Facade Sealing in Strome Ferry
Facade joint and window perimeter sealing on commercial buildings across Strome Ferry, carried out by CSCS-carded applicators. Fully insured and CHAS accredited.
- Draughts around frames and panels
- Weathered joints at frame-to-structure perimeters
- Water coming in around window frames
Facade sealing near Strome Ferry
Photos, a specification or a quick description of the joints is enough to start a fixed quote.
Why act early in Strome Ferry
Patch repairs over old sealant tend to come back. A full cut-out and reseal costs more on the day but lasts much longer. Around smaller places like Strome Ferry, halls, stores and seasonal buildings may not be checked often, so a failed joint has time to cause damage. Resealing early avoids that.
The product called for affects the cost, as does the preparation each joint needs. Access, phasing and site rules also count.
Why clients in Strome Ferry choose us
- Standard and matched colours in many product ranges
- Constructionline member for supplier checks
- CSCS-carded applicators
- 12-month guarantee on workmanship
Take a look at how commercial sealant jobs are priced or our accreditations and insurance.
How we handle facade sealing in Strome Ferry
Most facade joint failures trace back to the joint, not just the sealant. Joint width needs to match how far the joint moves and how far the sealant can stretch, while rod fixes the depth and stops the bead sticking to the rear. We work on stone and brick facade joints, cladding panel joints and shopfront frames, and the failures we are asked to look at most are leaks at window and door perimeters and facade joints cracked through the middle. Whether you call it commercial sealant work, mastic application or joint sealing, in Strome Ferry it comes down to the same thing: the right product in a properly prepared joint.
Construction around smaller Scottish places like Strome Ferry is often one-off schemes: a school, a health centre, a hotel extension or a few houses. Exposed elevations in Scotland put facade and perimeter joints to work from day one, so the sealant choice matters.
Building owners and contractors get the same cover: twelve months on the work we carried out. It doesn’t extend to damage, faults in the building or work by others, and we are upfront about that.
- Location
- Strome Ferry (IV53)
- Region
- Highland
- Cover
- A 12-month guarantee
- Quotes
- A fixed quote before we start
- Call
- 01277 525 020
- Page updated
- 3 November 2026
On site: what to expect
A typical day starts with protection: masking tape along the joint edges and sheeting over anything nearby. On site, the work typically takes anything from a single day to several weeks, depending on joint lengths, access and the weather, and we clear our waste as we work. Where we can, we combine work around Strome Ferry with other jobs nearby. Tell us how flexible your dates are.
- We start with photographs, drawings or a visit to see the joints and agree access.
- Product choice follows the joint’s movement and substrate.
- The existing bead comes out in full.
- Primer is applied where the maker specifies it.
- Backing rod is fitted and the new sealant gunned in and tooled.
- We go over the completed work with you before leaving.
Before we start on site
- Have the specification and drawings to hand
- Tell us your opening times and when work is allowed
- Tell us which areas need to stay in use
Request a quote
Tell us about the building, the joints and when you need the work done, and a fixed quote will follow. The easiest way is to phone 01277 525 020 or email a schedule or drawings.
Read more
New build and refits around Strome Ferry
Strome Ferry lies within about 1 mile of the sea. On a coastal site, facade and perimeter joints face driven rain and, closer to the beach, salt, and the sealant, primer and backing need choosing with that in mind. Building work in Strome Ferry comes under the Building (Scotland) Regulations 2004 and their technical handbooks, with warrants from the local authority verifier. The mastic follows the specification that goes with the warrant.
Window perimeters and facade joints around Strome Ferry need correct width, depth and backing rod as much as a neat finish. Sites around Strome Ferry get mastic sealed to the drawings and the programme, nothing improvised.
Strome Ferry is in Highland. Anywhere in IV53, the process is the same: send details, get a fixed quote, we seal, and the work is guaranteed. Our Highland coverage takes in 256 places.
We take on facade joints across the IV53 postcode area, whatever the building. We also cover Plockton (4 miles west), Lochcarron (4 miles north-east), Auchtertyre (5 miles south), Bundalloch (5 miles south-east) and Carndu (5 miles south-east). Remote and island addresses take more planning, from travel and ferries to the weather, so give the site location in your enquiry.
Local landmarks in Strome Ferry
Strome Ferry has its own railway station: Stromeferry station. Well-known places in the area include Strome Castle (0.5 miles north). The countryside around Strome Ferry includes Loch na Leitire.
Questions about Strome Ferry
Does the sea air around Strome Ferry change the choice of sealant?
It can. Driven rain and salt are tougher on outside sealant than sheltered inland conditions. That puts more weight on product choice, primers where the manufacturer specifies them, and correct joint sizing.
Is Strome Ferry off your patch?
No. Places such as Strome Ferry are covered as much as the big towns. Our area covers all of Scotland, cities, towns and islands alike. Where we can, we group nearby jobs to make the most of each trip.
Can you work while the building is occupied?
In most cases, yes. We phase the work so most of the building stays in use.
Do you hold CHAS accreditation?
Yes. We’re CHAS accredited, we’re a Constructionline member and we use CSCS-carded applicators.
Should we check old sealant for asbestos?
Some older mastics, especially in pre-2000 buildings, can contain asbestos. Check the asbestos register or survey before it is disturbed; if it’s suspected, work stops until it has been tested. Removal of asbestos isn’t something we do.
Do you replace windows or glass?
No. That work needs a glazing specialist. We reseal window perimeters, panel joints and frame-to-structure perimeters on commercial buildings.
Can you work to our specification?
Yes. Send it with your enquiry, and the quote will be based on it.
What the job involves on each surface
Window and door perimeters
Window and door perimeters make up most facade sealing work. A low-modulus neutral-cure product, chosen for the frame and wall, goes in, tooled to shed water.
Precast concrete panels
Precast panel joints have to absorb thermal and structural movement. A sealant of the right movement class goes in over backing rod.
Building owners, agents and FMs in Strome Ferry
Hotels, schools, healthcare sites, offices and retail units book us directly too. The work is planned around how the building runs, so the building keeps working while we do.
If you look after buildings for someone else, you need clear quotes and clear reporting. We quote a fixed sum, confirm the scope and walk the finished work with you or your representative, plus a 12-month guarantee.
Also near Strome Ferry
More services for Strome Ferry
Honest limits
Our job is the joint, not everything around it. Sealant alone won’t deal with:
- Movement beyond what any sealant can handle
- Water getting in through cracked render or porous masonry
- Replacing glass or failed glazing units
Not sure which it is? You can call 01277 525 020 or email us and we will tell you honestly.
Joints and surfaces we work on
- Perimeter joints where frames meet the structure
- Shopfront frames
- Cladding panel joints
- Stone and brick facade joints
- Coping and flashing joints
- Window and door perimeters
Site staff or a sealant specialist?
For a quick touch-up, site staff may be fine, but anything bigger is another matter: a specialist brings efficiency, a consistent finish and a 12-month guarantee.
General builders and handymen seal joints, but it isn’t their main trade. A specialist prepares properly, controls joint depth and picks a product with the right movement class, which is what makes a joint last.