Fire stopping in Ardersier
Need fire stopping in Ardersier? It’s simple: send details, get a quote, we seal, guaranteed.
- Fire stopping installed outside its tested range
- Fire sealant pulled out of the opening
- Penetration schedules that need working through
Fire stopping in Ardersier
Send drawings, photos or a joint schedule, or tell us about the site, and we’ll come back with a fixed quote.
Site staff or a sealant specialist?
Redoing a failed joint usually costs more than getting it right at the outset, since all of it has to come out and the faces be cleaned back again. For that reason, many FMs and contractors use a sealant specialist from the outset.
For a quick touch-up, site staff may be fine, but larger jobs are different: a specialist works through quantities efficiently, leaves a consistent finish and backs it with a 12-month guarantee.
About our fire stopping in Ardersier
A lot of fire-stopping work comes after M&E installation, a refit or a tenant fit-out. New cable runs, replaced pipework and extra data routes all punch holes in compartment walls. Those on your schedule are closed with the specified product. We work on pipe penetrations, cable penetrations and linear gaps at wall heads, and what we’re called in for most is penetration schedules that need working through and seals disturbed by maintenance and left open. A single leaking joint is often how a building in Ardersier first comes to us: we look at the rest while we are there and tell you what we find.
Refurbishments in small hotels, schools and care homes around places like Ardersier can leave gaps around new services. A round of checks after M&E work is good practice, and any gaps found are sealed where fire-rated sealant is specified.
Every job is signed off with a 12-month guarantee. It’s a plain promise: if the work we did fails within twelve months, we return to fix it.
- Where
- Ardersier (IV2)
- Wider area
- Highland
- Guarantee
- 12 months on our workmanship
- Quotes
- A fixed quote before we start
- Call
- 01277 525 020
- Page updated
- 3 November 2026
Why act early in Ardersier
Open penetrations multiply: every new cable or pipe adds another. A schedule that is dealt with regularly stays manageable, rather than turning into a full building survey and reseal. Renewing every failing joint on one visit is the sensible approach for a place like Ardersier. Photos of each area help us quote the whole job.
The product called for affects the cost, and so does the preparation, such as cutting out, priming or new backing rod. Access, phasing and site requirements come into it too.
Why appoint us
- Commercial sealant work since 2005
- Products installed to the manufacturer’s instructions
- Fully insured, including public liability cover
- Constructionline member for supplier checks
Read how commercial sealant jobs are priced and our accreditations and insurance.
On site: what to expect
We follow your site rules from the start: signing in, inductions and any permit to work. With the paperwork done, we take the joints in the sequence agreed with you, and each area is checked before we leave it. Where we can, we combine work around Ardersier with other jobs nearby, to make the most of each trip. Tell us how flexible your dates are.
- We read the specification, drawings or penetration schedule you send.
- Every penetration is compared with its detail: wall or floor type, service, gap size and depth.
- Unsuitable fillers and loose debris are taken out of each opening.
- Mineral wool or other backing goes in wherever the detail asks.
- We apply the specified sealant to the depth and around the services as the detail shows.
- Openings that need a collar, wrap, batt or other product are flagged to you rather than filled with sealant.
Before we start on site
- Send any specification or drawings in advance
- Warn occupants and staff about the work
- Make sure the joints can be reached
Ask for a quote
For a fixed quote, call the office on 01277 525 020 or send photos by email. Our quote form is another easy route.
Related advice
When to call us in Ardersier
A common fault is a product that was never fire-rated in the first place: builders’ foam or ordinary silicone used to fill a hole. The opening looks sealed but has no fire test evidence behind it.
Things that usually lead to an enquiry:
- Improvised or mixed-product fire seals
- Fire-stopping items raised at inspection or handover
- Fire sealant pulled out of the opening
- Non-fire-rated filler around services
Where a unit on an estate such as Dalcross Industrial Estate (2.1 miles south-west of Ardersier), has fire-resisting walls between offices and warehouse, any new service through them should be sealed to the tested detail.
What to look for in a quote
- Is depth set with backing rod, or bond-breaker tape in shallow joints?
- Whether primer will be used where the manufacturer specifies it
- The terms of the workmanship guarantee
- The named product and why it was chosen
What else we do in Ardersier
Owners, agents and contractors
As a CHAS accredited contractor and Constructionline member, we make supplier vetting simple. Our insurance certificate can be sent along with the quote.
Facilities managers want contractors who arrive with the paperwork sorted. Let us know the documents you need (RAMS, insurance certificate, CSCS details) and we will confirm them with the quote.
Looking after the joints
Once the work is signed off, these steps help:
- Brief every trade that openings they make must be sealed
- File the specified details where the next contractor can find them
- Settle who seals which penetrations at the start of a project
- Look above ceilings when tiles are lifted for other jobs
Don’t patch a fire-rated seal with anything outside its tested detail. A repair should use the original product, installed the same way unless the designer specifies otherwise.
Looking at service areas on a regular cycle pays off. A cracked or disturbed seal found early is a small job.
Compartment walls and floors in Ardersier
Scottish guidance (non-domestic Technical Handbook, clause 2.1.14) asks that penetrations match at least the fire resistance period of the element they pass through, with proprietary products, intumescent ones included, tested for their end use. We install what’s specified, to the product’s tested detail.
For buildings in and around Ardersier, fire-rated sealant is installed where it is specified, to the manufacturer’s tested detail.
Ardersier is about 6 miles west of Nairn, in Highland. Looking for fire stopping in Ardersier? We can help. Ardersier is one of 256 places in Highland on our list. There’s a separate page for Aberdeen, roughly 77 miles from Ardersier.
Work on service penetrations is covered throughout IV2, for business premises of every kind. Streets here include Station Road, High Street and Cameron Drive, and sites on any of them can send details for a fixed quote. Just outside Ardersier, we also work in Croy (3 miles south), Rosemarkie (3 miles north-west), Fortrose (4 miles west), Avoch (5 miles west) and Cawdor (5 miles east). Nearby towns on our patch include Inverness (10 miles south-west), Nairn (6 miles east), Cradlehall (7 miles south-west), Merkinch (10 miles south-west), Dingwall (15 miles west) and Hilton (10 miles south-west). Island and remote sites need extra planning, with travel, ferry crossings where needed and weather to allow for, so mention the location when you phone 01277 525 020 or email the details over.
Near you in Ardersier
The nearest railway station is Inverness Airport station, roughly 2.3 miles south of the centre. A little further out are Highland Aviation Museum (2.1 miles south-west) and Chanonry of Ross (3.7 miles west). Open spaces near Ardersier include Loch of the Clans and Fairy Glen.
Ardersier: questions and answers
What do Scotland’s building standards say about service penetrations in Ardersier?
Under Scotland’s non-domestic Technical Handbook (clause 2.1.14), service penetrations should keep at least the wall or floor’s fire resistance duration, using products tested for their end use. The detail is set by the designer and goes through the warrant process; we install the specified product to its tested detail.
Will you take on work at estates like Dalcross Industrial Estate, close to Ardersier?
Yes. We cover Ardersier and the area around it, including industrial estates, business parks and retail parks such as Dalcross Industrial Estate. A few photographs and the unit address let us price the work.
How do I request a quote?
It works in four steps: send details, get a quote, we seal, guaranteed. The first step only needs photos and a postcode.
How long do sealant joints last?
There’s no fixed lifespan: movement, exposure, cleaning, traffic and the product all play a part. Treat them as maintenance items and inspect them regularly.
How many days will you need on site?
That varies with the scale of the job, though a typical visit typically takes longer where risers, ceiling voids or occupied floors have to be worked through in sequence. Larger or phased jobs take longer, and we will give you a timescale with the quote.
What if there’s asbestos in the old mastic?
The duty to manage asbestos sits with the building’s dutyholder, so we will ask for the register before work on an older building. If anything suspect turns up, we stop until it’s tested.
Will you quote for a small job?
Small jobs are welcome alongside larger packages. Send details for a fixed quote.