Expansion and movement joint sealing in Scalloway, Shetland Islands
Commercial sealant work in Scalloway for contractors, FMs and building owners: expansion and movement joint sealing in walls, decks and floors, quoted at a fixed price.
- Joints where the bead has lost adhesion
- Weathered movement joint sealant that no longer flexes
- Previous reseals laid over old sealant
Need expansion joint sealing in Scalloway?
Send drawings, photos or a joint schedule, or tell us about the site, and we’ll come back with a fixed quote.
How we handle expansion joint sealing in Scalloway
We cover the full range of movement joints: vertical joints in brick and block facades, joints between precast or cladding panels, concrete slab and deck joints, ramps, podiums and internal floors. Every one calls for a sealant picked for its movement, exposure and traffic and we name it in the quote. We work on cladding panel joints, blockwork control joints and podiums and floor movement joints, and the usual reasons a site gets in touch are joints where the bead has lost adhesion and leaks through car park deck joints onto the level below. Sealant applicators who only do sealant are a different proposition from a general trade with a gun in the van: on jobs in Scalloway, preparation and product choice get the time they need.
Travel to smaller places like Scalloway is planned so the work is done in one trip where possible. Send photos, joint widths and details of the traffic first.
Our workmanship is guaranteed for 12 months, in Scalloway as everywhere else we work. If our installation lets you down in that time, we return and fix it.
- Location
- Scalloway (ZE1)
- Region
- Shetland Islands
- Guarantee
- 12 months on our workmanship
- Quotes
- Quoted before any work starts
- Telephone
- 01277 525 020
- Last updated
- 3 November 2026
Cost factors for movement joints
Sealant work doesn’t have a standard rate, since sites vary so much. What we look at:
- The total length or number of joints
- Which sealant the job calls for
- How much existing material needs removing
- Induction, permit and paperwork requirements
Quantities, awkward access and phased working all shape the price. So do site requirements such as inductions and permits.
What we need to price the job
Good information means a firmer quote. Helpful details to send:
- Any specification or named product
- The site address and postcode
- How the joints are reached, and at what height
- Rough lengths or quantities, or drawings if you have them
Every job follows the same four steps: send details, get a quote, we seal, guaranteed. The first step is to ring 01277 525 020 or send photos by email with what you know.
Nearby places to Scalloway
What else we do in Scalloway
What we can’t put right
Part of a good diagnosis is knowing where sealant stops. You will hear from us if the cause turns out to be one of these:
- Movement on a scale no sealant is meant to absorb
- Waterproofing layers buried beneath the sealant
- Broken or spalled joint edges, which need repairing before any sealant goes in
If in doubt, phone 01277 525 020 or use the quote form and we will say what we think.
What we seal
- Podiums and floor movement joints
- Blockwork control joints
- Brickwork movement joints
- Car park decks and ramps
- Cladding panel joints
- Precast concrete panel joints
Slabs, ramps and loading bays in Scalloway
Scalloway sits close to the coast, within about 1 mile. External movement joints in car parks, ramps and yards near the coast take salt and wind-driven rain on top of traffic, and edges left open tend to break up faster. Work on Scalloway has to fit the ferry timetable and the forecast. Photos and joint sizes help us load the right products.
Sites like Gilbert Bain Hospital, 4.3 miles to the east of Scalloway, carry ambulances, deliveries and visitors’ cars over their road and deck joints.
Scalloway is in the Shetland Islands. Our applicators travel to Scalloway for work on movement joints, handled exactly as we handle every other area. Scalloway is one of 63 places in the Shetland Islands on our list.
We take on movement joints across the ZE1 postcode area, for business premises of every kind. Among the streets we cover are Main Street, Craigpark Road and Meadowfield Road. You’ll find Scalloway on or near the B9074, so getting applicators and materials to site is simple. Just outside Scalloway, we also work in Gulberwick (2 miles east), Hamnavoe (3 miles south-west), Veensgarth (3 miles north-east), Sound (4 miles east) and Toogs (4 miles south-west). Scalloway is one of the busier places in the Shetland Islands, and its commercial and public buildings are all within our area. Island and remote sites need extra planning, with travel, ferry crossings where needed and weather to allow for, so mention the location when you phone 01277 525 020 or send details through our quote form.
Near you in Scalloway
Locally, jobs take us to sites close to Fisherman's Arms and the streets around them. A little further out are Castle Holm (4.9 miles north) and Gilbert Bain Hospital (4.3 miles east). For a walk, there’s Hill of Berry and Loch of Burwick.
Common problems we fix in Scalloway
Sometimes the sealant holds but the substrate breaks away. Weak or crumbling concrete, brick or render edges give the sealant nothing sound to grip.
It’s worth sending us details if you spot any of the following:
- Weathered movement joint sealant that no longer flexes
- Arrises breaking up along floor joints
- Movement joints with split or torn sealant
- Joints where the bead has lost adhesion
Around Scalloway, each joint gets a filler or sealant matched to what crosses it and how much it moves.
Questions to ask before you book
- Is the sealant right for the movement and the substrate?
- What the guarantee covers, and for how long
- What site paperwork they can supply
- Will CSCS-carded applicators be on site?
How a job runs
At the end of each section, we remove the tape, clean down and inspect every joint. Where the sealant needs time to cure before use, we tell you and sign the area. Jobs near Scalloway are often grouped with others in the same area. Let us know if your dates have any give.
- First the joints are inspected, widths measured and the type of failure noted.
- A fixed quote names the sealant we propose and its movement class.
- Where areas have to stay open, we agree a phased sequence before starting.
- We strip the old sealant or filler and prepare each face until it’s sound and dry.
- Backing rod or bond-breaker sets the depth, primer goes on where specified, and the sealant is applied and tooled.
- We check each joint with you, confirm the cure time and sign off under our 12-month guarantee.
What we need from you
- Send asbestos survey details if the building is pre-2000
- Arrange parking or a loading space
- Tell us which areas need to stay in use
Quotes
The quickest route to a quote is a few photographs and the site postcode. Upload them with the quote form, or ring 01277 525 020 or email the details over to discuss it first.
Read more
For managing agents and facilities managers
For main contractors, we work as the sealant subcontractor, on new build and refurbishment alike. Programme, specification and site rules come first, and our applicators hold CSCS cards.
If you look after buildings for someone else, you need clear quotes and clear reporting. We quote a fixed sum, confirm the scope and walk the finished work with you or your representative.
FAQs: Scalloway
Our building in Scalloway is near the coast: does that change the sealant?
It can. Coastal exposure works external joints harder than inland weather. That puts more weight on product choice, primers where the manufacturer specifies them, and correct joint sizing.
Is hospital work, at somewhere like Gilbert Bain Hospital, something you do?
Yes, healthcare and care buildings are part of our work. We follow the site’s permits, sign-in and infection-control procedures in every area.
Will your applicators have CSCS cards?
Yes. If you need card details for site access, let us know and we will send them with the quote.
What about RAMS and site documents?
Let us know which documents the site needs, such as RAMS, an insurance certificate or CSCS details, and we will confirm them with the quote.
How do I request a quote?
It works in four steps: send details, receive a fixed quote, we carry out the work, and it’s guaranteed. Step one needs little more than photographs and a postcode.
What causes movement joint sealant to fail?
The common causes are poor preparation, three-sided adhesion, the wrong movement class and weathering. We diagnose which one it is before resealing since each needs a different fix.
Do you use silicone or polyurethane in movement joints?
The right product depends on the joint. Low-modulus neutral-cure silicone suits many facade joints, while polyurethane is common in trafficked floor and deck joints unless the specification names something else.
Surface by surface
Podium joints
Podium joints often sit within a waterproofing system. We reseal the joint where sealant is the specified fix.
Car park decks and ramps
Car park joints are some of the hardest-working joints in any building. We use a sealant made for wheel loads and the expected movement with bays done in phases so the car park keeps running.