Industrial and floor joint sealing in Longhope, Orkney Islands
Looking for floor joint sealing in Longhope? Send us the details for a fixed quote, backed by a 12-month guarantee on the work.
- Scruffy, dirty joint lines on a shop or showroom floor
- Unfilled floor joints collecting dirt and grit
- Filler that has parted from one face
Floor joint sealing near Longhope
Photos, a specification or a quick description of the joints is enough to start a fixed quote.
Floor joint sealing in Longhope, done properly
Most industrial slabs are divided into panels by saw-cut joints and construction joints, and each joint line is a weak edge that wheels run over all day. We fill or seal them with a product matched to the traffic and the movement, so the arrises are supported and grit stays out. Most enquiries involve loading bay joints breaking down and chipped and spalling edges along forklift routes, across joints along racking aisles, forklift and pallet-truck routes and retail and showroom floors. Facilities teams, main contractors and managing agents in Longhope tend to want the same three things: a clear scope, tidy work and joints that don’t fail again.
Travel to smaller places like Longhope is planned so the work is done in one trip where possible. Photos, approximate widths and what uses the floor help us bring the right materials.
The 12-month guarantee covers our workmanship: the preparation, the sealing and the tooling. Damage, later alterations by others and movement beyond what the joint was designed for sit outside it.
- Place
- Longhope (KW16)
- Wider area
- Orkney Islands
- Guarantee
- A 12-month guarantee
- Quotes
- A fixed quote before we start
- Call
- 01277 525 020
- Page updated
- 3 November 2026
Signs you need floor joint sealing in Longhope
Loading bay joints are exposed to wind, wet tyres and bigger temperature swings on top of the heaviest turning movements. They are often the first on a site to break down.
Any of the following is a good reason to get the joints checked over:
- Untidy open joints in a retail unit
- Drivers complaining about joints on a route
- Failing joints at loading bays and dock doors
- Old filler gone hard, cracked or loose
A joint near Longhope that has lost its sealant lets in water and grit, and the edges suffer next; we will tell you if the edges need repairing first.
Questions to ask before you book
- Their public liability cover
- Will RAMS and insurance details be available?
- How they’ll work around occupants
- Will failed sealant be removed rather than covered?
What sets the cost
Before we quote, we look at:
- Distance, for remote addresses
- How much existing material needs removing
- Any access equipment needed
- Site requirements such as inductions and permits
Every site prices differently: the joint sizes, the specified product, access and working hours each have a bearing. A fixed quote follows once we understand the job.
What to include in your enquiry
A good diagnosis starts with the right details. Let us know:
- When you need the work done
- Photos of the joints, close up and from further back
- Any specification or named product
- The postcode of the building
A handful of photos and a postcode is the fastest way to a quote. Upload them with the quote form, or speak to us on 01277 525 020 or email a schedule or drawings if you’d rather talk the job through.
Owners, agents and contractors
Hotels, schools, healthcare sites, offices and retail units come to us directly as well. The work is planned around how the building runs, so the building keeps working while we do.
When you manage a building on behalf of an owner, you need clear quotes and clear reporting. You get a fixed quote, an agreed scope and a walk round at the end, plus a 12-month guarantee.
More services for Longhope
Your questions answered
Must our site in Longhope stop work while the joints are done?
Normally not: we work in sections and hand each one back once it has cured. The phasing plan comes with the quote.
Can you take on a job in Longhope, on the island?
Yes. Islands are part of our area, Longhope included. We plan island jobs around the ferry and the forecast, and bring everything the job needs on the first crossing.
What happens if the joint edges are damaged?
Filling against broken edges doesn’t last. If the arrises have spalled, we’ll say they need repair before filling and set out how that affects the job.
How soon can traffic go back on the floor?
Each product has its own cure time, and cold floors slow it down. Phasing is planned with that in mind.
Does weather matter for sealant work?
It can, for external work. Sealant won’t bond properly to a wet or frosty joint, so we watch the forecast and rearrange outside work if we have to. Internal work is far less affected.
Why is there a gap next to the joint filler?
Young concrete carries on shrinking for a long time, so a semi-rigid filler can part from one face. It is usually dealt with by topping up.
Will we need to close the floor?
The work is phased. Areas are taken out of use a section at a time around the site hours and access windows you give us.
Diagnose, treat, sign off
Inspect, seal, sign off: that’s the shape of every visit. First comes an inspection and agreement on scope, then we prepare and seal each joint with the specified product, and the job ends with a walk round and sign-off. Travel to smaller Scottish places like Longhope is planned so the job is finished in one visit where possible, so photos, sizes and a full list matter. External joints need a dry spell as well.
- We agree the traffic routes and phasing with your site team.
- We point out joints whose edges need repairing first.
- Failed material and debris are removed and the joint cleaned.
- We fill the joints with the agreed product, finished level.
- You get a time for each zone to reopen.
Before we start on site
- Tell us which areas need to stay in use
- Share the asbestos register for older buildings
- Point out parking and an unloading spot
Get a fixed quote
To get a fixed quote, speak to us on 01277 525 020 or email us. You can also send details through our quote form.
Read more
How the job changes by surface
Semi-rigid joint fillers
A semi-rigid fill can separate along one side while a slab is still shrinking. A later top-up normally puts that right, and we will explain it when we quote.
Saw-cut induced joints
Saw cuts are made soon after the slab is cast so shrinkage cracks follow a line. They are narrow but open up as the panels shrink so trafficked runs need a filler that holds the arrises.
Honest limits
Before quoting, we check that sealant is the right answer. It won’t put right:
- Uneven floors that need grinding or levelling
- Wide or random cracking that suggests a structural issue
- A failing floor coating, which is a flooring contractor’s job
Not sure which it is? You can give us a call on 01277 525 020 or send details through our quote form and we’ll tell you honestly before you book.
Surfaces we seal
- Forklift and pallet-truck routes
- Retail and showroom floors
- Construction joints
- Saw-cut induced joints
- Loading bays
- Joints along racking aisles
Warehouse floors and decks around Longhope
Longhope sits close to the coast, within about 1 mile. Near the sea, external slabs, ramps and decks see salt air and driven rain as well as their usual loads, and edges left open tend to break up faster. Longhope is on Scotland’s drier eastern side. Frost and de-icing salt still find their way into open external joints. Autumn is a sensible time to seal them.
In and around Longhope, the right filler or sealant for each joint depends on the traffic and the movement it takes.
Longhope is about 15 miles south-west of Kirkwall, in the Orkney Islands. We cover commercial sites throughout Longhope, whether it’s a single job or part of a planned programme. We work across 51 places in the Orkney Islands, large and small.
If you need floor joint sealing in KW16, the process matches everywhere else we work: details, then a fixed price, then sealing and a 12-month guarantee. Just outside Longhope, we also work in Lyness (2 miles north), Scarfskerry (11 miles south), Rattar (11 miles south), Brough (12 miles south-west) and Canisbay (12 miles south). Island and remote sites need extra planning, with travel, ferry crossings where needed and weather to allow for, so give the site location in your enquiry.
What’s near Longhope
Nearby you will also find Longhope Lifeboat Museum (1.5 miles south-west). Not far away are Binga Fea and Loch of Greenhill.