Fire stopping in Wilton Dean
Fire-rated and intumescent sealing of service penetrations and linear gaps across Wilton Dean, by CSCS-carded applicators. Fully insured and CHAS accredited.
- Non-fire-rated filler around services
- Open linear gaps along the top of fire-resisting walls
- Penetration schedules that need working through
Fire stopping for businesses in Wilton Dean
Share the site address and what’s failing, and we’ll reply with a fixed quote or arrange a visit.
About our fire stopping in Wilton Dean
Most of our fire stopping work happens after the building is up. New cable runs, replaced pipework and extra data routes all punch holes in compartment walls, and they are easy to forget. We close the openings listed on your schedule, using the specified sealant and detail. We work on joints between fire-resisting walls and floors, cable penetrations and service gaps in risers, and the failures we are asked to look at most are unsealed penetrations discovered above suspended ceilings and builders’ foam or ordinary silicone in compartment walls. Looking for mastic applicators who cover Wilton Dean? We have been sealing commercial buildings since 2005, with CSCS-carded applicators.
Refurbishments in small hotels, schools and care homes around places like Wilton Dean can leave gaps around new services. A round of checks after M&E work is good practice, and any gaps found are sealed where fire-rated sealant is specified.
Building owners and contractors get the same cover: twelve months on the work we carried out. Faults in the structure, damage and other trades’ work fall outside it, and we say so plainly.
- Place
- Wilton Dean (TD9)
- Wider area
- Scottish Borders
- Guarantee
- 12 months on our workmanship
- Quotes
- A fixed quote before we start
- Telephone
- 01277 525 020
- Page updated
- 3 November 2026
Compartments and services around Wilton Dean
Under the Scottish non-domestic Technical Handbook, clause 2.1.14, penetrations should be fire stopped to at least the wall or floor’s fire resistance duration, and products should be tested for their end use. We install what’s specified, to the product’s tested detail. Wilton Dean has two care or nursing homes no more than 2 miles away. Care settings depend on compartmentation, so service penetrations made during maintenance or refurbishment need sealing with the specified product.
Older community buildings such as Old Parish Church that have been rewired or given new heating can have service gaps through walls worth checking against the specification. At a healthcare site like Hawick Community Hospital, which lies east of Wilton Dean, new services through compartment walls are a constant, and each needs the specified seal.
Wilton Dean is about 1 mile west of Hawick, in the Scottish Borders. If you’re looking for fire stopping in Wilton Dean, we can help. We work across 91 places in the Scottish Borders, from busy centres to rural villages. We also cover Edinburgh, around 39 miles from Wilton Dean.
Business premises anywhere in TD9 are within our area for service penetrations. Among the streets we cover are Dean Road, Overhall Road and Buccleuch Road, and sites on any of them can send details for a fixed quote. We also cover Wilton (1 mile east), Hawick (1 mile east), Stirches (1 mile north-east), Burnfoot (2 miles north-east) and Newmill (4 miles south-west) for service penetrations. A short drive away, we cover Galashiels (13 miles north), Selkirk (9 miles north), Jedburgh (11 miles east), Melrose (12 miles north), Langlee (13 miles north) and St Boswells (12 miles north-east).
Near you in Wilton Dean
Locally, jobs take us to sites close to The Bourtree pub. Well-known places in the area include Borders Textile Towerhouse (0.7 miles east) and Branxholme Castle (2.5 miles south-west). Green spaces nearby include Williestruther Loch and Ashkirk Hill.
What the job involves on each surface
Small ducts
Some fire-rated sealant details cover small ducts. Larger or fire-rated ductwork typically needs a different solution set by the designer, and we’ll say if that applies.
Plastic pipes
Plastic waste pipes through slabs come up often. Whether sealant alone is acceptable depends entirely on the tested detail, and we won’t substitute it for a specified collar.
Do you need fire stopping in Wilton Dean?
Linear gaps fail where a fire-resisting wall meets a slab, soffit or another wall. Movement in the frame or slab can open the joint, and a product not tested for that movement may crack. The tested detail for a linear joint states the width and movement it covers.
Any of the following is a good reason to get the joints checked over:
- Snag lists that include open service penetrations
- Improvised or mixed-product fire seals
- Fire seals cut back for extra cables and never reinstated
- Openings found when ceilings come down for a refit
For a hotel such as Balcary House Hotel (less than half a mile south-east of Wilton Dean), penetration seals are worth checking after any refit or services upgrade.
Comparing quotes
- Their approach to joint depth and backing
- Is the sealant right for the movement and the substrate?
- Are they CHAS accredited or on Constructionline?
- What level of public liability insurance do they hold?
FAQs: Wilton Dean
Is a smaller place like Wilton Dean outside your area?
Not at all. Wilton Dean is within our area. Our area covers all of Scotland, cities, towns and islands alike. Send photographs and a list of what needs doing, and we’ll plan the job to need as few trips as possible.
Will you take on work at estates like Hawick Business Centre, close to Wilton Dean?
Yes, sites like Hawick Business Centre are within our area, along with the rest of Wilton Dean. Photos and a short description are enough for a first look.
When is resealing likely to be due?
There’s no fixed lifespan: movement, exposure, cleaning, traffic and the product all play a part. Sealant joints are maintenance items, so inspect them regularly.
Can you seal any opening with fire-rated sealant?
No. Each fire-rated sealant is tested for particular services, gap sizes and substrates. If an opening falls outside, it needs another solution, as set out by the designer.
Do you guarantee your work?
Yes. Workmanship is guaranteed for 12 months.
When can the area be used after sealing?
We will confirm how long the chosen product needs to cure.
Which sealant will you use?
If the job is specified, we follow the specification. Otherwise, we recommend a product to suit the joint’s movement, the substrate and the conditions, following the manufacturer’s guidance.
Also in Wilton Dean
How the quote is worked out
To price the job, we consider:
- Distance, for remote addresses
- How accessible the joints are
- The site’s rules and procedures
- Quantities, in metres or numbers
What a job costs comes down to the quantity of joints, how much old material needs removing and how the joints are reached. Call for a quote once you have the details.
Sending details for a quote
Good information means a firmer quote. When you get in touch, include:
- Where the site is, with the postcode
- The asbestos register, for older buildings
- The product your specification calls for
- Your programme or deadline
Quotes are fixed against the scope you send, so you know the figure before anyone is on site. To start the process, call 01277 525 020 or email drawings and photos.
Looking after the joints
After handover, a little attention goes a long way:
- Agree the fire-stopping specification before services go in
- Look above ceilings when tiles are lifted for other jobs
- Put resealing into every M&E and fit-out package
- Don’t let anyone top up a fire seal with the wrong product
Store the specified product details somewhere the next contractor can find them. It makes later repairs much easier to match.
Specify fire stopping early on refits, not as an afterthought. Details can then be picked to suit the actual pipes, cables and ducts, and installation follows the programme.
On site: what to expect
Diagnose, treat, sign off: every visit follows that pattern. We inspect the joints and confirm what’s in scope, then we prepare and seal each joint with the specified product, and the job ends with a walk round and sign-off. Tell us who will meet us and how to get in at your building near Wilton Dean. That goes into the plan alongside the quote.
- We ask for the product and detail your designer has specified.
- Openings are measured and grouped by detail.
- Improvised fillers and failed sealant are removed.
- Where the detail needs backing, it goes in at the stated depth.
- We gun the sealant in to the specified depth around each service and tool it.
- We walk the completed areas with you and confirm the records agreed at quote stage.
Before we start on site
- Let building users know which areas are affected
- Point out parking and an unloading spot
- Let us know about inductions and permits
Get a fixed quote
The quickest route to a quote is a few photographs and the site postcode. Upload them with the quote form, or phone 01277 525 020 or email a schedule or drawings if you’d rather talk the job through.
Read more
General trades versus a specialist
There’s also the paperwork. Many sites expect CSCS cards, RAMS and proof of insurance, and we’ll confirm the paperwork you need with the quote.
The visible bead is only part of the job. Correct depth, the right primer and a sealant matched to the movement are easy to get wrong without experience.