Rankinston fire stopping
Fire-rated and intumescent sealing of service penetrations and linear gaps across Rankinston, carried out by CSCS-carded applicators. CHAS accredited and fully insured.
- Penetration schedules that need working through
- Builders’ foam or ordinary silicone in compartment walls
- Fire-rated sealant that has cracked or shrunk back
Fire stopping in Rankinston
Send drawings, photos or a joint schedule, or tell us about the site, and we’ll come back with a fixed quote.
Owners, agents and contractors
Whether you’re a managing agent, a property factor or an owner’s representative: send the details, accept a fixed quote, and we carry out and guarantee the work. We can agree access arrangements and keyholder contacts beforehand.
Planned maintenance programmes are welcome: resealing failed joints building by building, on a schedule that suits your budget. Rankinston can form part of a wider programme.
About our fire stopping in Rankinston
Most of our fire stopping work happens after the building is up. Each new cable, pipe or data route cut through a fire-resisting wall leaves an opening behind, often unnoticed. Those on your schedule are closed with the specified product. If you are dealing with fire-stopping items raised at inspection or handover and unsealed openings around new pipes and cables, we can help. Looking for mastic applicators who cover Rankinston? We have been sealing commercial buildings since 2005, with CSCS-carded applicators.
Hotels and care homes around smaller places like Rankinston often have services added during refurbishment. We fit the specified fire-rated sealant as its published detail shows and raise it if another product is needed.
Whoever the client is, the cover is the same: twelve months on the work we carried out. It doesn’t extend to damage, faults in the building or work by others, and we’re upfront about that.
- Location
- Rankinston (KA6)
- Region
- East Ayrshire
- Guarantee
- 12 months on every job
- Quote
- Fixed quote, scope in writing
- Telephone
- 01277 525 020
- Updated
- 3 November 2026
Penetration seals near Rankinston
Scotland has its own building standards: the non-domestic Technical Handbook (clause 2.1.14) says service penetrations should be fire stopped to at least the fire resistance duration of the wall or floor, using products tested for the way they’re used. Where fire-rated sealant is specified, that’s what we install, to the tested detail.
For any site around Rankinston, we work to the specification and the manufacturer’s installation guidance, leaving design and sign-off with the designer. For buildings in and around Rankinston, fire-rated sealant is installed where it is specified, to the manufacturer’s tested detail.
Rankinston is about 8 miles south-east of Ayr, in East Ayrshire. We cover commercial sites throughout Rankinston, for single jobs and planned programmes alike. Rankinston is one of 56 places we cover in East Ayrshire. Our Glasgow page has more on work in that area (32 miles or so).
Business premises anywhere in KA6 are within our area. Among the streets we cover are Littlemill Place and Coyle Crescent. Nearby places we also cover include Hayhill (1 mile north-east), Sinclairston (2 miles north-east), Drongan (2 miles north), Millmannoch (3 miles north-west) and Coalhall (3 miles north). Bigger towns within reach include Kilmarnock (15 miles north), Cumnock (8 miles north-east), Annanhill (15 miles north), Galston (14 miles north), Mauchline (8 miles north) and New Farm Loch (15 miles north).
What’s near Rankinston
Nearby you’ll also find Kerse Castle (0.8 miles west) and Dunaskin Open-air Industrial Museum (3.7 miles south). The countryside around Rankinston includes Kerse Loch.
Diagnose, treat, sign off
Our CSCS-carded applicators arrive with the sealants, primers and backing rod the job calls for. Joint faces are cleaned back to sound, dry surfaces, the manufacturer’s primer is applied where it’s called for, and the sealant is tooled off neatly. Jobs near Rankinston are often grouped with others in the same area. Let us know if your dates have any give.
- We start with your penetration schedule, drawings or specification.
- Access, permits and the order of areas are agreed with the site team.
- We compare every service penetration with its tested detail before sealing.
- Foam, ordinary sealant and debris come out.
- The specified backing and sealant go in to depth and are finished neatly.
- Anything outside the detail is reported to you rather than sealed.
What we need from you
- Send any specification or drawings in advance
- Share your working hours and any access restrictions
- Make sure the joints can be reached
Quotes
To get a fixed quote, phone 01277 525 020 or email us. Our quote form is another easy route.
Related advice
After the work
Once the work is signed off, a little attention goes a long way:
- Report damaged or disturbed seals as soon as they’re spotted
- Have penetrations checked while they can still be seen
- Leave fire sealant to cure fully before covering it
- Ask the designer to confirm details early on refits
Once the seals are in, tell other trades they exist and must not be disturbed. Any seal cut back for a new service needs reinstating to its tested detail.
The simplest way to keep compartment walls intact is to plan fire stopping into every job that crosses them. Then the seal goes in while the area is open, not months later.
How the quote is worked out
Before we quote, we look at:
- Induction, permit and paperwork requirements
- Location, for remote and island sites
- Quantities, in metres or numbers
- Any access equipment needed
The work involved drives the cost: removing old material, preparing the joints, the product, the access and how the work is phased. Call for a fixed quote.
What we need to price the job
A good diagnosis starts with the right details. Let us know:
- Whether the building will be occupied during the work
- Drawings or a marked-up plan, if available
- Any dates the work must fit around
- Asbestos survey details if the building is older
Photos, drawings or a schedule of the joints and a fixed quote comes back to you. Where a site visit makes more sense, we will arrange one.
Common questions from Rankinston clients
Is a smaller place like Rankinston outside your area?
No. Small places get the same service as large ones. We work across every Scottish council area. Send photographs and a list of what needs doing, and we’ll plan the job to need as few trips as possible.
How do Scotland’s building standards affect fire-rated sealant in Rankinston?
Scotland’s non-domestic Technical Handbook covers it in clause 2.1.14: penetrations keep at least the element’s fire resistance duration, with products tested for their end use. We install what has been specified, to the manufacturer’s tested detail, while design and approval sit with the designer and the verifier.
Will you just go over the old sealant?
No. Failed sealant is removed and the faces cleaned back to sound, dry material first, because fresh silicone will not bond with aged silicone.
How long does a job like this take?
The duration is planned around your programme and the access we’re given. We will give you an estimate of time on site when we quote.
Can you send site paperwork?
Tell us what site paperwork you need (RAMS, insurance certificate, CSCS details) and we will confirm with the quote.
Can you quote from photos?
Many jobs can be quoted from photos, drawings or a joint schedule. If the job needs a look first, we will arrange a visit before quoting.
How do you choose the sealant?
The specification comes first, if there is one. Without one, the joint decides: how much it moves, what it bonds to and whether it’s wet, trafficked or fire-rated.
Different surfaces, different methods
Cables and cable bundles
Data cabling added after handover is a regular cause of open service penetrations. Openings around new cables are resealed to the detail, and we tell you if the bundle exceeds what sealant covers.
Drylining partitions
Holes in board are often cut larger than needed. An oversized hole may be outside the sealant’s range and we’ll tell you what the detail says instead.
What we can’t put right
Being straight saves everyone time. Fresh joints won’t solve:
- Openings that need collars, wraps, batts or boards rather than sealant
- Signing off or certifying a building’s fire stopping
- Fire risk assessments, a job for a competent assessor
If you’re not sure, just ring 01277 525 020 or send photos by email and we will give you a straight answer.
Joints and surfaces we work on
- Pipe penetrations
- Joints between fire-resisting walls and floors
- Cable penetrations
- Service gaps in risers
- Linear gaps at wall heads
- Small duct penetrations where the tested detail allows