Fire stopping in Smithstone
Fire-rated and intumescent sealing of service penetrations and linear gaps throughout Smithstone and nearby, by CSCS-carded applicators. CHAS accredited and fully insured.
- Old intumescent sealant that has split away
- Seals that don’t match their tested detail
- Expanding foam used as fire stopping
Need fire stopping in Smithstone?
Photos, a specification or a quick description of the joints is enough to start a fixed quote.
Fire stopping in Smithstone
It helps to set out our role at the start. The designer, fire engineer or building control decides which fire stopping is required. We fit the specified fire-rated sealant following that specification and the maker’s installation guidance on buildings around Smithstone. If you’re dealing with seals disturbed by maintenance and left open and snag lists that include open service penetrations, we can help. A single leaking joint is often how a building in Smithstone first comes to us: we check the joints around it and give you an honest view of what needs doing now and what can wait.
For a building near Smithstone, we plan fire-rated sealing so it’s finished in one visit where possible. Send the specification and photos of the openings, with sizes if you have them.
We stand behind the joints we seal: 12 months, guaranteed. That covers our preparation and application, and we come back if anything isn’t right.
- Place
- Smithstone (G68, G65)
- Region
- North Lanarkshire
- Cover
- 12 months on every job
- Quote
- Quoted before any work starts
- Call
- 01277 525 020
- Last updated
- 3 November 2026
After the work
A few simple habits keep the new joints working:
- Flag new cables with no seal around them
- Check risers and ceiling voids after each round of works
- Foam or ordinary sealant is never a fire-seal repair
- File the specified details where the next contractor can find them
During planned inspections, look at seals in risers, cupboards and voids. Watch for cracked sealant, new services with no seal and openings that have grown.
On fit-outs, get the fire-stopping specification agreed before the services go in. The designer can then choose details that suit the services planned, and installation follows the programme.
How a job runs
We begin with a short walk round with whoever looks after the building, agreeing which joints are in scope, where to start and what must stay open. Then we strip out anything that has failed, prepare every joint and seal it. Travel to smaller Scottish places like Smithstone is planned so the job is finished in one visit where possible, so photos, sizes and a full list matter. External joints need a dry spell as well.
- We start with your penetration schedule, drawings or specification.
- We plan the sequence of floors, risers and voids with you.
- Each opening is checked for wall or floor type, service, gap and depth.
- Unsuitable material is removed and the opening cleaned first.
- Backing and fire-rated sealant are installed to the detail and tooled.
- We tell you about openings that need a different product.
Before we start on site
- Send asbestos survey details if the building is pre-2000
- Send your site hours and access windows
- Point out parking and an unloading spot
Quotes
Every quote starts with the facts: what’s there, how much of it, how we reach it and what’s specified. Share whatever details you have and we’ll fill any gaps with a visit.
Read more
How the job changes by surface
Risers and ceiling voids
Service risers and the voids above ceilings are where openings collect. Access is often tight, so we agree it with you in advance.
Drylining partitions
Holes in board are often cut larger than needed. An oversized hole may be outside the sealant’s range, and the detail may call for board patching or another product.
What sets the cost
What shapes the price:
- Any access equipment needed
- The total length or number of joints
- Working within restricted access windows
- Joint width, depth and condition
Larger quantities, tricky access or phasing all shape the price. So do site requirements such as inductions and permits.
Sending details for a quote
The more we know, the firmer the quote. When you get in touch, include:
- Your programme or deadline
- Whether the building will be occupied during the work
- Access details, including height
- Photos of the joints, close up and from further back
Need a figure for a tender or a budget? We’ll quote against your scope and drawings that you can work with. If you have questions first, phone 01277 525 020 or email a schedule or drawings.
When it isn’t the sealant
Being straight saves everyone time. New sealant won’t cure:
- Fire risk assessments, a job for a competent assessor
- Approving the work on behalf of building control
- Deciding what a wall or floor needs, which belongs to the designer
If in doubt, speak to us on 01277 525 020 or email a schedule or drawings and we’ll say what we think.
Joints and surfaces we work on
- Linear gaps at wall heads
- Cable penetrations
- Joints between fire-resisting walls and floors
- Pipe penetrations
- Service gaps in risers
- Small duct penetrations where the tested detail allows
Site staff or a sealant specialist?
General builders and handymen seal joints, but it isn’t their main trade. A specialist brings correct preparation, depth control with backing rod and a product suited to that particular joint.
Site maintenance staff can often handle a short internal joint. Where it goes wrong is preparation: sealing over old material, sealing onto damp or dusty surfaces, or a product that can’t take the movement.
Smithstone: questions and answers
Is Smithstone too small for you to travel to?
No. Small places get the same service as large ones. Our area covers all of Scotland, cities, towns and islands alike. We plan jobs in smaller places so return trips are kept to a minimum.
Can you take on a job at a hospital such as Victoria Memorial Cottage Hospital?
Yes. Healthcare sites are among the places we work. Work is phased so departments keep running, under the site’s own rules.
What’s the quickest route to a quote?
You can use the quote form on this site; alternatively, ring 01277 525 020 or email drawings and photos. Include photographs or drawings if you have them.
Does the weather affect the work?
For external joints, yes. The joint has to be dry and within the product’s temperature range, so damp, frosty or very cold days can stop external work. Inside work is seldom held up.
Is BS 476 being phased out?
For buildings in England, Approved Document B removes BS 476 references from 2 September 2029. Products are then judged on BS EN 13501-2 classifications. In Scotland, the Technical Handbook sets its own guidance.
Do you take on multi-site work?
Yes. A group of buildings can go on one quote, with one point of contact.
What happens if old sealant might contain asbestos?
Asbestos is possible in some older mastics, particularly in buildings from before 2000. Before we disturb old sealant in an older building, we ask to see the asbestos register or survey, and if asbestos is suspected, work stops until it’s tested. We don’t remove asbestos-containing materials.
Also near Smithstone
What else we do in Smithstone
Fire stopping in Smithstone: the local picture
Under the Scottish non-domestic Technical Handbook, clause 2.1.14, penetrations should be fire stopped to at least the wall or floor’s fire resistance duration, and products should be tested for their end use. Where fire-rated sealant is specified, that’s what we install, to the tested detail.
Refits at places like Cumbernauld Retail Park (less than half a mile south of Smithstone) often reroute services through walls between units. For a site team at a college like New College Lanarkshire - Cumbernauld Campus, which lies east of Smithstone, fire-rated sealing is best scheduled after the summer works. For an estates team at a campus like University of the West of Scotland, 1.8 miles west of Smithstone, summer M&E works are typically followed by a round of penetration sealing.
Smithstone is about 1 mile west of Cumbernauld, in North Lanarkshire. We cover Smithstone, and jobs here get the same fixed quote and 12-month guarantee as anywhere else. Across North Lanarkshire, 100 places are covered, Smithstone among them. Sites around Glasgow have their own page, about 11 miles away.
We take on service penetrations across the G68 and G65 postcode area, for business premises of every kind. Streets here include Taggart Road, Blackwood Road and Old Tower Road. We also cover Balloch (1 mile east), Croy (1 mile north), Craigmarloch (1 mile north-east), Auchinstarry (1 mile north-west) and Westfield (1 mile south) for service penetrations. A short drive away, we cover Motherwell (11 miles south), Coatbridge (7 miles south), Airdrie (6 miles south), Wishaw (13 miles south), Bellshill (9 miles south) and Viewpark (8 miles south).
Landmarks near Smithstone
There’s a railway station in Smithstone itself: Croy station. Other landmarks nearby include Antonine Centre (1.8 miles east) and Cumbernauld Castle (2.7 miles east). The countryside around Smithstone includes Bar Hill and Antermony Loch.