Industrial and floor joint sealing in Lewiston, Highland
Floor joint sealing and filling in warehouses, factories and industrial units throughout Lewiston and nearby, by CSCS-carded applicators. CHAS accredited and fully insured.
- Soft sealant dragged out of trafficked joints
- Drivers complaining about joints on a route
- Old filler gone hard, cracked or loose
Need floor joint sealing in Lewiston?
Share the site address and what’s failing, and we’ll reply with a fixed quote or arrange a visit.
Floor joint sealing in Lewiston
Sometimes the concrete either side of a joint has already spalled. A filler laid against broken edges has nothing sound to grip, so we will tell you if the joint edges need repairing first and explain how it affects the programme. If you have trucks and loads jolting over damaged joints and brittle joint filler breaking up, we can help. A specialist sealant contractor works differently from a general builder: in Lewiston, that means joint design, primers and backing rod as standard.
For outside joints near Lewiston, the Scottish weather sets the timetable: sealant needs a dry joint and a temperature within its range, so dates have some give. Internal floors can be done whenever suits the site.
We stand behind the joints we seal: 12 months, guaranteed. That covers our preparation and application, and if something we did falls short, we return to it.
- Where
- Lewiston (IV63)
- Wider area
- Highland
- Cover
- A 12-month guarantee
- Quotes
- A fixed quote before we start
- Call
- 01277 525 020
- Page updated
- 3 November 2026
Looking after the joints
Keep the joints in good shape with a few simple steps:
- Hold traffic back until the product has cured
- Clear packed debris from open joints regularly
- Record damaged joints with a photo and a location
- Start with the dock areas, where joints fail soonest
Walk the main truck routes every few months and look along the joint lines. Watch for filler pulling away from an edge, fresh chipping or grit collecting and keep photos so changes are easy to compare.
A broken joint on a main route is crossed by every truck on that route. Early treatment protects wheels, loads and drivers as much as the floor.
Leave it or put it right?
Some runs only need partial renewal or topping up. Where existing filler is well bonded and the gap beside it is small, a full strip-out isn’t always needed, and we’ll say which joints need what. Exposed buildings in Scotland take a lot of weather, so it’s worth renewing joints around Lewiston before they leak.
The specified product makes a difference, as does the preparation each joint needs, such as cutting out, priming or new backing rod. Access, phasing and site requirements come into it too.
Why us?
- CHAS accredited contractor
- One phone line for London, the South East and Scotland
- CSCS-carded applicators
- Old sealant cut out, never sealed over
Take a look at our cost guide and our accreditations.
Your questions answered
What paperwork can you provide for a job in Lewiston?
We will confirm the paperwork you need, such as RAMS, our insurance certificate and CSCS details, with the quote. We hold £5m public liability insurance, are CHAS accredited and a Constructionline member, and our applicators are CSCS-carded.
Is Lewiston too small for you to travel to?
No. Small places get the same service as large ones. We cover the whole of Scotland. Good photographs up front let us bring everything on the first visit.
How do we get a quote for floor joints?
Approximate metres of joint, photographs of typical and worst areas, and a floor plan are normally enough for a quick quote. We can visit where that helps, and you can give us a call on 01277 525 020 or email drawings and photos to arrange it.
Do you offer coloured sealant?
Often, yes. Sealants are made in a wide range of standard colours, and matching to RAL references or nearby finishes is commonly requested. We will confirm the colours available for the specified product.
Do you seal on top of existing sealant?
No. Failed sealant is removed and the faces cleaned back to sound, dry material first, since fresh sealant will not bond reliably to aged material.
Will we need to close the floor?
We phase it. We work aisle by aisle or zone by zone so the rest of the floor stays in use. Tell us your site hours and access windows and we’ll plan around them.
Are your applicators CSCS-carded?
Yes. We use CSCS-carded applicators, as many construction sites ask for.
Our process
The first thing on site is a walk round with your contact, agreeing which joints are in scope, where to start and what must stay open. Then we strip out anything that has failed, prepare every joint and seal it. For work around Lewiston, we aim for one trip, which is why we ask for photographs and a full list first. Outside work also needs a suitable weather window.
- First comes a walk of the floor to record joint sizes, broken edges and traffic routes.
- You get a fixed quote with the product and the phasing set out.
- We remove failed material and packed debris until sound concrete is exposed on both faces.
- We vacuum each run and prime it if the chosen product requires a primer.
- The chosen product is placed to its specified depth and trimmed level with the floor.
- Each phase reopens when the product is ready for wheels, then we start the next.
What we need from you
- Move anything stored against the joints
- Send asbestos survey details if the building is pre-2000
- Point out any areas we must not close
Ask for a quote
Every quote starts with the facts: what’s there, how much of it, how we reach it and what’s specified. Share whatever details you have and we will fill any gaps with a visit.
Read more
Owners, agents and contractors
Building owners and managing agents use us on everything from one building to a spread of sites around Lewiston. Several sites can go on one quote, which keeps the paperwork simple.
We take on planned maintenance as well as one-off repairs: working through a building or an estate in stages that fit your budget. Lewiston can form part of a wider programme.
Also near Lewiston
More services for Lewiston
Joints that move: notes for Lewiston
Lewiston is in the west of Scotland, the wetter side of the country. Open joints in car parks and yards let in more water than in drier areas. We wait for dry, workable days to seal them.
For floors and slabs around Lewiston, the product is chosen for the traffic and the movement at each joint. In a school such as Glen Urquhart High School, movement joints in brick, block and hall floors tend to be forgotten until they leak.
Lewiston is about 13 miles south-west of Inverness, in Highland. Looking for floor joint sealing in Lewiston? We can help, as we do across Highland. 256 places across Highland fall within our area, Lewiston among them.
Anyone looking for floor joint sealing in IV63 gets the same process as the rest of our area: send details, get a quote, we seal, guaranteed. Among the streets we cover are Dal of Borlum, Carn Glas and Carriers Croft, and sites on any of them can send details for a fixed quote. Nearby places we also cover include Drumnadrochit (1 mile north), Torness (4 miles east), Gorthleck (6 miles south), Dores (7 miles north-east) and Kiltarlity (8 miles north). Further afield, our area takes in Inverness (13 miles north-east), Merkinch (14 miles north-east), Hilton (13 miles north-east), Crown (14 miles north-east), Millburn (14 miles north-east) and Muir of Ord (13 miles north). Island and remote sites need extra planning, with travel, ferry crossings where needed and weather to allow for, so mention the location when you phone 01277 525 020 or email drawings and photos.
Landmarks near Lewiston
Around Lewiston, our work takes us to commercial buildings near Drumnadrochit Hotel and the streets around them. A little further out are Urquhart Castle (1.3 miles east) and Urquhart Castle Visitor Centre (1.2 miles east). Green spaces nearby include Loch Ness.
What affects the price in Lewiston
These are the things that shape the price:
- Location, for remote and island sites
- How much there is to seal
- How accessible the joints are
- Site requirements such as inductions and permits
The work involved drives the cost: removing old material, preparing the joints, the product, the access and how the work is phased. Call for a quote.
What to include in your enquiry
For an accurate fixed quote, we need a clear picture of the site. Send us:
- The asbestos register, for older buildings
- Specification clauses that apply
- Access details, including height
- Where the site is, with the postcode
A handful of photos and a postcode is the fastest way to a quote. Send them through the quote form, or call 01277 525 020 or email us if you’d rather talk the job through.
What we can’t put right
Some faults sit outside our scope, and we point that out rather than sealing over them:
- Level or flatness problems across the floor
- Unstable slabs moving under traffic
- Cracks across panels caused by settlement or overload
If in doubt, phone 01277 525 020 or send photos by email and we’ll say what we think before you book.
What we seal
- Loading bays
- Saw-cut induced joints
- Joints along racking aisles
- Construction joints
- Forklift and pallet-truck routes
- Retail and showroom floors