Fire-rated sealing and fire stopping in Garve, Highland
We carry out fire-rated and intumescent sealing of service penetrations and linear gaps in Garve and the surrounding area. Send photographs or drawings for a fixed quote.
- Builders’ foam or ordinary silicone in compartment walls
- Snag lists that include open service penetrations
- Unsealed openings around new pipes and cables
Fire stopping for businesses in Garve
Photos, a specification or a quick description of the joints is enough to start a fixed quote.
Fire stopping in Garve, done properly
Most of our fire stopping work happens after the building is up. New cable runs, replaced pipework and extra data routes all punch holes in compartment walls, often unnoticed. We close the openings listed on your schedule, using the specified sealant and detail. We work on joints between fire-resisting walls and floors, cable penetrations and linear gaps at wall heads, and the failures we’re asked to look at most are damaged fire seals in risers and voids and penetration schedules that need working through. Facilities teams, main contractors and managing agents in Garve tend to want the same three things: a fixed quote, no surprises on site and a 12-month guarantee behind the result.
Refurbishments in small hotels, schools and care homes around places like Garve can leave gaps around new services. A round of checks after M&E work is good practice, and any gaps found are sealed where fire-rated sealant is specified.
We stand by our work: 12 months, guaranteed. That covers our preparation and application.
- Where
- Garve (IV23)
- Wider area
- Highland
- Guarantee
- 12 months on every job
- Quote
- Fixed quote, scope in writing
- Call
- 01277 525 020
- Last updated
- 3 November 2026
Signs you need fire stopping in Garve
Plenty of openings were simply never closed. Inspections, refurbishments and ceiling access usually bring them to light.
What tends to prompt an enquiry:
- Openings found when ceilings come down for a refit
- Head-of-wall gaps with no fire seal
- Damaged fire seals in risers and voids
- Penetration schedules that need working through
For buildings in and around Garve, fire-rated sealant is installed where it is specified, to the manufacturer’s tested detail.
What to look for in a quote
- Will failed sealant be removed rather than covered?
- How the joint faces will be prepared and primed
- How joint depth will be controlled
- How long is the guarantee, and what does it include?
How the job changes by surface
Small ducts
We seal around ducts only within what the tested detail covers. Dampers and ductwork systems themselves are outside our work.
Risers and ceiling voids
Service risers and the voids above ceilings are where openings collect. Access to these areas is planned with you in advance.
Nearby places to Garve
What else we do in Garve
Why it’s worth doing now in Garve
Sealing behind the M&E trades area by area beats a sweep at the end. Openings are visible, access is open and nothing has to be taken down. In Scotland, wind-driven rain finds a failed joint quickly, and for a smaller place like Garve, a repair visit takes planning, so it’s better to act early.
Cost follows what’s involved: removing old material, preparing the joints, the product, the access and how the work is phased. Call for a fixed quote.
Why choose Mastic Doctor in Garve
- Health and safety: CHAS accredited
- One phone line for London, the South East and Scotland
- Failed material removed, not covered up
- 12-month guarantee on workmanship
See our cost guide and how we’re accredited.
Your questions answered
Do you design the fire stopping for buildings in Garve?
No, that sits with the designer, fire engineer or building control. We install what’s specified, to the product’s tested detail.
How do Scotland’s building standards affect fire-rated sealant in Garve?
Under Scotland’s non-domestic Technical Handbook (clause 2.1.14), service penetrations should keep at least the wall or floor’s fire resistance duration, using products tested for their end use. Design sits with the designer and the verifier; installation to the tested detail is our part.
Will you just go over the old sealant?
No, never. Overlaying old sealant is a frequent cause of early failure, so everything comes out first.
Will your applicators have CSCS cards?
Yes. Should the site need card details in advance, tell us and we will confirm them with the quote.
Will you come and look before quoting?
Photos, drawings or a schedule are often enough to quote. If the job needs a look first, we will arrange a visit before quoting.
What hours do you work?
We’re in the office from 8am until 5pm, Monday to Friday. Tell us your site hours and access windows and the work will be fitted around them.
Can the building stay open while you work?
Yes, with some planning. Tell us your site hours and access windows and we’ll plan around them.
What we can’t put right
A few problems need another trade or a different fix, and we say so rather than covering them up:
- Reviewing a building’s overall fire safety
- Signing off or certifying a building’s fire stopping
- Large openings beyond what any sealant detail covers
Not sure which it is? You can speak to us on 01277 525 020 or email a schedule or drawings and we will tell you honestly.
Where we work in Garve
- Service gaps in risers
- Joints between fire-resisting walls and floors
- Cable penetrations
- Linear gaps at wall heads
- Pipe penetrations
- Small duct penetrations where the tested detail allows
Our process
We schedule the visit to fit the site hours and access windows you give us. While we’re working, the area stays contained and tidy, and your contact hears from us before we move to the next area. Where we can, we combine work around Garve with other jobs nearby. Let us know if your dates have any give.
- We ask for the product and detail your designer has specified.
- Openings are measured and grouped by detail.
- Old or wrong materials are cut out.
- Where the detail needs backing, it goes in at the stated depth.
- Fire-rated or intumescent sealant goes in around the services and is tooled off.
- Completed areas are checked with you, with the records agreed when we quoted.
Before we start on site
- Clear stock, furniture or equipment away from the joints
- Explain the parking and delivery arrangements
- Let building users know which areas are affected
Getting a fixed quote
Every job follows the same four steps: send details, get a quote, we seal, guaranteed. The first step is to give us a call on 01277 525 020 or email a schedule or drawings with what you know.
Read more
Aftercare for building managers
After handover, a little attention goes a long way:
- Check with the data sheet before painting over fire sealant
- Look above ceilings when tiles are lifted for other jobs
- Arrange inspection before areas are covered up
- Make fire stopping part of every scope that crosses a fire-resisting wall
After every round of M&E works, check that the openings created have been sealed. A short check at the end of each job saves a long hunt later.
Ask every contractor who works in risers or voids to report openings they create. It costs little and catches breaches early.
Where services cross fire walls in Garve
Scottish guidance (non-domestic Technical Handbook, clause 2.1.14) asks that penetrations match at least the fire resistance period of the element they pass through, with products tested for that end use. Our part is installing the specified fire-rated sealant to its tested detail.
Around Garve, fire-stopping design belongs to the designer and building control; installation to the specification is our part.
Garve (Gaelic: Gairbh) is about 20 miles north-west of Inverness, in Highland. Commercial clients in Garve use us for work on service penetrations. 256 places across Highland fall within our area, including Garve.
Commercial sites across IV23 are covered. For a building on Station Road, Matheson Road and Stirling Drive or nearby, send details and we’ll quote for service penetrations. Just outside Garve, we also work in Lochluichart (4 miles west), Contin (5 miles south-east), Strathpeffer (6 miles east), Blairninich (7 miles east) and Marybank (7 miles south-east). Bigger towns within reach include Dingwall (10 miles east), Muir of Ord (11 miles south-east), Conon Bridge (10 miles east), Beauly (12 miles south-east), Evanton (13 miles east) and Kirkhill (14 miles south-east). Island and remote sites need extra planning, with travel, ferry crossings where needed and weather to allow for, so give the site location in your enquiry.
Around Garve
Garve has its own railway station: Garve station. Green spaces nearby include Loch Garve and Càrn na Dubh Choille.