Liss Forest expansion joint sealing
Expansion joint sealing in Liss Forest, backed by over 20 years in commercial sealing. Fully insured and CHAS accredited.
- Water dripping through deck or ramp joints
- Expansion joints split through the centre of the bead
- Previous reseals laid over old sealant
Need expansion joint sealing in Liss Forest?
Share the site address and what’s failing, and we’ll reply with a fixed quote or arrange a visit.
On site: what to expect
We begin with a short walk round with whoever looks after the building, agreeing which joints are in scope, where to start and what must stay open. After that, any old or failed material is removed, each joint is prepared and the new sealant goes in. If others near Liss Forest need work, visits can be combined. A fixed quote is given before anything starts.
- The first job is to check each joint: how wide it is, how it moves and why the old seal let go.
- Next, we fix a price and confirm the sealant we propose for the movement.
- Old sealant and filler are cut out and the joint faces cleaned back to sound material, flagging any broken edges that need repair before sealing.
- Backing rod goes in at the right depth, or bond-breaker tape where the joint is shallow.
- Where the maker calls for primer, it’s applied first, then the bead goes in and is tooled to a concave finish.
- Finished joints are checked and backed by our 12-month guarantee.
What we need from you
- Flag any permit to work we will need
- Share your working hours and any access restrictions
- Send asbestos survey details if the building is pre-2000
Ask for a quote
Tell us about the building, the joints and when you need the work done, and we’ll put a fixed quote together. To get it moving, phone 01277 525 020 or email the details over.
Read more
How we handle expansion joint sealing in Liss Forest
Floor movement joints in warehouses, retail and public buildings carry wheeled traffic. Without a sound filler, joint edges chip and spall under load so the product has to suit both the traffic and the movement. We’ll tell you if the edges need repairing before sealing and phasing can keep areas working. We work on precast concrete panel joints, podiums and floor movement joints and car park decks and ramps, and the usual reasons a site gets in touch are new sealant over old, now failing and expansion joints filled with dirt and stones. Facilities teams, main contractors and managing agents in Liss Forest tend to want the same three things: a clear scope, tidy work and joints that don’t fail again.
For a site near Liss Forest, measurements and photographs up front mean one trip where possible. Tell us the joint widths if you can, and what drives or walks over them.
Building owners and contractors get the same cover: twelve months on the work we carried out. Faults in the structure, damage and other trades’ work fall outside it, and we say so plainly.
- Location
- Liss Forest (GU33)
- Wider area
- Hampshire
- Cover
- 12 months on our workmanship
- Quote
- Quoted before any work starts
- Call
- 01277 525 020
- Page updated
- 3 November 2026
Questions we are asked in Liss Forest
Is Liss Forest too small for you to travel to?
No. Places such as Liss Forest are covered as much as the big towns. Our area covers London and the South East counties. Good photos up front let us bring everything on the first visit.
Do you cover business parks and estates near Liss Forest, such as Ham Barn Business Park?
Yes. Our area takes in Liss Forest and its surroundings, with estates and business parks such as Ham Barn Business Park included. A few photographs and the unit address let us price the work.
Who decides which product is used?
If the job is specified, we follow the specification. If not, we choose for the movement, the surfaces and the conditions, in line with the manufacturer’s guidance.
Can you seal car park deck joints?
Yes, we do. Tyre loads, grit and de-icing salts make these some of the hardest joints to keep sealed and broken edges are flagged before sealing.
How long will the joint resealing take?
Expect anything from part of a day to a couple of weeks, depending on joint lengths, widths and access, with phasing where areas must stay open. We’ll confirm when each area can be used again.
What hours do you work?
The office is staffed Monday to Friday, from 8am until 5pm. Let us know your site hours and access windows, and the work will be planned around them.
What happens if it rains on the day?
Sealing onto a damp surface leads to adhesion failure. We agree a revised date with you.
Leave it or put it right?
Leaving a failed movement joint rarely stays a small problem. Grit and water fill the gap and the material either side breaks up and the job grows to repairs as well as sealing. Resealing early keeps the work to sealant. Older rural buildings around Liss Forest move with the seasons, and rigid or tired sealant can’t keep up. The right product, sized to the joint, copes much better.
A quote for movement joints depends on quantities, condition and access, plus any specification you’re working to. Call for a quote.
Why appoint us
- Matching to RAL references, product permitting
- Work carried out by CSCS-carded applicators
- One contact handling all your sites
- Failed material removed, not covered up
How the job changes by surface
Brickwork and blockwork joints
Masonry faces are often porous, dusty or crumbly. Faces are prepared and primed wherever the sealant maker calls for it.
Car park decks and ramps
Deck and ramp joints take tyre loads, grit and de-icing salts. We use a sealant made for wheel loads and the expected movement.
Site staff or a sealant specialist?
The visible bead is only part of the job. Correct depth, the right primer and a sealant matched to the movement are where general trades tend to cut corners.
For most general trades, sealant is a sideline. A specialist prepares properly, controls joint depth and picks a product with the right movement class.
Quoting for work in Liss Forest
Quotes vary with the job. It mainly depends on:
- The site’s rules and procedures
- Working within restricted access windows
- Which sealant the job calls for
- The size and state of each joint
The product called for affects the cost, and so does the preparation, such as cutting out, priming or new backing rod. Access, phasing and site rules also count.
What we need to price the job
A few photos plus some basic facts will normally do. It helps to include:
- Drawings or a marked-up plan, if available
- Photos of the joints, close up and from further back
- Access details, including height
- Where the site is, with the postcode
Every job follows the same four steps: send details, get a quote, we seal, guaranteed. The first step is to ring 01277 525 020 or email the details over with what you know.
Also in Liss Forest
What we are called out for in Liss Forest
Weathering wears down sealant on exposed elevations and decks. In time the bead chalks, stiffens and cracks and opens at the next temperature swing.
What tends to prompt an enquiry:
- Rain penetration at brick or block movement joints
- Expansion joints filled with dirt and stones
- Spalled or broken joint edges in floors and decks
- Brittle, chalky sealant on external joints
Another example is Longmoor Enterprise Park, which lies north of Liss Forest, where floors and yards would be done in stages around the occupiers.
Questions to ask before you book
- Whether primer will be used where the manufacturer specifies it
- Can the work be phased to keep areas open?
- What site paperwork they can supply
- Who will actually carry out the work
Where floor joints take the most wear near Liss Forest
The 3 miles around Liss Forest take in at least three named trading estates, business parks or retail parks. That puts plenty of warehouse floors, service yards and car parks close by, all with joints under traffic. At about 46 miles from central London, Liss Forest is within reach of the capital. The South East has large numbers of industrial estates and warehouses along the motorway corridors, and their floor joints take forklift and pallet-truck traffic all day.
Office parks like Ham Barn Business Park, 0.8 miles to the north-west of Liss Forest, have decks, ramps and clad elevations whose joints take movement every day. For a school such as Liss Infant School, playground and building joints can be done in the holidays.
Liss Forest is about 4 miles north-east of Petersfield, in Hampshire. We cover commercial sites throughout Liss Forest. 723 places across Hampshire fall within our area, Liss Forest among them. We also cover Portsmouth, some 19 miles away.
Commercial sites across GU33 are covered. For a building on Forest Road, Warren Road and Newfield Road or nearby, we can quote for movement joints. We also cover The Mint (1 mile south-east), Liss (1 mile south), West Liss (1 mile south), Greatham (1 mile north) and Rake (1 mile south-east) for movement joints. Bigger towns within reach include Havant (14 miles south), Fleet (15 miles north), Horndean (11 miles south-west), Aldershot (14 miles north), Alton (8 miles north-west) and Waterlooville (13 miles south-west).
Around Liss Forest
Around Liss Forest, our work takes us to commercial buildings near The Temple Inn, among other places. Liss Forest’s nearest station is Liss station, roughly 0.7 miles south-west. Other landmarks nearby include Chase Community Hospital (3.8 miles north) and The Romany Museum (3.7 miles north-west). Not far away are Liss Riverside Railway Walk North and Wheatham Hill.