Fire Stopping in Altens
Fire-rated and intumescent sealing of service penetrations and linear gaps throughout Altens and nearby, by CSCS-carded applicators. CHAS accredited and fully insured.
- Fire-stopping items raised at inspection or handover
- Non-fire-rated filler around services
- Head-of-wall gaps with no fire seal
Fire stopping for Altens sites
Share the site address and what’s failing, and we’ll reply with a fixed quote or arrange a visit.
Owners, agents and contractors
Hospitality, education, healthcare, office and retail clients book us directly too. We plan around the way the building is used, so guests, pupils, patients or staff are disturbed as little as possible.
For main contractors, we work as the sealant subcontractor, on new build and refurbishment alike. Programme, specification and site rules come first, and our applicators hold CSCS cards.
Fire stopping in Altens, done properly
We should be clear about what we do and don’t do. The designer, fire engineer or building control decides which fire stopping is required. We fit the specified fire-rated sealant following that specification and the maker’s installation guidance in Altens and nearby. We work on cable penetrations, joints between fire-resisting walls and floors and pipe penetrations, and what we are called in for most is fire-stopping items raised at inspection or handover and seals that don’t match their tested detail. A single leaking joint is often how a building in Altens first comes to us: we look at the rest while we are there and tell you what we find.
Tenement blocks and converted stone buildings in Scottish cities often hide old service routes through walls and floors. Wall type and service type decide the product, so both are checked before sealing.
A 12-month guarantee applies to all our work. If an installation problem shows up, call 01277 525 020 or use the quote form and we’ll arrange a return visit.
- Location
- Altens (AB12, AB99, AB10)
- Wider area
- Aberdeen
- Cover
- 12 months on our workmanship
- Quotes
- Fixed quote, scope in writing
- Phone
- 01277 525 020
- Page updated
- 3 November 2026
Questions we are asked in Altens
How do Scotland’s building standards affect fire-rated sealant in Altens?
Under Scotland’s non-domestic Technical Handbook (clause 2.1.14), service penetrations should keep at least the wall or floor’s fire resistance duration, using products tested for their end use. The detail is set by the designer and goes through the warrant process; we install the specified product to its tested detail.
Does your area include sites such as Altens Industrial Estate, near Altens?
Yes, sites like Altens Industrial Estate are within our area, along with the rest of Altens. Send details of the unit and the work through our quote form for a quick quote.
Is colour matching possible?
It depends on the product specified. Some ranges are wide, others limited, so we’ll confirm the colours available for the specified product with the quote.
What about RAMS and site documents?
Let us know which documents the site needs, such as RAMS, an insurance certificate or CSCS details, and we will confirm them with the quote.
Do you need to see the site first?
That depends on the size and complexity of the job. Straightforward work can often be priced from photographs and measurements, while larger or less clear jobs get a site visit first.
Is Altens in your area?
Yes. Altens falls within our area, and you can give us a call on 01277 525 020 or send details through our quote form to get started.
How long before the joints can be used?
Curing time varies by product, and we confirm it on the day.
How the quote is worked out
To price the job, we consider:
- Access and working height
- Specialist products, such as fire-rated or hygienic sealants
- The total length or number of joints
- Joint width, depth and condition
We don’t publish prices, since every building and every scope is different. For a fixed figure, call for a quote and we will price your job on its own details.
What we need to price the job
For an accurate fixed quote, we need to understand the site. Useful things to include:
- The site address and postcode
- A wide shot and a close-up of the area
- Whether an asbestos survey exists
- Rough lengths or quantities, or drawings if you have them
Every quote starts with the facts: what’s there, how much of it, how we reach it and what’s specified. Share whatever details you have and we’ll fill any gaps with a visit.
What the job involves on each surface
Linear joints
Head-of-wall gaps, slab edges and wall junctions are linear joints. BS EN 1366-4 testing sets the joint widths, depths, backing and movement a seal covers.
Drylining partitions
Plasterboard partitions are tested as a specific construction. The sealant detail has to be tested in that wall type, with the stated board layers.
Fire stopping around Altens: how the place shapes the job
Scottish guidance (non-domestic Technical Handbook, clause 2.1.14) asks that penetrations match at least the fire resistance period of the element they pass through, using products tested for the way they’re used. Where fire-rated sealant is specified, that’s what we install, to the tested detail. There are several hotels within about 2 miles of Altens. Bedroom-to-corridor walls in hotels are normally fire-resisting, so new cabling or pipework through them has to be sealed to the tested detail.
At a university such as Robert Gordon University (2.2 miles west of Altens), labs, lecture blocks and residences are re-serviced often, so penetration seals are best checked after M&E work. Industrial units on estates such as Altens Industrial Estate (to the north-east of Altens) often separate offices from warehouse space with fire-resisting walls, and new services through them need the specified seal. At a healthcare site like Albyn Hospital, which lies north-west of Altens, new services through compartment walls are a constant, and each needs the specified seal.
Altens is about 2 miles south-east of Ferryhill, in Aberdeen. Altens sits inside our coverage and the rest of Aberdeen, with the same fixed quotes and 12-month guarantee as everywhere else. We work across 40 places in Aberdeen, from busy centres to rural villages.
Commercial sites across AB12, AB99 and AB10 are covered for service penetrations. Streets here include Minto Road, Redmoss Road and Minto Avenue, and sites on any of them can send details for a fixed quote. Close to Altens, our area also takes in Cove Bay (1 mile south), Tullos (1 mile north), Balnagask (2 miles north), Torry (2 miles north) and Footdee (2 miles north). Bigger towns within reach include Aberdeen (3 miles north-west), Rosemount (3 miles north-west), Berryden (3 miles north), Dyce (7 miles north-west), Tillydrone (4 miles north) and Queen's Cross (3 miles north-west).
Landmarks near Altens
Recent enquiries here include premises near Harlaw Academy and Duthie Park and the streets around them. For rail, the closest station is Aberdeen station, about 2.1 miles north. Other landmarks nearby include Aberdeen Trades Hospitals (2.4 miles north) and Union Square Aberdeen (2.1 miles north). The countryside around Altens includes Portlethen Moss and Loirston Loch.
Looking after the joints
Your facilities or cleaning team can help the joints last. Share these points with them:
- Settle who seals which penetrations at the start of a project
- Get seals inspected before ceilings and boxing close
- Check with the data sheet before painting over fire sealant
- Don’t let anyone top up a fire seal with the wrong product
Never top up a fire seal with foam, ordinary silicone or filler. A repair should use the original product, installed the same way.
On fit-outs, get the fire-stopping specification agreed before the services go in. Details can then be picked to suit the actual pipes, cables and ducts.
Our process
When we get to site, we report to your site contact and complete whatever induction the building runs. Floors, finishes and fittings next to the joints are covered before any cutting starts, and the work usually takes a single visit for a short list of penetrations, or a phased programme for a whole building. For premises in Altens, tell us about access times, shared entrances and any building rules, so the work can be phased and areas kept in use.
- First we confirm the product and tested details named in the specification.
- Openings are measured and grouped by detail.
- Improvised fillers and failed sealant are removed.
- Mineral wool or other backing is fitted where required.
- We gun the sealant in to the specified depth around each service and tool it.
- We walk the completed areas with you and confirm the records agreed at quote stage.
Getting the site ready
- Let us know about inductions and permits
- Agree which areas must stay open
- Share your working hours and any access restrictions
Get a fixed quote
The quickest route to a quote is a few photographs and the site postcode. Upload them with the quote form, or phone 01277 525 020 or use the quote form to discuss it first.
Advice
What else we do in Altens
What happens if it’s left?
It is cheaper to seal service penetrations as each services package finishes than to come back for them later. While the area is still open, every opening is easy to see and reach. Failed sealant in a shared building in Altens can affect more than one owner. Acting early avoids disputes and bigger repairs.
No two sites price the same: the joint sizes, the specified product, access and working hours each have a bearing. A fixed quote follows once we understand the job.
Why us?
- Fully insured
- 12-month guarantee on workmanship
- A Constructionline member, so easy to vet
- Fixed quotes based on photographs, drawings or a visit
Take a look at what affects the cost and our accreditations and insurance.