Expansion joint sealing in Clate
Expansion and movement joint sealing in walls, decks and floors throughout Clate and nearby, by CSCS-carded applicators. Fully insured and CHAS accredited.
- Hardened, cracked sealant on exposed facades
- Movement joints with split or torn sealant
- Sealant peeling off one face of the joint
Expansion joint sealing for Clate sites
Send drawings, photos or a joint schedule, or tell us about the site, and we’ll come back with a fixed quote.
Looking after the joints
To get the most from the new sealant:
- Inspect movement joints alongside other routine building checks
- Clear dirt from joint lines during routine cleaning
- Raise snow-clearing blades over deck joints where possible
- Avoid parking heavy plant or pallets on joint lines
Add every elevation, deck and floor joint to your inspection round. Early splits and edges starting to lift show up on a routine check, when they’re still cheap to deal with. Should you spot a problem, you can speak to us on 01277 525 020 or email a schedule or drawings and send a picture.
Floor joints with failed fillers break up quickly under wheels. Damaged edges make the floor rough and wear wheels faster and the broken length grows with every pass. Keeping the filler or sealant sound protects the floor.
Expansion joint sealing in Clate
We cover the full range of movement joints: brickwork and blockwork joints, precast and cladding panel joints, concrete joints, car park decks and ramps, podiums and floor movement joints. The product depends on the movement, the weather and anything that runs over it, and we’ll confirm the choice in the quote. We work on car park decks and ramps, cladding panel joints and brickwork movement joints, and the failures we’re asked to look at most are damp inside where a wall movement joint has failed and hardened, cracked sealant on exposed facades. For commercial sealant work in Clate, you deal with one contact from quote to sign-off, for single jobs and planned programmes alike.
For floor or movement joints around smaller places like Clate, we plan to finish in one visit where we can. Photos, approximate widths and what uses the floor help us bring the right materials.
What our 12-month guarantee covers is the way we did the job: preparation, application and finish. It doesn’t extend to damage, other trades’ later work or movement the joint was never designed to take.
- Where
- Clate (ZE2)
- Wider area
- Shetland Islands
- Guarantee
- 12 months on every job
- Price
- A fixed quote before we start
- Telephone
- 01277 525 020
- Last updated
- 3 November 2026
Common questions from Clate clients
Our building in Clate is near the coast: does that change the sealant?
It can. Coastal exposure works external joints harder than inland weather. We choose the product for the exposure, prime where the manufacturer requires it and size the joint for its movement.
Will our site in Clate have to close for joint sealing?
Rarely. Work is phased around your operations. We agree the sequence and timings with you before we start.
Do you guarantee expansion joint work?
The workmanship is guaranteed for 12 months from sign-off. Regular sweeping and inspection help the joints last.
Do you reseal car park expansion joints?
Yes. These joints take wheels, salt and water, so product choice matters and broken edges are flagged before sealing.
Do you use silicone or polyurethane in movement joints?
The right product depends on the joint. Facades often take a low-modulus silicone; floors and decks typically need a polyurethane unless the specification names something else.
How long do sealant joints last?
It depends on movement, UV and weather, cleaning, traffic and the product. Sealant joints are maintenance items, so inspect them regularly.
Is Clate in your area?
Yes. Clate is in our area. To discuss a job, speak to us on 01277 525 020 or email the details over.
Expansion joint sealing around Clate: how the place shapes the job
With the shore within about 1 mile, Clate counts as a coastal location. External movement joints in car parks, ramps and yards near the coast take salt and wind-driven rain on top of traffic, so a failed joint lets more in and the edges break up sooner. Clate is in the east of Scotland, which is drier than the west. Frost and winter road salt still work into open joints in car parks and yards. Resealing before the cold months helps protect the edges.
A joint near Clate that has lost its sealant lets in water and grit, and the edges suffer next.
Clate is about 13 miles north of Lerwick, in the Shetland Islands. Across the ZE2 postcode area, the process is the same: send details, get a fixed quote, we seal, and the work is guaranteed. Clate is one of 63 places in the Shetland Islands on our list for movement joints.
We cover the ZE2 postcode districts for movement joints. We cover commercial and managed buildings on Rocky Road and Harlsdale. Sites close to Clate are covered too, including Sandwick (1 mile north), Symbister (1 mile north), Hamister (1 mile north), Huxter (1 mile east) and Tripwell (2 miles north-east). A short drive away, we cover Lerwick (13 miles south), Sound (14 miles south) and Brae (12 miles west). For island and remote sites, travel and materials need planning ahead, so include the location in your enquiry.
Local landmarks in Clate
Open spaces near Clate include Loch of Sandwick and Ward of Clett.
What sets the cost
Quotes vary with the job. Expect it to depend on:
- The total length or number of joints
- Any access equipment needed
- Whether the work must be split into stages
- Whether old sealant has to be cut out first
There’s no price list, because the scope varies so much from one building to the next. For a fixed figure, call for a quote and we will price your job on its own details.
Before you send an enquiry
A good diagnosis starts with the right details. Let us know:
- Clear photos of the problem areas
- The site address and postcode
- The type of building and who uses it
- Rough lengths or quantities, or drawings if you have them
Every quote starts with the facts: the joints involved, quantities, access and the product called for. Share whatever details you have and we will fill any gaps with a visit.
When something else is needed
Before quoting, we check that sealant is the right answer. It won’t put right:
- Movement on a scale no sealant is meant to absorb
- Proprietary pre-formed expansion joint systems
- Crumbling edges that would give a new bead nothing sound to grip
Not sure which it is? You can phone 01277 525 020 or send details through our quote form and we’ll tell you honestly.
Where we work in Clate
- Blockwork control joints
- Podiums and floor movement joints
- Precast concrete panel joints
- Car park decks and ramps
- Brickwork movement joints
- Cladding panel joints
When to bring in a specialist
Using site staff can make sense for a small touch-up, but larger jobs are different: a specialist brings efficiency, a consistent finish and a 12-month guarantee.
What you see is the finished bead, but most of the work is hidden. Correct depth, the right primer and a sealant matched to the movement are easy to get wrong without experience.
Do you need expansion joint sealing in Clate?
When a bead pulls away from one face, it has lost adhesion. Poor preparation, a skipped primer, or sealant bonded to the back of the joint are typical reasons.
These are often picked up first by site or facilities staff:
- Torn sealant in brick or block movement joints
- Expansion joints filled with dirt and stones
- Hardened, cracked sealant on exposed facades
- Damp inside where a wall movement joint has failed
Around Clate, each joint gets a filler or sealant matched to what crosses it and how much it moves.
What to look for in a quote
- How they handle RAMS and site documents
- Proof of insurance
- How joint depth will be controlled
- How they’ll work around occupants
What else we do in Clate
Diagnose, treat, sign off
We bring the products specified for the job, along with primers and backing rod. Joint faces are cleaned back to sound, dry surfaces, primer goes on where the manufacturer specifies it, and each bead is tooled to a neat concave finish. For work around Clate, we aim for one trip, so photos, sizes and a full list matter. Outside work also needs a suitable weather window.
- First the joints are inspected, widths measured and the type of failure noted.
- You receive a fixed quote stating the product and the movement it is rated for.
- Where areas have to stay open, we agree a phased sequence before starting.
- We strip the old sealant or filler and prepare each face until it’s sound and dry.
- Depth is controlled with backing, the faces are primed where the maker calls for it, then the bead is laid and tooled.
- We check each joint with you, confirm the cure time and sign off under our 12-month guarantee.
Before we start on site
- Let us know about inductions and permits
- Tell staff and tenants when we will be in
- Share your working hours and any access restrictions
Getting a fixed quote
The quickest route to a quote is a few photographs and the site postcode. Send them through the quote form, or call 01277 525 020 or email the details over to discuss it first.