Fire-rated sealing and fire stopping in Brough, Shetland Islands
Sealant work in Brough for main contractors, managing agents and facilities managers: fire-rated and intumescent sealing of service penetrations and linear gaps, quoted at a fixed price.
- Snag lists that include open service penetrations
- Hidden openings found during inspections
- Fire sealant pulled out of the opening
Need fire stopping in Brough?
Send drawings, photos or a joint schedule, or tell us about the site, and we’ll come back with a fixed quote.
Questions about Brough
What do Scotland’s building standards say about service penetrations in Brough?
The non-domestic Technical Handbook, clause 2.1.14, expects a penetration to keep at least the wall or floor’s fire resistance period, with proprietary products tested for the use they’re put to. We install what has been specified, to the manufacturer’s tested detail, while design and approval sit with the designer and the verifier.
Do you decide the fire-stopping details for buildings in Brough?
No. The designer or fire engineer sets the detail and building control accepts it. We install fire-rated and intumescent sealant around service penetrations and linear gaps where it is specified, to the manufacturer’s tested detail.
What will the job cost?
Every job gets its own fixed quote. For yours, phone 01277 525 020 or send details through our quote form.
Do you seal on top of existing sealant?
No, never. Overlaying old sealant is a frequent cause of early failure, so everything comes out first.
Do you guarantee your work?
Yes. It runs for twelve months and covers how we prepared and sealed the joints, though not damage or work by other trades.
Do you take on multi-site work?
Yes. Several buildings can share a single quote, with one point of contact.
Do you offer coloured sealant?
It depends on the product specified. Some ranges offer many colours, others very few, so we will confirm the colours available for the specified product with the quote.
Fire stopping in Brough, done properly
Facilities managers in Brough often find open service penetrations when ceilings come down for other work. Where the walls and floors already have a fire-stopping specification, we can work to it using the product and detail it sets out. Where there isn’t one, the designer or fire engineer needs to set one first. We work on small duct penetrations where the tested detail allows, cable penetrations and linear gaps at wall heads, and the usual reasons a site gets in touch are builders’ foam or ordinary silicone in compartment walls and penetration schedules that need working through. Facilities teams, main contractors and managing agents in Brough tend to want the same three things: a clear scope, tidy work and joints that don’t fail again.
For a building near Brough, we plan fire-rated sealing so it’s finished in one visit where possible. Send the specification and photographs of the openings, with sizes if you have them.
We stand behind the joints we seal with a 12-month guarantee. It covers how we prepared and applied the sealant, and if something we did falls short, we return to it.
- Where
- Brough (ZE2)
- Wider area
- Shetland Islands
- Guarantee
- 12 months on our workmanship
- Price
- Fixed quote, scope in writing
- Telephone
- 01277 525 020
- Updated
- 3 November 2026
Keeping the joints sound
A few simple habits keep the new joints working:
- Flag new cables with no seal around them
- Record which product was used where
- Arrange inspection before areas are covered up
- Ask which product is in place before decorating
Never top up a fire seal with foam, ordinary silicone or filler. A repair should use the original product, installed the same way.
Ask every contractor who works in risers or voids to report openings they create. It costs little and catches breaches early.
Why deal with it now?
Leave a penetration open and smoke and fire can cross into the next compartment far earlier than intended. Putting it right is usually a modest job when the openings are accessible. Left until ceilings are closed or a tenant moves in, the same work costs more access and more disruption. Exposed buildings in Scotland take a lot of weather, and for a smaller place like Brough, a repair visit takes planning, so it’s better to act early.
The specified product makes a difference, as does the preparation each joint needs. Access, phasing and site requirements come into it too.
Why appoint us
- Clear, fixed quotes
- Old sealant cut out, never sealed over
- Workmanship guaranteed for 12 months
- CHAS accredited
Take a look at what affects the cost or our accreditations.
Site staff or a sealant specialist?
The visible bead is only part of the job. Correct depth, the right primer and a sealant matched to the movement are easy to get wrong without experience.
Using site staff can make sense for a small touch-up, but larger jobs are different: a specialist works through quantities efficiently, leaves a consistent finish and backs it with a 12-month guarantee.
What sealant work can’t fix
Before quoting, we check that sealant is the right answer. It isn’t the answer for:
- Designing or specifying fire stopping, which sits with the designer or fire engineer
- Construction that lacks the fire resistance the seal relies on
- Plastic pipes whose detail calls for a collar or wrap
If you are not sure, just phone 01277 525 020 or email us and we will give you a straight answer.
Surfaces we seal
- Service gaps in risers
- Linear gaps at wall heads
- Pipe penetrations
- Cable penetrations
- Small duct penetrations where the tested detail allows
- Joints between fire-resisting walls and floors
Do you need fire stopping in Brough?
Mixing products or improvising a detail breaks the link with the test evidence. An oversized gap, too shallow a bead, missing backing or two makers’ products combined are what we find most often.
Any of the following is a good reason to get the joints checked over:
- Head-of-wall gaps with no fire seal
- Non-fire-rated filler around services
- Fire-stopping items raised at inspection or handover
- Improvised or mixed-product fire seals
For buildings in and around Brough, fire-rated sealant is installed where it is specified, to the manufacturer’s tested detail.
What your quote should include
- What level of public liability insurance do they hold?
- Can the work be phased to keep areas open?
- How the existing material will be dealt with
- How joint depth will be controlled
Service penetrations in Brough buildings
Scotland has its own building standards: the non-domestic Technical Handbook (clause 2.1.14) says service penetrations should be fire stopped to at least the fire resistance duration of the wall or floor, and products should be tested for their end use. We install what’s specified, to the product’s tested detail. For an island location such as Brough, work is planned around ferry crossings and the weather. With the specification and photographs of the openings, the right fire-rated products travel with us.
Older community buildings such as Whalsay Parish Church that have been rewired or given new heating can have service gaps through walls worth checking against the specification.
Brough is in the Shetland Islands. We cover Brough, with the same fixed quotes and 12-month guarantee as everywhere else. 63 places across the Shetland Islands fall within our area, Brough among them.
We cover the ZE2 postcode districts. If your site is on Houll and Tripwell or close by, send details and we’ll quote for service penetrations. Just outside Brough, we also work in Tripwell (1 mile south-west), Hamister (1 mile south-west), Huxter (2 miles south), Symbister (2 miles south-west) and Sandwick (2 miles south-west). For island and remote sites, travel and materials need planning ahead.
Around Brough
Green spaces nearby include Setter Hill and Loch of Houll.
How a job runs
Working in a building that stays open takes some planning. We sign and contain the area we’re in, with routes through the building left open and move on in phases so staff and visitors can carry on around us. Travel to smaller Scottish places like Brough is planned so the job is finished in one visit where possible, so photos, sizes and a full list matter. External joints need a dry spell as well.
- First we confirm the product and tested details named in the specification.
- Openings are measured and grouped by detail.
- Improvised fillers and failed sealant are removed.
- Mineral wool or other backing is fitted where required.
- We gun the sealant in to the specified depth around each service and tool it.
- We walk the completed areas with you and confirm the records agreed at quote stage.
Before we start on site
- Let us know about inductions and permits
- Tell us your opening times and when work is allowed
- For older buildings, check the asbestos register before work
Getting a fixed quote
Let us know the site, the scope and your timescale, and we will put a fixed quote together. The easiest way is to phone 01277 525 020 or email a schedule or drawings.