Fire stopping in Reculver
Our CSCS-carded applicators take on fire-rated and intumescent sealing of service penetrations and linear gaps in Reculver and the surrounding area. Send photographs or drawings for a fixed quote.
- Seals disturbed by maintenance and left open
- Fire-stopping items raised at inspection or handover
- Non-fire-rated filler around services
Fire stopping near Reculver
Tell us what needs sealing and where, with photos or drawings if you have them, and we’ll price it.
Common problems we fix in Reculver
Fire stopping can get squeezed at the end of a programme, or done by whoever is on site. That is how unsuitable products and improvised details end up in compartment walls and later need putting right.
These are often picked up first by site or facilities staff:
- Builders’ foam or ordinary silicone in compartment walls
- Improvised or mixed-product fire seals
- Hidden openings found during inspections
- Fire sealant pulled out of the opening
Where a unit on an estate such as Hedgend Industrial Estate (2.8 miles south-east of Reculver), has fire-resisting walls between offices and warehouse, any new service through them should be sealed to the tested detail.
Questions to ask before you book
- How the joint faces will be prepared and primed
- What level of public liability insurance do they hold?
- Whether old or failed sealant will be cut out, not overlaid
- Their approach to joint depth and backing
Fire stopping in Reculver, done properly
Facilities managers in Reculver often find open service penetrations when ceilings come down for other work. Where the walls and floors already have a fire-stopping specification, we can work to it. Where there isn’t one, the designer or fire engineer needs to set one first. We work on small duct penetrations where the tested detail allows, linear gaps at wall heads and pipe penetrations, and what we are called in for most is seals disturbed by maintenance and left open and expanding foam used as fire stopping. Looking for mastic applicators who cover Reculver? We have been sealing commercial buildings since 2005.
Rural conversions around Reculver can put new fire-resisting partitions inside older structures. A penetration seal only performs as tested if product, substrate, service, gap and depth all match the detail.
We sign every job off with a 12-month guarantee. It’s a plain promise: if the work we did fails within twelve months, we return to fix it.
- Where
- Reculver (CT6)
- Region
- Kent
- Cover
- A 12-month guarantee
- Quotes
- Fixed quote, scope in writing
- Call
- 01277 525 020
- Updated
- 3 November 2026
Compartment walls and floors in Reculver
For England, the fire stopping of penetrations is dealt with in Approved Document B. The national BS 476 classes are due to drop out of it from 2 September 2029, leaving the European BS EN 13501-2 route, subject to transitional arrangements. We install whatever has been specified, to the product’s tested detail. Reculver lies roughly 56 miles out from central London. Tenant changes on commuter-belt business parks mean regular fit-outs, and new services through compartment walls; the gaps need the specified seal.
On a hospital site such as Queen Victoria Memorial Hospital (2.4 miles west of Reculver), fire-rated sealant goes in where the specification calls for it, with the work planned around the estates team’s permits. In a school such as Reculver Church of England Primary School, fire-rated sealant goes in around service penetrations where it is specified.
Reculver is about 3 miles east of Herne Bay, in Kent. Anywhere in CT6, it works the same way: details in, fixed quote out, then sealing and a 12-month guarantee. Reculver is one of 931 places we cover in Kent. There’s a separate page for London, about 56 miles away.
We cover the CT6 postcode districts for service penetrations. If your site is on Reculver Lane and Cherry Blossom Drive or close by, send details and we’ll quote for service penetrations. Sites close to Reculver are covered too, including Bishopstone (1 mile west), Hillborough (1 mile south-west), Hawthorn (2 miles south-west), Beltinge (2 miles west) and Highstead (2 miles south-west). A short drive away, we cover Canterbury (8 miles south-west), Margate (8 miles east), Ramsgate (10 miles east), Broadstairs (10 miles east), Whitstable (7 miles west) and Deal (14 miles south-east).
What’s near Reculver
Locally, jobs take us to sites close to Bishopstone Cliffs and The King Ethelbert Inn and the streets around them. For rail, the closest station is Herne Bay station, about 3.5 miles west of the centre.
What happens if it’s left?
Open service penetrations matter on ordinary days, not just in a fire: smoke, noise and draughts pass through them every day. Sealing them to the specified detail deals with the fire risk first and the building feels the difference. Halls, stores and units around places like Reculver may not be checked every day, which gives a failed joint time to do damage. Resealing early avoids that.
Cost follows what’s involved: removing old material, preparing the joints, the product, the access and how the work is phased. Call for a quote and we’ll explain how it’s made up.
What you get with us
- Over 20 years of commercial sealing
- Old sealant cut out, never sealed over
- Fixed quotes based on photos, drawings or a visit
- 12 months’ guarantee on every job
What we can’t put right
We seal joints; we don’t mend everything behind them. On its own, sealant can’t deal with:
- Construction that lacks the fire resistance the seal relies on
- Openings that need collars, wraps, batts or boards rather than sealant
- Writing the fire-stopping specification
Not sure which it is? You can call the office on 01277 525 020 or send details through our quote form and we’ll tell you honestly before you book.
Surfaces we seal
- Service gaps in risers
- Cable penetrations
- Joints between fire-resisting walls and floors
- Small duct penetrations where the tested detail allows
- Linear gaps at wall heads
- Pipe penetrations
After the work
Cleaning and maintenance staff play a part too. Share these points with them:
- Brief every trade that openings they make must be sealed
- Ask the designer to confirm details early on refits
- Have penetrations checked while they can still be seen
- Keep general-purpose fillers away from compartment walls
After the work, brief anyone else working in the area that the openings are now sealed. Any seal cut back for a new service needs reinstating to its tested detail using the same product.
Specify fire stopping early on refits, not as an afterthought. Details can then be picked to suit the actual pipes, cables and ducts, and the work runs in step with the M&E.
Different surfaces, different methods
Plastic pipes
Plastic pipes soften and collapse in a fire. Some intumescent sealants are tested on smaller plastic pipes, but many need a collar or wrap. We confirm material and size first and tell you if sealant isn’t the right product.
Linear joints
Joints at the top of partitions may need to move as the slab above deflects. The specified product and backing for that movement are what goes in, with no gaps along the run.
Places near Reculver
What else we do in Reculver
Our process
We bring the products specified for the job, along with primers and backing rod. Joint faces are cleaned back to sound, dry surfaces, the manufacturer’s primer is applied where it’s called for, and each bead is tooled to a neat concave finish. If others near Reculver need work, visits can be combined, which keeps travel down. A fixed quote is given before anything starts.
- The specification and schedule come first, so we know which details apply.
- We plan the sequence of floors, risers and voids with you.
- Each opening is checked for wall or floor type, service, gap and depth.
- Unsuitable material is removed and the opening cleaned first.
- The specified backing and sealant go in to depth and are finished neatly.
- Anything outside the detail is reported to you rather than sealed.
Preparing the site
- Tell us your opening times and when work is allowed
- Move anything stored against the joints
- Tell staff and tenants when we’ll be in
Quotes
To get a fixed quote, call 01277 525 020 or send details through our quote form with the site address and an outline of the work. Our quote form is another easy route.
Related advice
Questions we are asked in Reculver
What happens to BS 476 references for fire stopping in Reculver?
Approved Document B loses its BS 476 references from 2 September 2029, and BS EN 13501-2 becomes the route, subject to transitional arrangements. Our part doesn’t change: the specified product, to its tested detail.
Is Reculver too far out for you?
Not at all. Reculver is within our area. Our area covers London and the South East counties. Good photos up front let us bring everything on the first visit.
When can you be on site?
The office is staffed Monday to Friday, from 8am until 5pm. Tell us your site hours and access windows and the work will be fitted around them.
Can staff carry on working while you’re here?
In the majority of cases, yes. We phase the work so most of the building stays in use, with each area protected and signed.
What’s the quickest route to a quote?
The quote form is the simplest route, though you can also speak to us on 01277 525 020 or email a schedule or drawings. Include photos or drawings if you have them.
Do you take on small jobs?
Small jobs are welcome alongside larger packages. Photos and a description are enough to start.
Is colour matching possible?
In many cases, yes. Sealants are made in a wide range of standard colours, and matching to RAL references or nearby finishes is commonly requested. We confirm what’s available for the specified product when we quote.