Fire Stopping in Inverurie
Our CSCS-carded applicators take on fire-rated and intumescent sealing of service penetrations and linear gaps in Inverurie. Send photos or drawings for a fixed quote.
- Improvised or mixed-product fire seals
- Fire sealant pulled out of the opening
- Expanding foam used as fire stopping
Fire stopping in Inverurie
Tell us what needs sealing and where, with photos or drawings if you have them, and we’ll price it.
Looking after the joints
To get the most from the new sealant:
- Check with the data sheet before painting over fire sealant
- Record which product was used where
- Agree the fire-stopping specification before services go in
- Treat an open penetration as a priority repair
New services after handover are a common way fire stopping gets breached. A short check at the end of each job saves a long hunt later.
Looking at service areas on a regular cycle pays off. Catching a damaged seal early keeps the fix small.
About our fire stopping in Inverurie
We should be clear about what we do and don’t do. Deciding the specification sits with the designer, the fire engineer and building control. What we bring is careful installation of the specified sealant, to the maker’s guidance in Inverurie and nearby. If you’re dealing with seals disturbed by maintenance and left open and expanding foam used as fire stopping, we can put it right, on cable penetrations, joints between fire-resisting walls and floors and service gaps in risers alike. Most enquiries from Inverurie start with one failed joint and grow into a wider look at the building: we look at the rest while we are there and tell you what we find.
In a town like Inverurie, who decides the fire-stopping detail matters: design and sign-off sit with the designer, fire engineer or the local authority verifier, and we install what is specified. Records of the work can be discussed when we quote.
We stand behind the joints we seal: 12 months, guaranteed. That covers our preparation and application, and if something we did falls short, we return to it.
- Location
- Inverurie (AB51)
- Wider area
- Aberdeenshire
- Cover
- 12 months on every job
- Price
- Quoted before any work starts
- Call
- 01277 525 020
- Last updated
- 3 November 2026
FAQs: Inverurie
Can you seal around new services in a hotel near Inverurie?
Yes, to the specification and the product’s tested detail. We match the product to the wall or floor and the services, and say if something other than sealant is needed.
Do you take on work at healthcare sites like Inverurie Hospital?
Yes, healthcare and care buildings are part of our work. The estates team’s permit system and infection-control rules come first, and the work is planned around them.
How much does the work cost?
Each job is quoted on its own details. For yours, phone 01277 525 020 or send details through our quote form.
Can one quote cover more than one building?
Yes. Multi-site work and planned programmes are a core part of the service, with each site phased to suit its occupants.
Can you work while the building is occupied?
In the majority of cases, yes. Phased work can be planned so areas stay in use, with each area protected and signed.
Do your applicators hold CSCS cards?
Yes. We use CSCS-carded applicators.
Do you hold CHAS accreditation?
Yes. We are CHAS accredited and a Constructionline member, which helps with supplier vetting.
Fire stopping around Inverurie: what changes locally
The 2 miles around Inverurie include two care or nursing homes. Where new services have gone through compartment walls in a care setting, the gaps need the specified product. Where that’s fire-rated sealant, we install it to the manufacturer’s tested detail. In Scotland, clause 2.1.14 of the non-domestic Technical Handbook expects service penetrations to keep at least the fire resistance duration of the wall or floor, with products tested for that end use. We install fire-rated sealant to that tested detail where it is specified.
Theatres, wards and plant rooms at sites like Inverurie Hospital, 0.8 miles south of Inverurie, all have compartment walls crossed by services. For a unit at a site such as Inverurie Retail Park, less than half a mile to the east of Inverurie, any new service through a fire-resisting wall should be sealed to the tested detail.
Inverurie is about 14 miles north-west of Aberdeen, in Aberdeenshire. Commercial clients in Inverurie use us for work on service penetrations, as part of our coverage of Aberdeenshire. Our Aberdeenshire coverage takes in 179 places, large and small. For work in that direction, see our Aberdeen page, about 14 miles away.
Postcode districts covered here: AB51 for service penetrations. If your site is on West High Street, Station Road and Versatile Square or close by, we can quote for service penetrations. Being close to the A96 and B993, Inverurie is straightforward for us to reach. Just outside Inverurie, we also work in Garioch (1 mile south-east), Port Elphinstone (1 mile south-east), Kinmuck (3 miles south-east), Cottown (4 miles south) and Kintore (4 miles south). Bigger towns within reach include Westhill (10 miles south), Ellon (13 miles north-east), Kemnay (4 miles south-west), Oldmeldrum (4 miles north-east), Alford (13 miles west) and Newmachar (7 miles east). As one of the bigger centres in Aberdeenshire, Inverurie has a broad mix of commercial, public and industrial buildings, and we cover them all. Where a site is remote or on an island, we plan travel and materials carefully, so the full address helps from the start.
Local landmarks in Inverurie
In Inverurie, that means premises near The Gordon Highlander pub, among other places. There’s a railway station in Inverurie itself: Inverurie station. Nearby you will also find Garioch Heritage Centre (under half a mile east) and Pitcaple Castle (3.7 miles north-west). Open spaces near Inverurie include Scroggie Hill.
What we can’t put right
Part of a good diagnosis is knowing where sealant stops. We’ll tell you if the real problem is one of these:
- Gaps in walls that were never built as compartment walls
- Approving the work on behalf of building control
- Fire doors, dampers or other fire safety equipment
If in doubt, ring 01277 525 020 or email a schedule or drawings and we’ll say what we think.
Surfaces we seal
- Small duct penetrations where the tested detail allows
- Service gaps in risers
- Joints between fire-resisting walls and floors
- Linear gaps at wall heads
- Pipe penetrations
- Cable penetrations
What else we do in Inverurie
From enquiry to sign-off
Occupied buildings need a little choreography. The work area is signed and kept contained, with routes through the building left open and move on in phases so staff and visitors can carry on around us. For a unit on an estate in Inverurie, tell us about yard access and site rules. Central premises can need a little more planning for parking.
- We ask for the product and detail your designer has specified.
- Openings are measured and grouped by detail.
- Improvised fillers and failed sealant are removed.
- Where the detail needs backing, it goes in at the stated depth.
- Fire-rated or intumescent sealant goes in around the services and is tooled off.
- We walk the completed areas with you and confirm the records agreed at quote stage.
What we need from you
- For older buildings, check the asbestos register before work
- Flag any permit to work we will need
- Explain the parking and delivery arrangements
Get a fixed quote
A handful of photographs and a postcode is the fastest way to a quote. Upload them with the quote form, or phone 01277 525 020 or email drawings and photos to discuss it first.
Advice
Do you need fire stopping in Inverurie?
A common fault is a product that was never fire-rated in the first place: expanding foam or a general-purpose sealant pushed into a gap to tidy it. The opening looks sealed but has no fire test evidence behind it and has to be removed.
Typical triggers for a call:
- Old intumescent sealant that has split away
- Penetration schedules that need working through
- Unsealed penetrations discovered above suspended ceilings
- Damaged fire seals in risers and voids
For a school such as Inverurie Academy, penetration sealing fits best at the end of the summer works.
What to look for in a quote
- Whether primer will be used where the manufacturer specifies it
- Who will actually carry out the work
- Health and safety accreditation such as CHAS
- Their plan for phasing and protecting the area
Surface by surface
Risers and ceiling voids
Openings above suspended ceilings are easy to miss. We follow your schedule area by area and tell you about openings outside the list.
Masonry and concrete
Block walls and concrete floors are common substrates for penetration seals. Dust and loose debris are cleared out of the opening, so the sealant and any backing sit properly.
Doing it in-house
For most general trades, sealant is a sideline. A specialist brings correct preparation, depth control with backing rod and a product suited to that particular joint, which is what makes a joint last.
Certain joints really need a specialist: for instance fire-rated seals that must match a tested detail, trafficked floor joints and external movement joints. A poor seal in places like these tends to cost more to put right later.