Fire stopping in Tiptoe
Fire-rated and intumescent sealing of service penetrations and linear gaps across Tiptoe, carried out by CSCS-carded applicators. Fully insured and CHAS accredited.
- Unsealed penetrations discovered above suspended ceilings
- Seals that don’t match their tested detail
- Head-of-wall gaps with no fire seal
Fire stopping for Tiptoe sites
Tell us what needs sealing and where, with photos or drawings if you have them, and we’ll price it.
Different surfaces, different methods
Risers and ceiling voids
Openings above suspended ceilings are easy to miss. We follow your schedule area by area, and note anything we find that isn’t on it.
Small ducts
Small ductwork can sometimes be sealed with sealant where the tested detail includes it. Bigger ducts and fire-resisting ductwork are normally handled with other products and we flag that rather than guess.
How we handle fire stopping in Tiptoe
It helps to set out our role at the start. The designer, fire engineer or building control decides which fire stopping is required. What we bring is careful installation of the specified sealant, to the maker’s guidance on buildings around Tiptoe. If you are dealing with unsealed penetrations discovered above suspended ceilings and service penetrations left open after M&E works, we can put it right, whatever the surface. Looking for mastic applicators who cover Tiptoe? We’ve been sealing commercial buildings since 2005.
Smaller places such as Tiptoe still have buildings with fire-resisting walls and floors: schools, halls, care homes and commercial conversions. If sealant is what the specification names, we install it around the services exactly as the maker’s detail sets out.
We stand behind the joints we seal: 12 months, guaranteed. It covers how we prepared and applied the sealant, and if something we did falls short, we return to it.
- Location
- Tiptoe (SO41)
- Wider area
- Hampshire
- Guarantee
- 12 months on our workmanship
- Price
- Quoted before any work starts
- Phone
- 01277 525 020
- Last updated
- 3 November 2026
Fire stopping around Tiptoe: points for this area
The area within 2 miles of Tiptoe holds several hotels. Bedroom-to-corridor walls in hotels are normally fire-resisting, so new cabling or pipework through them has to be sealed to the tested detail. For England, the fire stopping of penetrations is dealt with in Approved Document B. References to the older BS 476 classes are being removed from it from 2 September 2029, after which the European classification, BS EN 13501-2, is the route, subject to transitional arrangements. We install whatever has been specified, to the product’s tested detail.
In a hotel such as Forest Heath Hotel (1.1 miles east of Tiptoe), new pipework or cabling through bedroom and corridor walls needs sealing with the specified product. In a building such as St Andrew, any service penetration through a fire-resisting wall should be sealed to the specified detail.
Tiptoe is about 4 miles north-west of Lymington, in Hampshire. Our applicators travel to Tiptoe for work on service penetrations, handled exactly as we handle every other area. Our Hampshire coverage takes in 723 places. We also cover Southampton, some 14 miles away.
Work on service penetrations is covered throughout SO41, for business premises of every kind. Streets here include Middle Road, Crabbswood Lane and Wootton Road. Nearby places we also cover include Mead End (1 mile north), Sway (1 mile north-east), Bashley (1 mile west), Ashley (1 mile south-west) and Hordle (2 miles south). Bigger towns within reach include Totton (11 miles north-east), Lymington (4 miles south-east), Hythe (12 miles north-east), Ringwood (8 miles north-west), Barton on Sea (3 miles south-west) and Dibden Purlieu (11 miles north-east).
Near you in Tiptoe
Recent enquiries here include premises near The Plough Public House and The Arnewood School, among other places. The closest station to Tiptoe is Sway station, roughly 1 mile north-east of the centre. Other landmarks nearby include Sammy Miller Motorcycle Museum (2.1 miles south-west) and Highcliffe Castle (4.6 miles south-west). Green spaces nearby include Milford on Sea LNR.
Tiptoe: questions and answers
Is a smaller place like Tiptoe outside your area?
Not at all: smaller places are covered as well as towns. London and every South East county are within our area. Where we can, we group nearby jobs to make the most of each trip.
What happens to BS 476 references for fire stopping in Tiptoe?
References to BS 476 classes are being removed from Approved Document B from 2 September 2029, after which BS EN 13501-2 classification is the route, subject to transitional arrangements. Whichever applies, we install the specified product to its tested detail; the specification is for the designer to set.
How long will the new sealant last?
There’s no fixed lifespan: movement, exposure, cleaning, traffic and the product all play a part. Treat them as maintenance items and inspect them regularly.
When can the area be used after sealing?
The product and site conditions decide that. Some products skin over quickly but need longer to cure fully, and we confirm it before leaving site.
What happens if old sealant might contain asbestos?
Asbestos is possible in some older mastics, particularly in buildings from before 2000. Before we disturb old sealant in an older building, we ask to see the asbestos register or survey, and if asbestos is suspected, work stops until it’s tested. Removing asbestos is a job for asbestos specialists, not us.
Do you offer coloured sealant?
In many cases, yes. Many products come in a range of standard colours, and matching to RAL references or surrounding finishes is often possible. We confirm what’s available for the specified product when we quote.
Are you CHAS accredited?
Yes. CHAS accredited, Constructionline member, and our applicators hold CSCS cards.
On site: what to expect
Where the site stays busy, we agree a sequence with your contact so the disruption stays in one area at once. Each section is protected, cleaned back and sealed before we move to the next. For work around Tiptoe, we aim to finish in one visit, so we ask for photographs and rough sizes first. That way the right products come on the day.
- We start with your penetration schedule, drawings or specification.
- Access, permits and the order of areas are agreed with the site team.
- We compare every service penetration with its tested detail before sealing.
- Unsuitable material is removed and the opening cleaned.
- Backing and fire-rated sealant are installed to the detail and tooled.
- We tell you about openings that need a different product.
Getting the site ready
- Make sure the joints can be reached
- Point out any areas we must not close
- Tell us your opening times and when work is allowed
Getting a fixed quote
Pricing a project or setting a maintenance budget? We will quote against your scope and drawings that you can work with. If you have questions first, call the office on 01277 525 020 or use the quote form.
Advice
When to bring in a specialist
For a quick touch-up, site staff may be fine, but larger jobs are different: a specialist works through quantities efficiently, leaves a consistent finish and backs it with a 12-month guarantee.
General builders and handymen seal joints, but it isn’t their main trade. A specialist prepares properly, controls joint depth and picks a product with the right movement class.
What we are called out for in Tiptoe
Most open service penetrations are left by later work. New cabling, rerouted pipework or a data route drilled through a riser leaves an opening that nobody returns to. Across several fit-outs, the openings add up.
If one of these sounds familiar, it’s time for a closer look:
- Open linear gaps along the top of fire-resisting walls
- Openings found when ceilings come down for a refit
- Unsealed openings around new pipes and cables
- Fire seals cut back for extra cables and never reinstated
Where a unit on an estate such as Gore Road Industrial Estate (2.5 miles south-west of Tiptoe), has fire-resisting walls between offices and warehouse, any new service through them should be sealed to the tested detail.
Questions to ask before you book
- How joint depth will be controlled
- What site paperwork they can supply
- What the guarantee covers, and for how long
- Proof of insurance
What else we do in Tiptoe
When it isn’t the sealant
Being straight saves everyone time. Fresh joints won’t solve:
- Reviewing a building’s overall fire safety
- Designing or specifying fire stopping, which sits with the designer or fire engineer
- Issuing fire ratings or certificates for seals
If in doubt, give us a call on 01277 525 020 or use the quote form and we’ll say what we think before you book.
What we seal
- Pipe penetrations
- Service gaps in risers
- Cable penetrations
- Linear gaps at wall heads
- Joints between fire-resisting walls and floors
- Small duct penetrations where the tested detail allows
Owners, agents and contractors
Building owners and managing agents use us on sealant work across single buildings or whole portfolios. One quote can cover more than one site, which keeps the paperwork simple.
Agents, factors and owners’ representatives all follow the same route: send the details, accept a fixed quote, and we carry out and guarantee the work. Keys, access and contacts can be agreed in advance.