the trade and access are still there.
Our process
Our CSCS-carded applicators arrive with the sealants, primers and backing rod the job calls for. Any old material is cut back to clean, sound faces, primer goes on where the manufacturer specifies it, and the sealant is tooled off neatly. Travel to smaller Scottish places like Aird is planned so the job is finished in one visit where possible, which is why we ask for photos and a full list first. Outside work also needs a suitable weather window.
- We start with your penetration schedule, drawings or specification.
- We plan the sequence of floors, risers and voids with you.
- Each opening is checked for wall or floor type, service, gap and depth.
- Unsuitable material is removed and the opening cleaned.
- Backing and fire-rated sealant are installed to the detail and tooled.
- Anything outside the detail is reported to you rather than sealed.
Preparing the site
- Move anything stored against the joints
- Point out parking and an unloading spot
- Let us know about inductions and permits
Request a quote
The quickest route to a quote is a few photos and the site postcode. Upload them with the quote form, or call the office on 01277 525 020 or email drawings and photos if you’d rather talk the job through.
Related advice
Penetration seals near Aird
Under the Scottish non-domestic Technical Handbook, clause 2.1.14, penetrations should be fire stopped to at least the wall or floor’s fire resistance duration, and products should be tested for their end use. Where fire-rated sealant is specified, that’s what we install, to the tested detail. The area within 2 miles of Aird holds several hotels. Hotels are divided into compartments, and refurbishments that add pipes and cables through bedroom and corridor walls leave gaps to close.
Theatres, wards and plant rooms at sites like Galloway Community Hospital, 2 miles west of Aird, all have compartment walls crossed by services. In a building such as Old Parish Church and Burial-ground, any service penetration through a fire-resisting wall should be sealed to the specified detail.
Aird is about 2 miles east of Stranraer, in Dumfries and Galloway. We send applicators to Aird for service penetrations. Across Dumfries and Galloway, 139 places are covered, Aird among them. For work in that direction, see our Glasgow page (71 miles or so).
Business premises anywhere in DG9 are within our area. We also cover Lime Kiln (1 mile south-west), Castle Kennedy (1 mile east), Innermessan (2 miles north-west), Stranraer (2 miles west) and Lochans (3 miles south-west) for service penetrations.
What’s near Aird
Aird’s nearest station is Stranraer station, roughly 2.2 miles west of the centre. A little further out are Stranraer Museum (2.3 miles west) and Galloway Community Hospital (2 miles west). Not far away are White Loch.
FAQs: Aird
How do Scotland’s building standards affect fire-rated sealant in Aird?
The non-domestic Technical Handbook, clause 2.1.14, expects a penetration to keep at least the wall or floor’s fire resistance period, with proprietary products tested for the use they’re put to. Design sits with the designer and the verifier; installation to the tested detail is our part.
Is Aird off your patch?
Not at all: smaller places are covered as well as towns. Every Scottish council area is within our area. We plan jobs in smaller places so return trips are kept to a minimum.
How much does the work cost?
We don’t publish prices, as every site differs. Send photos or drawings and we will price it at a fixed figure.
Can you quote from photographs?
It depends on the job. Straightforward work can often be priced from photos and measurements, and bigger or more complex jobs usually get a visit.
What happens if old sealant might contain asbestos?
Some older mastics, especially in pre-2000 buildings, can contain asbestos. We check the asbestos register before cutting out old sealant in an older building, and if asbestos is suspected, work stops until it’s tested. Removing asbestos is a job for asbestos specialists, not us.
Do you offer coloured sealant?
In many cases, yes. Sealants are made in a wide range of standard colours, and matching to RAL references or nearby finishes is commonly requested. We will confirm the colours available for the specified product.
How do you choose the sealant?
A specification, where there is one, decides it. Without one, the joint decides: how much it moves, what it bonds to and whether it’s wet, trafficked or fire-rated.