Kinlochbervie fire stopping
Fire-rated and intumescent sealing of service penetrations and linear gaps in Kinlochbervie and across Highland. CHAS accredited and fully insured, with a 12-month guarantee.
- Non-fire-rated filler around services
- Fire seals cut back for extra cables and never reinstated
- Fire sealant pulled out of the opening
Fire stopping near Kinlochbervie
Share the site address and what’s failing, and we’ll reply with a fixed quote or arrange a visit.
Site staff or a sealant specialist?
There’s also the paperwork. Main contractors and clients often ask for CSCS cards, RAMS and insurance details, and we will confirm the paperwork you need with the quote.
Site maintenance staff can often handle a short internal joint. Where it goes wrong is preparation: new sealant over old, damp or dusty faces, or the wrong product for the movement.
Fire stopping for commercial buildings in Kinlochbervie
A fire-rated sealant is only one part of a tested system: the evidence covers a specific product, wall or floor type, service, gap, depth and backing. We match each opening to that detail before any sealant goes in, and we say so if it doesn’t fit. If you have non-fire-rated filler around services and open linear gaps along the top of fire-resisting walls, we can put it right, on service gaps in risers, linear gaps at wall heads and joints between fire-resisting walls and floors alike. Most enquiries from Kinlochbervie start with one failed joint and grow into a wider look at the building: we look at the rest while we are there and tell you what we find.
Hotels and care homes around smaller places like Kinlochbervie often have services added during refurbishment. A round of checks after M&E work is good practice, and any gaps found are sealed where fire-rated sealant is specified.
We sign every job off with a 12-month guarantee. The promise is simple: if the work we did fails within twelve months, we return to fix it.
- Location
- Kinlochbervie (IV27)
- Wider area
- Highland
- Cover
- 12 months on our workmanship
- Price
- A fixed quote before we start
- Phone
- 01277 525 020
- Page updated
- 3 November 2026
What happens if it’s left?
An open or wrongly sealed service penetration lets fire and smoke reach the next compartment much sooner than the building was designed for. While the openings can be reached, sealing them is normally straightforward. Wait until ceilings close or areas are occupied and the same work becomes harder to reach. Exposed buildings in Scotland take a lot of weather, so it’s worth renewing joints around Kinlochbervie before they leak.
Access often affects the price as much as the sealing: easy-to-reach joints are quicker than those that need equipment to get to. Mention the access as part of your enquiry.
Why clients in Kinlochbervie choose us
- Fixed quotes based on photographs, drawings or a visit
- Workmanship guaranteed for 12 months
- One phone line for London, the South East and Scotland
- Fully insured, including public liability cover
Read what affects the cost and our accreditations and insurance.
Places near Kinlochbervie
More services for Kinlochbervie
Work for main contractors and building owners
Hospitality, education, healthcare, office and retail clients book us directly too. We plan around the way the building is used, so guests, pupils, patients or staff are disturbed as little as possible.
For main contractors, we work as the sealant subcontractor on new-build and refurbishment projects. We work to your programme, your specification and your site rules, and our applicators hold CSCS cards.
What the job involves on each surface
Masonry and concrete
Openings through concrete vary from tidy cores to rough break-outs. Each gap is measured where it is widest so we know it sits within the tested range, and any that don’t are flagged.
Linear joints
Linear joints run along the head of a wall, at a slab edge or between two fire-resisting elements. Their tested detail, under BS EN 1366-4, sets the width, depth, backing and movement allowed, and we work within it.
Fire stopping around Kinlochbervie: what changes locally
Scotland has its own building standards: the non-domestic Technical Handbook (clause 2.1.14) says service penetrations should be fire stopped to at least the fire resistance duration of the wall or floor, and products should be tested for their end use. We install what’s specified, to the product’s tested detail.
Schools such as Kinlochbervie High School often have new data and services installed during holidays, and penetrations through fire-resisting walls should be checked afterwards. Hotels like Kinlochbervie Hotel, under half a mile north-west of Kinlochbervie, are refurbished in phases, and each phase can open up compartment walls.
Kinlochbervie is in Highland. Our applicators travel to Kinlochbervie for work on service penetrations, handled exactly as we handle every other area. We work across 256 places in Highland, from busy centres to rural villages.
Work on service penetrations is covered throughout IV27, whatever the building. For a building on Innes Place, Inchard Place and Manse Road or nearby, send details and we will quote for service penetrations. Close to Kinlochbervie, our area also takes in Scourie (8 miles south-west), Scourie More (9 miles south-west), Diuranais (13 miles north-east), Smoo (13 miles north-east) and An Druim Beag (16 miles south). Where a site is remote or on an island, we plan travel and materials carefully, so the full address helps from the start.
Around Kinlochbervie
For a walk, there’s Loch Càrn Mharasaid.
Questions we are asked in Kinlochbervie
What do Scotland’s building standards say about service penetrations in Kinlochbervie?
Under Scotland’s non-domestic Technical Handbook (clause 2.1.14), service penetrations should keep at least the wall or floor’s fire resistance duration, using products tested for their end use. We install what has been specified, to the manufacturer’s tested detail, while design and approval sit with the designer and the verifier.
Do you design the fire stopping for buildings in Kinlochbervie?
No. The designer or fire engineer sets the detail and building control accepts it. We install fire-rated and intumescent sealant around service penetrations and linear gaps where it is specified, to the manufacturer’s tested detail.
Who decides which product is used?
If the job is specified, we follow the specification. Otherwise, we recommend a product to suit the joint’s movement, the substrate and the conditions, following the manufacturer’s guidance.
What about RAMS and site documents?
Tell us what site paperwork you need (RAMS, insurance certificate, CSCS details) and we will confirm with the quote.
Do you guarantee your work?
Yes. The 12-month guarantee covers our preparation and application, but not damage, misuse or other trades’ work.
Is colour matching possible?
It depends on the product. Some ranges offer many colours, others very few, so we will confirm the colours available for the specified product with the quote.
Do you hold CHAS accreditation?
Yes. CHAS accredited, Constructionline member, and our applicators hold CSCS cards.
Common problems we fix in Kinlochbervie
Mixing products or improvising a detail breaks the link with the test evidence. Gaps beyond the tested size, shallow sealant, no backing where it was needed, or products from different systems mixed together are the usual culprits.
Things that normally lead to an enquiry:
- Fire seals cut back for extra cables and never reinstated
- Service penetrations left open after M&E works
- Fire stopping installed outside its tested range
- Old intumescent sealant that has split away
In a building such as Church of Scotland Church, any service penetration through a fire-resisting wall should be sealed to the specified detail.
Comparing quotes
- Is depth set with backing rod, or bond-breaker tape in shallow joints?
- Are they CHAS accredited or on Constructionline?
- The terms of the workmanship guarantee
- Will failed sealant be removed rather than covered?
Our process
Inspect, seal, sign off: that’s the shape of every visit. We inspect the joints and confirm what’s in scope, then we prepare and seal each joint with the specified product, and the job ends with a walk round and sign-off. Travel to smaller Scottish places like Kinlochbervie is planned so the job is finished in one visit where possible, so photos, sizes and a full list matter. Outside work also needs a suitable weather window.
- The specification and schedule come first, so we know which details apply.
- Access, permits and the order of areas are agreed with the site team.
- Each opening is checked for wall or floor type, service, gap and depth.
- Foam, ordinary sealant and debris come out.
- The specified backing and sealant go in to depth and are finished neatly.
- We tell you about openings that need a different product.
Getting the site ready
- Tell us which areas need to stay in use
- Send your site hours and access windows
- Let us know about inductions and permits
Ask for a quote
Need a figure for a tender or a budget? We will quote against your scope and drawings that you can work with. If you have questions first, call the office on 01277 525 020 or email us.