Woolmer expansion joint sealing
Planning work on a movement joint in Woolmer? We assess it, carry out the work and guarantee our workmanship for 12 months.
- Previous reseals laid over old sealant
- Chipped joint edges on forklift routes
- Brittle, chalky sealant on external joints
Expansion joint sealing for Woolmer sites
Photos, a specification or a quick description of the joints is enough to start a fixed quote.
Signs you need expansion joint sealing in Woolmer
Repeated failure often traces back to the wrong product. Products not classed for the movement fail early. Movement capability is set out in BS EN ISO 11600.
Clients typically get in touch after noticing one or more of the following:
- Water dripping through deck or ramp joints
- Water getting into the wall through a failed joint
- Hardened, cracked sealant on exposed facades
- Sealant pulling off the joint face
At places like Southlands Industrial Park, which lies north-west of Woolmer, joints are sealed a section at a time so operations carry on.
Questions to ask before you book
- How they’ll work around occupants
- Will RAMS and insurance details be available?
- Their pre-qualification and accreditations
- How the existing material will be dealt with
Expansion joint sealing in Woolmer, done properly
Joint design counts for as much as the sealant itself. The joint has to be wide enough for the expected movement and the sealant’s movement capability, and depth is controlled using closed-cell backing rod, or bond-breaker tape in shallow joints. For wider joints, the width-to-depth ratio is often around 2:1, as the manufacturer advises, and the bead is tooled so it grips the two faces alone. If you’re dealing with expansion joints filled with dirt and stones and previous reseals laid over old sealant, we can help. Facilities teams, main contractors and managing agents in Woolmer tend to want the same three things: a clear scope, tidy work and joints that don’t fail again.
Around smaller places such as Woolmer, floor joints are often in barns and farm buildings turned into workshops, stores and offices. Joints in those slabs take vehicles, trolleys and foot traffic, and need a filler or sealant to match.
Work we carry out comes with a 12-month guarantee. Should something we installed fail, call the office on 01277 525 020 or use the quote form and we’ll come back to it.
- Location
- Woolmer (GU33)
- Region
- Hampshire
- Guarantee
- A 12-month guarantee
- Price
- A fixed quote before we start
- Telephone
- 01277 525 020
- Page updated
- 3 November 2026
Nearby places to Woolmer
More services for Woolmer
How a job runs
Site rules come first: sign-in, induction and whatever permit system the building uses. With the paperwork done, the joints are worked through in the order agreed with your site contact, and each area is checked before we leave it. For a building around Woolmer, tell us how to find it and who will meet us. Add it to your enquiry and we will build it into the plan.
- We assess the joints on site or from photos, noting widths and how each has failed.
- You receive a fixed quote stating the product and the movement it is rated for.
- Where areas have to stay open, we agree a phased sequence before starting.
- We strip the old sealant or filler and prepare each face until it’s sound and dry.
- Backing rod or bond-breaker sets the depth, primer goes on where specified, and the sealant is applied and tooled.
- We check each joint with you, confirm the cure time and sign off under our 12-month guarantee.
Getting the site ready
- Tell staff and tenants when we’ll be in
- Tell us which areas need to stay in use
- Tell us your opening times and when work is allowed
Getting a fixed quote
To get a fixed quote, speak to us on 01277 525 020 or email us with the site address and an outline of the work. You can also send details through our quote form.
Read more
Why it’s worth doing now in Woolmer
Closing a car park for a reseal is rarely an option. Phased work by bay or zone lets the rest stay in use. Tell us what has to stay open and we’ll plan around it. Older rural buildings around Woolmer move with the seasons, and rigid or tired sealant can’t keep up. The right product, sized to the joint, copes much better.
There’s no price list, because the scope varies so much from one building to the next. Call for a quote and we’ll price your job on its own details.
Why appoint us
- 12 months’ guarantee on every job
- Public liability insurance in place
- Constructionline member
- Work to your specification and the manufacturer’s guidance
Take a look at what affects the cost and how we’re accredited.
Expansion joint sealing in Woolmer: the local picture
Less than 3 miles from Woolmer there are at least three named estates and business parks. Their warehouses, yards and car parks are exactly where joints take the most punishment. Woolmer is in the South East, one of the UK’s drier regions. Even so, yard and car park joints are only sealed when they’re dry and clean, and gritting in cold spells finds its way into open joints.
In a school such as St Matthew's Church of England Aided Primary School, movement joints in brick, block and hall floors tend to be forgotten until they leak. For an estate such as Chase Hospital, 1.7 miles to the north-east of Woolmer, the joints in ramps, decks and long building elevations all need attention over time.
Woolmer is about 2 miles south of Bordon, in Hampshire. Our applicators travel to Woolmer for work on movement joints. Our Hampshire coverage takes in 723 places, large and small. Our Portsmouth page has more on work in that area (21 miles or so).
Commercial sites across GU33 are covered for movement joints. If your site is on Benhams Lane and Petersfield Road or close by, send details and we will quote for movement joints. If your building is just outside Woolmer, we cover Greatham (1 mile south), Blackmoor (1 mile north-west), Longmoor (1 mile south-east), Weavers Down (2 miles east) and Liss Forest (2 miles south). Further afield, our area takes in Farnborough (15 miles north), Fleet (13 miles north), Horndean (13 miles south-west), Aldershot (12 miles north-east), Alton (6 miles north-west) and Waterlooville (15 miles south-west).
Local landmarks in Woolmer
We work on buildings around Mill Chase Academy and the streets around them. The nearest railway station is Liss station, about 2.8 miles south. Well-known places in the area include Chase Community Hospital (1.7 miles north-east) and The Romany Museum (2.8 miles west). Green spaces nearby include Deadwater Valley and Selborne Hill.
Your questions answered
Is a smaller place like Woolmer outside your area?
No. Places such as Woolmer are covered as much as the big towns. We work across Greater London and the South East. We plan jobs in smaller places so return trips are kept to a minimum.
Do you take on work at healthcare sites like Chase Hospital?
Yes, provided the work is planned with the site’s estates team. We follow the site’s permits, sign-in and infection-control procedures in every area.
Do you offer coloured sealant?
Often, yes. Sealants are made in a wide range of standard colours, and matching to RAL references or nearby finishes is commonly requested. We confirm what’s available for the specified product when we quote.
Are you insured?
Yes. We are fully insured, including public liability cover.
Can you follow the specification on our project?
Yes. Include it with the drawings when you ask for a quote, and we’ll price the work to it, flagging anything that needs clarifying.
What sealant do you use in movement joints?
It depends on the movement, exposure and traffic. Facades often take a low-modulus silicone; floors and decks typically need a polyurethane unless the specification names something else.
Which sealant will you use?
A specification, where there is one, decides it. If there isn’t one, it comes down to the joint: its movement, its surfaces and what it has to cope with.
For managing agents and facilities managers
Hotels, schools, healthcare sites, offices and retail units come to us directly as well. The work is planned around how the building runs, so the building keeps working while we do.
We take on planned maintenance as well as one-off repairs: resealing failed joints building by building, on a schedule that suits your budget. Woolmer can form part of a wider programme.
Keeping the joints sound
Problems stay small when the joints are checked regularly. In particular:
- Leave barriers in place until fresh joint sealant has cured
- Treat a small split as a warning, not a cosmetic issue
- Record the sealant used and the date in the O&M file
- Check joints after long freezing spells
Debris does more harm to joint sealant than most people realise. Grit trodden or driven into the joint works at the surface until it tears, especially on car park decks and warehouse floors. Regular sweeping keeps joint lines clear.
Rain gets into walls through torn brick and block movement joints. The first sign is often a damp patch indoors, well after the seal first opened. Catching it early keeps the water outside.
Doing it in-house
What you see is the finished bead, but most of the work is hidden. Backing rod, primer where specified and a joint designed to move with the building are where general trades tend to cut corners.
Site maintenance staff can often handle a short internal joint. Where it goes wrong is preparation: sealing over old material, sealing onto damp or dusty surfaces, or a product that can’t take the movement.