Fire stopping in Appledore Heath
Fire-rated and intumescent sealing of service penetrations and linear gaps throughout Appledore Heath and nearby, carried out by CSCS-carded applicators. Fully insured and CHAS accredited.
- Openings found when ceilings come down for a refit
- Head-of-wall gaps with no fire seal
- Seals disturbed by maintenance and left open
Fire stopping in Appledore Heath
Send drawings, photos or a joint schedule, or tell us about the site, and we’ll come back with a fixed quote.
Fire stopping for commercial buildings in Appledore Heath
On a fit-out or refurbishment, we follow the services contractors floor by floor. We work from your penetration schedule or marked-up drawings. Tell us what records you need and we will confirm with the quote. Site teams most often ask us about service penetrations left open after M&E works and snag lists that include open service penetrations, on joints between fire-resisting walls and floors, service gaps in risers and linear gaps at wall heads. Whoever orders the work in Appledore Heath, the brief is usually the same: a clear scope, tidy work and joints that don’t fail again.
A job near Appledore Heath is typically planned around one visit, with the specification and photographs sent in advance. Design and sign-off belong to the designer or building control; we install what’s specified.
Our workmanship is guaranteed for 12 months, in Appledore Heath as everywhere else we work. If a joint we sealed fails because of how it was installed, we come back and put it right.
- Location
- Appledore Heath (TN26)
- Region
- Kent
- Guarantee
- 12 months on every job
- Quotes
- Fixed quote, scope in writing
- Call
- 01277 525 020
- Last updated
- 3 November 2026
Where services cross fire walls in Appledore Heath
Appledore Heath lies roughly 49 miles out from central London. Business park offices in the commuter belt are refitted as tenants change, and each fit-out adds services through compartment walls; the gaps need the specified seal. Fire stopping of openings and penetrations in England falls under Approved Document B. Its BS 476 references are being withdrawn from 2 September 2029, with BS EN 13501-2 classification taking over, subject to transitional arrangements. What we install is set by the specification, and it goes in to the tested detail.
Older community buildings such as Church of St Peter and St Paul that have been rewired or given new heating can have service gaps through walls worth checking against the specification.
Appledore Heath is about 8 miles south-west of Ashford, in Kent. Our applicators travel to Appledore Heath for work on service penetrations. Appledore Heath is one of 931 places we cover in Kent for service penetrations. For work in that direction, see our Brighton page (42 miles or so).
Anyone looking for fire stopping in TN26 gets the same process as the rest of our area: send details, get a quote, we seal, guaranteed. We cover commercial and managed buildings on School Road, Heathside and Woodchurch Road and the roads nearby. Just outside Appledore Heath, we also work in Appledore (1 mile south), Stone in Oxney (2 miles south-west), Reading Street (2 miles west), Brattle (2 miles north) and Brook Street (2 miles north-west). A short drive away, we cover Ashford (8 miles north-east), Hythe (13 miles east), Tenterden (4 miles north-west), Kennington (10 miles north-east), New Romney (8 miles south-east) and Staplehurst (13 miles north-west).
Local landmarks in Appledore Heath
The closest station to Appledore Heath is Appledore (Kent) station, roughly 1.6 miles east of the centre. Well-known places in the area include Woodchurch Village Life Museum (3 miles north). Green spaces nearby include Orlestone Forest.
Nearby places to Appledore Heath
Also in Appledore Heath
Our process
We begin with a short walk round with whoever looks after the building, to confirm the scope, the order of work and any areas we must keep clear. Then we strip out anything that has failed, prepare every joint and seal it. For a building around Appledore Heath, tell us how to find it and who will meet us. Send that with the details and we’ll confirm the plan with the quote.
- We read the specification, drawings or penetration schedule you send and ask about anything unclear.
- On site, each opening is checked against the tested detail it is meant to follow.
- Anything that doesn’t belong in the opening, such as expanding foam or general-purpose filler, is removed.
- Mineral wool or other backing goes in wherever the detail asks.
- We apply the specified sealant to the depth and around the services as the detail shows.
- Openings that need a collar, wrap, batt or other product are flagged to you rather than filled with sealant.
Before we start on site
- Send any specification or drawings in advance
- Tell us your opening times and when work is allowed
- Agree which areas must stay open
Ask for a quote
If there’s a specification, drawings or a tender package, send it with your enquiry, and we’ll price the work to it. Smaller jobs need nothing more than photos and a few notes.
Advice
Aftercare for building managers
After handover, a little attention goes a long way:
- Keep product data and details in the fire safety file
- Include service cupboards in routine inspections
- Have penetrations checked while they can still be seen
- Check with the data sheet before painting over fire sealant
During planned inspections, look at seals in risers, cupboards and voids. Look for cracks, unsealed new cables and gaps that have been enlarged, and report them promptly.
Keep a register of where seals are and what they are made of. When a new service goes through, everyone knows which product and detail to match, which saves guesswork.
Commercial clients in Appledore Heath
As a CHAS accredited contractor and Constructionline member, we’re straightforward to vet for your supplier list. We’re fully insured, and our insurance certificate can go with the quote.
Whether you are a managing agent, a property factor or an owner’s representative: send details, get a fixed quote, we seal, guaranteed. Keys, access and contacts can be agreed in advance.
When to call us in Appledore Heath
Most open service penetrations are left by later work. New cabling, rerouted pipework or a data route drilled through a riser leaves an opening that nobody returns to. Across several fit-outs, the openings add up.
What tends to prompt an enquiry:
- Unsealed joints where partitions meet the slab
- Penetration schedules that need working through
- Expanding foam used as fire stopping
- Fire sealant pulled out of the opening
In a hotel such as The Swan Hotel, which lies south of Appledore Heath, new pipework or cabling through bedroom and corridor walls needs sealing with the specified product.
Comparing quotes
- Whether primer will be used where the manufacturer specifies it
- How they handle RAMS and site documents
- Will failed sealant be removed rather than covered?
- How they’ll work around occupants
Leave it or put it right?
Leave a penetration open and smoke and fire can cross into the next compartment far earlier than intended. Putting it right is typically a modest job when the openings are accessible. Left until ceilings are closed or a tenant moves in, the same work costs more access and more disruption. For buildings around smaller places like Appledore Heath, water damage can go unnoticed for longer, especially where a building isn’t used daily, so a failed joint can leak for a while before anyone sees it. Renewing joints in good time avoids the problem.
Cost follows what’s involved: stripping out, preparation, sealing, access and phasing. Call for a quote and we will explain how it’s made up.
What you get with us
- Commercial sealant work since 2005
- CSCS-carded applicators
- Failed material removed, not covered up
- A Constructionline member, so easy to vet
General trades versus a specialist
What you see is the finished bead, but most of the work is hidden. Backing rod, primer where specified and a joint designed to move with the building are where general trades tend to cut corners.
There’s also the paperwork. Main contractors and clients often ask for CSCS cards, RAMS and insurance details, and we’ll confirm the paperwork you need with the quote.
Appledore Heath: questions and answers
What happens to BS 476 references for fire stopping in Appledore Heath?
Approved Document B loses its BS 476 references from 2 September 2029, and BS EN 13501-2 becomes the route, subject to transitional arrangements. The designer or fire engineer sets the specification, and we install the product to the manufacturer’s tested detail.
Do you decide the fire-stopping details for buildings in Appledore Heath?
No. The designer or fire engineer sets the detail and building control accepts it. Our part is installing the specified product to its tested detail, and telling you if the detail calls for something other than sealant.
Does weather matter for sealant work?
It can, for external work. Sealant won’t bond properly to a wet or frosty joint, so we watch the forecast and rearrange outside work if we have to. Internal work is far less affected.
Are you CHAS accredited?
Yes. We’re CHAS accredited and a Constructionline member.
How many days will you need on site?
That varies with the scale of the job, though a typical visit normally takes a single visit for a short list of penetrations, or a phased programme for a whole building. For bigger or phased jobs, we will set out a timescale with the quote.
Is your workmanship covered by a guarantee?
Yes, for 12 months. If a joint fails because of how we installed it, we come back and put it right.
How do you choose the sealant?
The specification comes first, if there is one. If there isn’t one, it comes down to the joint: how much it moves, what it bonds to and whether it’s wet, trafficked or fire-rated.