Fire stopping in Cyprus
We carry out fire-rated and intumescent sealing of service penetrations and linear gaps in Cyprus. Send details for a fixed quote.
- Seals that don’t match their tested detail
- Expanding foam used as fire stopping
- Fire sealant pulled out of the opening
Fire stopping near Cyprus
Tell us what needs sealing and where, with photos or drawings if you have them, and we’ll price it.
General trades versus a specialist
A short, simple internal joint is often within reach of a maintenance team. The usual problems come from preparation: new sealant over old, damp or dusty faces, or the wrong product for the movement.
Paperwork matters too. Many sites expect CSCS cards, RAMS and proof of insurance, and our CSCS-carded applicators are used to working under those rules.
Fire stopping for commercial buildings in Cyprus
The test standards are BS EN 1366-3 for penetration seals and BS EN 1366-4 for linear joints, with results classified under BS EN 13501-2. A rating such as EI 60 only holds when the product is installed as it was tested. Reproducing the tested arrangement on site is the part we take care of. We work on joints between fire-resisting walls and floors, pipe penetrations and small duct penetrations where the tested detail allows, and the usual reasons a site gets in touch are unsealed openings around new pipes and cables and non-fire-rated filler around services. Most enquiries from Cyprus start with one failed joint and grow into a wider look at the building: we check the joints around it and give you an honest view of what needs doing now and what can wait.
In a London area such as Cyprus, buildings are refitted often, and every new cable, pipe or duct through a fire-resisting wall or floor leaves a gap. Each service penetration gets fire-rated or intumescent sealant if that’s what is specified, laid to the product’s tested arrangement.
Our 12-month guarantee is about workmanship, not wear and tear. Sealant wears with time, and movement, weather, cleaning and use decide how fast, so we spell out the cover before we begin.
- Place
- Cyprus (E6, E16)
- Wider area
- Greater London
- Cover
- 12 months on every job
- Quote
- Fixed quote, scope in writing
- Telephone
- 01277 525 020
- Page updated
- 3 November 2026
On site: what to expect
On arrival, we report to your site contact and complete whatever induction the building runs. Floors, finishes and fittings next to the joints are covered before anything is cut or cleaned, and the work usually takes anything from one day to a planned run of visits, depending on the number of seals and the access. In Cyprus, most buildings stay in use during the work, so zones and timings are agreed with whoever manages the building. Areas are handed back as each section is finished.
- First we confirm the product and tested details named in the specification.
- We sort the openings by the detail each one needs.
- Old or wrong materials are cut out.
- Mineral wool or other backing is fitted where required.
- Fire-rated or intumescent sealant goes in around the services and is tooled off.
- Completed areas are checked with you, with the records agreed when we quoted.
Getting the site ready
- For older buildings, check the asbestos register before work
- Flag any permit to work we’ll need
- Make sure the joints can be reached
Get a fixed quote
Send details, get a quote, we seal, guaranteed: that’s how every job runs. The first step is to speak to us on 01277 525 020 or send photos by email with what you know.
Read more
Do you need fire stopping in Cyprus?
Mixing products or improvising a detail breaks the link with the test evidence. An oversized gap, too shallow a bead, missing backing or two makers’ products combined are what we find most often.
Most enquiries start with one or more of the following:
- Head-of-wall gaps with no fire seal
- Expanding foam used as fire stopping
- Improvised or mixed-product fire seals
- Penetration schedules that need working through
At a college such as Newham College London, 2 miles to the north-west of Cyprus, checking penetration seals after summer M&E works is good practice.
Comparing quotes
- Will failed sealant be removed rather than covered?
- Whether primer will be used where the manufacturer specifies it
- What level of public liability insurance do they hold?
- How they handle RAMS and site documents
Cost factors for service penetrations
Quotes vary with the job. It mainly depends on:
- Location, for remote and island sites
- Induction, permit and paperwork requirements
- Access and working height
- How much existing material needs removing
Every site prices differently: the joint sizes, the specified product, access and working hours each have a bearing. Send the details and a fixed figure follows.
Sending details for a quote
However big the job, the same details help:
- The product your specification calls for
- What the building is and how it’s used
- Access details, including height
- Your programme or deadline
For a fixed quote, give us a call on 01277 525 020 or send details through our quote form, telling us the site location and the nature of the job. You can also send details through our quote form.
Maintenance after handover
After handover, these steps help:
- Get seals inspected before ceilings and boxing close
- Keep general-purpose fillers away from compartment walls
- Flag new cables with no seal around them
- Ask the designer to confirm details early on refits
Store the specified product details somewhere the next contractor can find them. It makes later repairs much easier to match.
Write fire stopping into the scope of any work crossing a compartment wall or floor. Then the seal goes in while the area is open, not months later.
What the job involves on each surface
Small ducts
We seal around ducts only within what the tested detail covers. The ductwork, its supports and any dampers are for the ductwork contractor.
Plastic pipes
Plastic waste pipes through slabs come up often. The detail decides whether sealant alone is enough, and we will never swap a specified collar for sealant.
Nearby places to Cyprus
What else we do in Cyprus
Cyprus: questions and answers
Can you take on a job at a hospital such as Cygnet Hospital Beckton?
Yes. Healthcare sites are among the places we work. Work is phased so departments keep running, under the site’s own rules.
Could you schedule work at a campus like University of East London for the vacation?
Yes. Education sites usually want the work in vacations or in phases during term, and we plan to suit. Let us know which documents your site asks for, and we’ll confirm them alongside the quote.
How do you choose the sealant?
The specification comes first, if there is one. If there isn’t one, it comes down to the joint: its movement, its surfaces and what it has to cope with.
Can you tell us what fire stopping our building needs?
No. Deciding what is needed sits with the designer, fire engineer and building control. Our role is fitting the specified fire-rated sealant, following the maker’s tested details.
How soon can the area be used again?
That comes down to the sealant and the temperature. Some products skin over quickly but need longer to cure fully, and we confirm it before leaving site.
Is it fine to apply new sealant on top of old?
No. Failed sealant is removed and the faces cleaned back to sound, dry material first, since fresh sealant will not bond reliably to aged material.
Can you follow the specification on our project?
Yes. Send it with your enquiry, and we will price the work to it.
Fire stopping in Cyprus: the local picture
Six care or nursing homes sit less than 2 miles from Cyprus. Care homes rely on fire-resisting walls and floors, and maintenance work that breaks through them leaves openings to seal. Fire stopping of openings and penetrations in England falls under Approved Document B. The national BS 476 classes are due to drop out of it from 2 September 2029, leaving the European BS EN 13501-2 route, subject to transitional arrangements. Either way, we install the specified product to its tested detail.
Shop fits on retail sites such as Beckton Retail Park, 0.5 miles north of Cyprus, can bring new services through fire-resisting walls between units, to be sealed with the specified product. At a university such as University of East London, less than half a mile south of Cyprus, labs, lecture blocks and residences are re-serviced often, so penetration seals are best checked after M&E work.
Cyprus is about 2 miles east of Canning Town, in Greater London. Cyprus sits inside our coverage and the rest of Greater London, and jobs here get the same fixed quote and 12-month guarantee as anywhere else. Our Greater London coverage takes in 764 places. There’s a separate page for London, about 7 miles away.
Business premises anywhere in E6 and E16 are within our area. If your site is on Strait Road, Harper Road and Trader Road or close by, we can quote for service penetrations. Just outside Cyprus, we also work in Beckton (1 mile north-east), North Woolwich (1 mile south), Royal Docks (1 mile west), East Ham (1 mile north) and Custom House (1 mile west). Further afield, our area takes in London (7 miles west), City of Westminster (9 miles west), Marylebone (9 miles west), Kensington (11 miles west), St Pancras (8 miles west) and Shoreditch (6 miles west).
Landmarks near Cyprus
Around Cyprus, our work takes us to commercial buildings near Oasis Academy Silvertown, London Design and Engineering UTC and Beckton District Park, among other places. The closest station to Cyprus is Woolwich station, about 1.3 miles south. Other landmarks nearby include Greenwich Castle (3.6 miles south-west) and Albert Dock Seamen's Hospital (1.1 miles west). For a walk, there’s Gilbert's Pit.