Fire stopping in Alkerton
Sealant work in Alkerton for main contractors, managing agents and facilities managers: fire-rated and intumescent sealing of service penetrations and linear gaps, with a fixed quote first.
- Fire-rated sealant that has cracked or shrunk back
- Seals disturbed by maintenance and left open
- Fire stopping installed outside its tested range
Need fire stopping in Alkerton?
Share the site address and what’s failing, and we’ll reply with a fixed quote or arrange a visit.
How a job runs
Our CSCS-carded applicators arrive with the sealants, primers and backing rod the job calls for. Joint faces are cleaned back to sound, dry surfaces, the manufacturer’s primer is applied where it’s called for, and each bead is tooled to a neat concave finish. For work around Alkerton, we aim to finish in one visit, so we ask for photographs and rough sizes first. Then the right materials arrive with us.
- We ask for the product and detail your designer has specified.
- Openings are measured and grouped by detail.
- Improvised fillers and failed sealant are removed.
- Mineral wool or other backing is fitted where required.
- Fire-rated or intumescent sealant goes in around the services and is tooled off.
- Completed areas are checked with you, with the records agreed when we quoted.
What we need from you
- Clear stock, furniture or equipment away from the joints
- Confirm the product named in the specification
- Warn occupants and staff about the work
Get a fixed quote
Quotes are fixed against the scope you send, so the cost is agreed before work starts. To ask for one, call 01277 525 020 or send details through our quote form.
Related advice
Fire stopping in Alkerton, done properly
Every service that crosses a compartment wall or floor leaves an opening, and that opening needs sealing to hold back fire and smoke. Our part is installing fire-rated and intumescent sealant at those openings and along linear gaps, where the specification calls for it. Each seal follows the manufacturer’s tested detail. If you have unsealed joints where partitions meet the slab and fire-stopping items raised at inspection or handover, we can put it right. Most enquiries from Alkerton start with one failed joint and grow into a wider look at the building: we check the joints around it and give you an honest view of what needs doing now and what can wait.
A job near Alkerton is typically planned around one visit, so send the specification and photographs first. Design and sign-off belong to the designer or building control; we install what’s specified.
Building owners and contractors get the same cover: a 12-month guarantee on our workmanship. It doesn’t extend to damage, faults in the building or work by others, and we’re upfront about that.
- Place
- Alkerton (OX15)
- Region
- Oxfordshire
- Cover
- 12 months on our workmanship
- Quotes
- Fixed quote, scope in writing
- Phone
- 01277 525 020
- Page updated
- 3 November 2026
When to bring in a specialist
Redoing a failed joint typically costs more than getting it right at the outset, because the whole bead must be removed and the faces cleaned back again. For that reason, many FMs and contractors use a sealant specialist from the outset.
The visible bead is only part of the job. Backing rod, primer where specified and a joint designed to move with the building are where general trades tend to cut corners.
When it isn’t the sealant
Honesty saves time and money. Fresh joints won’t solve:
- Designing or specifying fire stopping, which sits with the designer or fire engineer
- Fire risk assessments, a job for a competent assessor
- Gaps in walls that were never built as compartment walls
Not sure which it is? You can give us a call on 01277 525 020 or email us and we’ll tell you honestly before you book.
What we seal
- Linear gaps at wall heads
- Pipe penetrations
- Cable penetrations
- Small duct penetrations where the tested detail allows
- Joints between fire-resisting walls and floors
- Service gaps in risers
For managing agents and facilities managers
FMs need a contractor who is easy to get on site. Let us know the documents you need (RAMS, insurance certificate, CSCS details) and we’ll confirm them with the quote.
For main contractors, we work as the sealant subcontractor, on new build and refurbishment alike. Programme, specification and site rules come first.
What affects the price in Alkerton
Your fixed quote is built from the real scope. It allows for:
- Whether the work must be split into stages
- Removal of failed or old sealant
- Quantities, in metres or numbers
- Backing rod, priming and other preparation
There’s no price list, because the scope varies so much from one building to the next. For a fixed figure, call for a quote.
Before you send an enquiry
The more we know, the firmer the quote. When you get in touch, include:
- Approximate linear metres or a joint schedule
- Any dates the work must fit around
- How the joints are reached, and at what height
- What the building is and how it’s used
Every job follows the same four steps: send details, get a quote, we seal, guaranteed. The first step is to ring 01277 525 020 or email drawings and photos with what you know.
Towns and villages near Alkerton
Also in Alkerton
Fire-rated sealing for Alkerton buildings
Fire stopping of openings and penetrations in England falls under Approved Document B. The national BS 476 classes are due to drop out of it from 2 September 2029, leaving the European BS EN 13501-2 route, subject to transitional arrangements. Our part stays the same: the specified product, installed to its tested detail.
In a school such as Shenington Church of England Primary School, fire-rated sealant goes in around service penetrations where it is specified. At a college such as Wroxton College (2.5 miles east of Alkerton), checking penetration seals after summer M&E works is good practice. At a healthcare site like Horton General Hospital, 5.2 miles east of Alkerton, new services through compartment walls are a constant, and each needs the specified seal.
Alkerton is about 5 miles west of Banbury, in Oxfordshire. Across the OX15 postcode area, the process is the same: send details, get a fixed quote, we seal, and the work is guaranteed. Across Oxfordshire, 423 places are covered, including Alkerton. For work in that direction, see our Oxford page (25 miles or so).
If you need fire stopping in OX15, the process matches everywhere else we work: details, then a fixed price, then sealing and a 12-month guarantee. We also cover Shenington (1 mile west), Balscote (1 mile south-east), Shutford (2 miles south), Epwell (2 miles south-west) and Swalcliffe (3 miles south) for service penetrations. Nearby towns on our patch include Banbury (5 miles east), Chipping Norton (11 miles south-west), Neithrop (4 miles east), Grimsbury (6 miles east), Ruscote (4 miles east) and Bloxham (5 miles south-east).
Around Alkerton
Locally, jobs take us to sites close to The Bell Inn, among other places. Nearby you’ll also find Hanwell Castle (3.7 miles east) and W. O. Bentley Memorial Foundation (1.8 miles east). Green spaces nearby include Edge Hill and Woodford Bottom and Lamb's Pool.
Maintenance after handover
Your facilities or cleaning team can help the joints last. Pass these on to them:
- Flag new cables with no seal around them
- Foam or ordinary sealant is never a fire-seal repair
- Record which product was used where
- Ask which product is in place before decorating
During planned inspections, look at seals in risers, cupboards and voids. Look for cracks, unsealed new cables and gaps that have been enlarged and get them dealt with.
A simple record of seal locations and products helps. When a new service goes through, everyone knows which product and detail to match, and it helps at inspections.
FAQs: Alkerton
Will you plan work around the academic year at somewhere like Wroxton College?
Yes, holiday working periods are the norm on campus jobs. Let us know which documents your site asks for, and we will confirm them alongside the quote.
Can you work at a site such as Alkerton Oaks Business Park, by Alkerton?
Yes, sites like Alkerton Oaks Business Park are within our area, along with the rest of Alkerton. To start, just give us a call on 01277 525 020 or use the quote form with the unit, the joints involved and your access times.
Do you design or specify fire stopping?
No, that isn’t our role. With the designer’s details in hand, we can price the sealant elements.
How long before the joints can be used?
Curing time varies by product, and we confirm it on the day.
Can you work to our specification?
Yes. We follow the specification, along with the manufacturer’s installation guidance.
What if there’s asbestos in the old mastic?
Asbestos is possible in some older mastics, particularly in buildings from before 2000. Before we disturb old sealant in an older building, we ask to see the asbestos register or survey, and work stops until any suspect material has been tested. We don’t remove asbestos-containing materials.
Which standards are fire seals tested to?
BS EN 1366-3 covers penetration seals and BS EN 1366-4 covers linear joints. Classification follows BS EN 13501-2, where E is integrity, I is insulation and the number is minutes, as in EI 60. The rating applies to the product as tested.