Floor Joint Sealing contractors in Strome Ferry
We carry out floor joint sealing and filling in warehouses, factories and industrial units in Strome Ferry. Send photos or drawings for a fixed quote.
- Joint fill separating from the concrete
- Joint edges breaking up under truck wheels
- Unfilled floor joints collecting dirt and grit
Floor joint sealing near Strome Ferry
Send drawings, photos or a joint schedule, or tell us about the site, and we’ll come back with a fixed quote.
Slabs, ramps and loading bays in Strome Ferry
Strome Ferry lies within about 1 mile of the sea. Coastal yards and decks give their joints salt and wet weather to deal with, not just wheels, which is why split joints are worth sealing before the edges deteriorate. The west of Scotland, where Strome Ferry is, gets more rain than the east. External slab joints left open take plenty of rain. External sealing is booked for dry spells, with some give in the dates.
A joint near Strome Ferry that has lost its sealant lets in water and grit, and the edges suffer next.
Strome Ferry is in Highland. Businesses, contractors and managing agents in Strome Ferry can call on us for floor joints, as part of our coverage of Highland. Across Highland, 256 places are covered, Strome Ferry among them.
We take on floor joints across the IV53 postcode area, for business premises of every kind. Just outside Strome Ferry, we also work in Plockton (4 miles west), Lochcarron (4 miles north-east), Auchtertyre (5 miles south), Bundalloch (5 miles south-east) and Carndu (5 miles south-east). Remote and island addresses take more planning, from travel and ferries to the weather, so give the site location in your enquiry.
Near you in Strome Ferry
Strome Ferry has its own railway station: Stromeferry station. A little further out are Strome Castle (0.5 miles north). Open spaces near Strome Ferry include Loch na Leitire.
About our floor joint sealing in Strome Ferry
Forklifts and pallet trucks are hard on open joints. Each crossing knocks the unsupported edge until a crisp saw cut becomes a wide, broken groove. A properly filled joint carries the wheel over and protects both arrises, which is kinder to trucks, loads and operators. We work on forklift and pallet-truck routes, saw-cut induced joints and retail and showroom floors, and the failures we’re asked to look at most are scruffy, dirty joint lines on a shop or showroom floor and flexible sealant torn out by wheels. Most enquiries from Strome Ferry start with one failed joint and grow into a wider look at the building: we check the joints around it and give you an honest view of what needs doing now and what can wait.
Weather windows decide external joint work around a place like Strome Ferry: sealant needs a dry joint and a temperature within its range. Inside slabs aren’t affected and can be scheduled around the occupier.
A 12-month guarantee applies to all our work in Highland. If an installation problem shows up, call 01277 525 020 or email us and we will arrange a return visit.
- Location
- Strome Ferry (IV53)
- Wider area
- Highland
- Guarantee
- 12 months on every job
- Quote
- Fixed quote, scope in writing
- Call
- 01277 525 020
- Last updated
- 3 November 2026
Why it’s worth doing now in Strome Ferry
Dirt and spillage gather in open joints, out of reach of the floor cleaner. Where the floor is on show or needs to be kept clean, that is a problem. Filled joints are far simpler to keep clean. For buildings near Strome Ferry, dealing with all the failing joints at once saves return trips. Send photos and we will quote for everything together.
We don’t publish prices, because the scope varies so much from one building to the next. For a fixed figure, call for a quote.
What you get with us
- Products installed to the manufacturer’s instructions
- Constructionline member for supplier checks
- Work carried out by CSCS-carded applicators
- CHAS accredited contractor
Take a look at how commercial sealant jobs are priced or our accreditations and insurance.
What affects the price in Strome Ferry
There’s no standard rate for sealant work, because every site is different. What we look at:
- Phasing around occupants
- Induction, permit and paperwork requirements
- Removal of failed or old sealant
- The product specified
No two sites price the same: the joint sizes, the specified product, access and working hours each have a bearing. A fixed quote follows once we understand the job.
What to include in your enquiry
We can often quote from photographs and a few details. Please tell us:
- A wide shot and a close-up of the area
- The product your specification calls for
- Rough lengths or quantities, or drawings if you have them
- Your programme or deadline
To get a fixed quote, speak to us on 01277 525 020 or email a schedule or drawings, telling us the site location and the nature of the job. You can also send details through our quote form.
General trades versus a specialist
Putting right a botched joint often costs more than sealing it well at the start, since all of it has to come out and the faces be cleaned back again. That’s why many clients bring in a specialist from the beginning.
A short, simple internal joint is often within reach of a maintenance team. The usual problems come from preparation: new sealant over old, damp or dusty faces, or the wrong product for the movement.
When to call us in Strome Ferry
A slab keeps shrinking for a long time after it is cast, and saw-cut joints give that shrinkage a planned place to crack. As the panels contract, the joints widen so a filler put in early may separate along one side.
Most enquiries start with one or more of the following:
- Open saw cuts full of debris
- A gap opening alongside old joint filler
- Chipped and spalling edges along forklift routes
- A rough ride across broken joints
For floors and slabs around Strome Ferry, the product is chosen for the traffic and the movement at each joint.
Comparing quotes
- Will failed sealant be removed rather than covered?
- Are they CHAS accredited or on Constructionline?
- How joint depth will be controlled
- Is the sealant right for the movement and the substrate?
Diagnose, treat, sign off
On arrival, we sign in, go through any site induction and check how permits are handled. Everything around the joints gets protected before any cutting starts, with the work itself typically taking a day or more, depending on the metres of joint and how many zones the floor is split into. Jobs near Strome Ferry are often grouped with others in the same area, to make the most of each trip. Let us know if your dates have any give.
- We walk the floor and mark up joint widths, edge damage and traffic routes.
- You receive a fixed quote showing products and phasing.
- Each joint is cut or routed back to clean, sound concrete.
- We extract the dust and prime the faces if the product needs it.
- The joint is filled to its specified depth and trimmed level.
- We hand each phase back when it can take traffic.
Getting the site ready
- Make sure the joints can be reached
- Tell staff and tenants when we will be in
- Send asbestos survey details if the building is pre-2000
Ask for a quote
Send us photographs, drawings or a joint schedule and a fixed quote comes back to you. If the job needs a look first, we will arrange a site visit.
Advice
Towns and villages near Strome Ferry
Other services in Strome Ferry
Aftercare for building managers
To get the most from the new sealant:
- Keep trucks off new joints until we say they’re ready
- Ask drivers not to drag forks or pallets
- Start with the dock areas, where joints fail soonest
- Make joint checks part of your floor inspections
Normal floor cleaning is fine once the product has cured. If you use strong chemicals or hot-water washing, mention it when we quote so we choose something that tolerates them.
Treating joints while the arrises are sound keeps the work simple. Once they have broken away, edge repair comes first, with more downtime and more disruption.
FAQs: Strome Ferry
Is Strome Ferry off your patch?
No. Small places get the same service as large ones. Our area covers all of Scotland, cities, towns and islands alike. We plan jobs in smaller places so return trips are kept to a minimum.
Does a coastal location like Strome Ferry affect which sealant is used?
It can. Wind-driven rain and, closer to the shore, salt air are harder on external joints. We choose the product for the exposure, prime where the manufacturer requires it and size the joint for its movement.
What if there’s asbestos in the old mastic?
Managing asbestos is the dutyholder’s responsibility, so for older buildings we ask for the asbestos register first. If anything suspect turns up, we stop until it’s tested.
Can you phase floor joint work around operations?
In most cases, just the area being treated is coned off. Traffic returns to each zone once it has cured and the next zone follows.
Are you fully insured?
Yes. Mastic Doctor is fully insured, public liability included.
When can forklifts run over new joint filler?
Cure times vary with the product and the conditions. We will give you a time for each zone before we start.
Can weather delay the job?
It can, for external work. Sealant won’t bond properly to a wet or frosty joint, so external work may be moved if conditions aren’t right. Internal work is far less affected.