Fire Stopping in Cadham
Planning work on a service penetration in Cadham? We assess it, carry out the work and guarantee our workmanship for 12 months.
- Seals that don’t match their tested detail
- Unsealed penetrations discovered above suspended ceilings
- Seals disturbed by maintenance and left open
Fire stopping for Cadham sites
Send drawings, photos or a joint schedule, or tell us about the site, and we’ll come back with a fixed quote.
Work for main contractors and building owners
Main contractors use us as their sealant subcontractor, on new build and refurbishment alike. We work to your programme, your specification and your site rules, with CSCS-carded applicators on site.
Blocks and communal areas make up much of the work for housing associations and agents. Work can be phased so residents and staff keep access throughout, and each stage is agreed with your contact.
Fire stopping in Cadham
We should be clear about what we do and don’t do. The designer, fire engineer or building control decides which fire stopping is required; sign-off sits with them too. We fit the specified fire-rated sealant following that specification and the maker’s installation guidance. Most enquiries involve fire-rated sealant that has cracked or shrunk back and fire stopping installed outside its tested range, on joints between fire-resisting walls and floors, linear gaps at wall heads and service gaps in risers. A specialist sealant contractor works differently from a general builder: on jobs in Cadham, preparation and product choice get the time they need.
Around smaller places such as Cadham, compartment walls and floors tend to be in schools, hotels, care homes and community buildings. Those penetrations are closed with the product the specification names, built up as tested.
Every job is signed off with a 12-month guarantee. The promise is simple: if the work we did fails within twelve months, we return to fix it.
- Place
- Cadham (KY7, KY6)
- Region
- Fife
- Guarantee
- A 12-month guarantee
- Quotes
- Quoted before any work starts
- Telephone
- 01277 525 020
- Updated
- 3 November 2026
Maintenance after handover
A few simple habits keep the new joints working:
- Don’t let anyone top up a fire seal with the wrong product
- Brief every trade that openings they make must be sealed
- Look above ceilings when tiles are lifted for other jobs
- Flag new cables with no seal around them
After every round of M&E works, check that the openings created have been sealed. A short check at the end of each job saves a long hunt later.
Keep a register of where seals are and what they are made of. It tells the next contractor exactly what to reinstate.
From enquiry to sign-off
Before any cutting starts, the area is protected: tape along each joint edge and covers over finishes, stock and equipment close by. The work itself normally takes anything from one day to a planned run of visits, depending on the number of seals and the access, and we clear our waste as we work. Where we can, we combine work around Cadham with other jobs nearby, to make the most of each trip. Tell us how flexible your dates are.
- First we go through the drawings, schedule or specification for the seals and raise any questions before we price.
- On site, each opening is checked against the tested detail it is meant to follow.
- Unsuitable fillers and loose debris are taken out of each opening.
- Mineral wool or other backing goes in wherever the detail asks.
- Fire-rated or intumescent sealant is gunned in to the specified depth, then tooled.
- Openings that need a collar, wrap, batt or other product are flagged to you rather than filled with sealant.
What we need from you
- Move anything stored against the joints
- Tell us what induction or permit system the site runs
- Confirm the product named in the specification
Request a quote
Specifications, drawings and tender packages are welcome with any enquiry, and we’ll price against exactly what is specified. Smaller jobs need nothing more than photos and a few notes.
Read more
Do you need fire stopping in Cadham?
Some service penetrations were never sealed at all because they sat out of sight above a ceiling or inside a riser. Inspections, refurbishments and ceiling access usually bring them to light.
These are often picked up first by site or facilities staff:
- Fire sealant pulled out of the opening
- Damaged fire seals in risers and voids
- Builders’ foam or ordinary silicone in compartment walls
- Open linear gaps along the top of fire-resisting walls
Where a unit on an estate such as Queensway Industrial Estate, less than half a mile south of Cadham, has fire-resisting walls between offices and warehouse, any new service through them should be sealed to the tested detail.
What to look for in a quote
- Are they CHAS accredited or on Constructionline?
- The terms of the workmanship guarantee
- Will failed sealant be removed rather than covered?
- Whether their applicators hold CSCS cards
Your questions answered
Can you seal around new services in a hotel near Cadham?
Yes, to the specification and the product’s tested detail. It goes in to the manufacturer’s tested detail for the wall or floor and the services passing through, and we will tell you if the detail calls for a collar, wrap or batt instead.
Can you work at a site such as Queensway Industrial Estate, by Cadham?
Yes, sites like Queensway Industrial Estate are within our area, along with the rest of Cadham. A few photographs and the unit address let us price the work.
Does the weather affect the work?
It can, when the joints are outside. Wet joints and cold, damp or frosty conditions stop the sealant bonding properly, so external work may be moved if conditions aren’t right. Indoors, the weather is rarely a problem.
Can the sealant be colour-matched?
It depends on the product. Some ranges offer many colours, others very few, so the available colours are confirmed with the quote.
How much does the work cost?
It depends on the job: quantities, access, the product and any phasing. Call for a quote and we’ll price it properly.
Can you work to our specification?
Yes. Send it with your enquiry, and the quote will be based on it, flagging anything that needs clarifying.
Is the work guaranteed?
Yes, for 12 months. If a joint fails because of how we installed it, we come back and put it right.
Surface by surface
Metal pipes
Sealant details often cover copper and steel pipework. Pipe diameter, annular gap, sealant depth and any pipe insulation all have to match the detail, so we check each one.
Masonry and concrete
Core-drilled holes are neat; broken-out ones rarely are. Each gap is measured where it is widest against the detail’s limits.
When it isn’t the sealant
A proper diagnosis includes knowing what sealant can’t do. We will tell you if the real problem is one of these:
- Writing the fire-stopping specification
- Construction that lacks the fire resistance the seal relies on
- Signing off or certifying a building’s fire stopping
Not sure which it is? You can ring 01277 525 020 or send details through our quote form and we’ll tell you honestly.
Where we work in Cadham
- Small duct penetrations where the tested detail allows
- Joints between fire-resisting walls and floors
- Cable penetrations
- Pipe penetrations
- Linear gaps at wall heads
- Service gaps in risers
Compartment walls and floors in Cadham
There are plenty of hotels within about 2 miles of Cadham. Hotels are divided into compartments, and refurbishments that add pipes and cables through bedroom and corridor walls leave gaps to close. Scotland has its own building standards: the non-domestic Technical Handbook (clause 2.1.14) says service penetrations should be fire stopped to at least the fire resistance duration of the wall or floor, and products should be tested for their end use. We install fire-rated sealant to that tested detail where it is specified.
Theatres, wards and plant rooms at sites like Glenrothes Hospital, 0.6 miles to the north-west of Cadham, all have compartment walls crossed by services. Hotels like Golden Acorn Hotel (to the south of Cadham) are refurbished in phases, and each phase can open up compartment walls.
Cadham is about 1 mile north of Glenrothes, in Fife. Cadham sits inside our coverage, with the same fixed quotes and 12-month guarantee as everywhere else. 132 places across Fife fall within our area, including Cadham. Sites around Edinburgh have their own page, roughly 18 miles from Cadham.
Commercial sites across KY7 and KY6 are covered. Among the streets we cover are Elm Lane, Thane Road and Camby Road. You will find Cadham on or near the A911, so getting applicators and materials to site is simple. If your building is just outside Cadham, we cover Collydean (1 mile north-west), Markinch (1 mile east), Star (3 miles north-east), Freuchie (3 miles north) and Newton of Falkland (4 miles north). Bigger towns within reach include Dunfermline (14 miles south-west), Kirkcaldy (5 miles south), Leven (7 miles east), Cowdenbeath (9 miles south-west), Dysart (5 miles south) and Dalgety Bay (13 miles south-west).
What’s near Cadham
Recent enquiries here include premises near Riverside Park and The Golden Acorn pub and the streets around them. The closest station to Cadham is Markinch station, roughly 1.5 miles east of the centre. Well-known places in the area include Glenrothes Hospital (0.6 miles north-west) and Balgonie Castle (2.4 miles east). Green spaces nearby include East Lomond.