Wasbister expansion joint sealing
Work needed on a movement joint in Wasbister? We assess it, carry out the work and guarantee our workmanship for 12 months.
- Brittle, chalky sealant on external joints
- Joints packed with grit and debris
- Torn sealant in brick or block movement joints
Expansion joint sealing in Wasbister
Send drawings, photos or a joint schedule, or tell us about the site, and we’ll come back with a fixed quote.
Expansion joint sealing for commercial buildings in Wasbister
Our movement joint work takes in walls, panels, decks and floors: vertical joints in brick and block facades, joints between precast or cladding panels, concrete slab and deck joints, ramps, podiums and internal floors. Every one calls for a sealant picked for its movement, exposure and traffic. Site teams most often ask us about movement joints with split or torn sealant and joints where the bead has lost adhesion, on brickwork movement joints, podiums and floor movement joints and blockwork control joints. Sealant contractors, mastic applicators, sealant specialists: whatever the job title on the order, the work in Wasbister is the same: the right product in a properly prepared joint.
For outside joints near Wasbister, the Scottish weather sets the timetable: sealant needs a dry joint and a temperature within its range. Inside slabs aren’t affected and can be scheduled around the occupier.
Every job is signed off with a 12-month guarantee. It’s a plain promise: if our work fails within that year, we put it right.
- Where
- Wasbister (KW16)
- Region
- Orkney Islands
- Guarantee
- A 12-month guarantee
- Price
- Quoted before any work starts
- Telephone
- 01277 525 020
- Updated
- 3 November 2026
What sets the cost
Quotes vary with the job. It mainly depends on:
- Induction, permit and paperwork requirements
- Backing rod, priming and other preparation
- Any access equipment needed
- Location, for remote and island sites
Small jobs and large programmes are priced from the same things: what’s in scope, how we reach it, what’s specified and when it needs doing. Call for a quote, and you’ll have a fixed figure to work with.
What we need to price the job
Whether it’s one area or a whole building, the same details help:
- Drawings or a marked-up plan, if available
- The postcode of the building
- Whether an asbestos survey exists
- Any specification or named product
A good quote starts with a clear picture: the joints involved, quantities, access and the product called for. Send what you have, and we will arrange a site visit if anything is unclear.
More services for Wasbister
Traffic, movement and joints around Wasbister
Wasbister sits close to the coast, within about 1 mile. Near the sea, external slabs, ramps and decks see salt air and driven rain as well as their usual loads, so it pays to keep them sealed. Wasbister is on Scotland’s drier eastern side. Frost and winter road salt still work into open joints in car parks and yards. Sealing them in drier months limits winter damage.
A campus such as Heriot-Watt University - Orkney Campus (4.1 miles south-west of Wasbister) has long runs of movement joint in its buildings, decks and paving.
Wasbister is about 11 miles west of Kirkwall, in the Orkney Islands. Our applicators travel to Wasbister for work on movement joints, handled exactly as we handle every other area. We work across 51 places in the Orkney Islands.
If you need expansion joint sealing in KW16, the process matches everywhere else we work: details, then a fixed price, then sealing and a 12-month guarantee. With the B9055 nearby, Wasbister is straightforward for us to reach. Sites close to Wasbister are covered too, including Tenston (1 mile north), Grimeston (2 miles east), Russland (2 miles north-east), Bimbister (3 miles east) and Harray (3 miles north-east). Island and remote sites need extra planning, with travel, ferry crossings where needed and weather to allow for, so mention the location when you call the office on 01277 525 020 or use the quote form.
Landmarks near Wasbister
A little further out are Skara Brae Visitor Centre (3.6 miles north-west). Open spaces near Wasbister include Brodgar RSPB Reserve and Hill of Miffia.
Maintenance after handover
Every sealant joint needs some looking after, and how long they last depends on how they’re treated. We suggest:
- Inspect exposed joints once the cold weather has passed
- Include every elevation and deck joint in periodic inspections
- Keep traffic off new joints until the cure time is up
- Keep stones and debris out of open joint lines
Movement joints belong on the planned maintenance inspection list. A periodic look picks up tears and lifting before water gets in and long before edges start to break. Should you spot a problem, you can call the office on 01277 525 020 or send details through our quote form and send a picture.
An open joint fills with grit, and a joint full of grit can’t close. The arrises crack and break away under the load and the reseal becomes an edge repair as well. Keeping the seal sound avoids all of that.
Do you need expansion joint sealing in Wasbister?
Three-sided adhesion is a common cause of early failure. Bonded on three faces, it can’t stretch evenly when the joint opens so backing is set before sealing.
Common reasons buildings call us in:
- Sealant pulling off the joint face
- Expansion joints filled with dirt and stones
- New sealant over old, now failing
- Chipped joint edges on forklift routes
For floors and slabs around Wasbister, the product is chosen for the traffic and the movement at each joint.
Before you book anyone
- Health and safety accreditation such as CHAS
- Can the work be phased to keep areas open?
- Whether old or failed sealant will be cut out, not overlaid
- How they handle RAMS and site documents
Doing it in-house
For a quick touch-up, site staff may be fine, but anything bigger is another matter: a specialist brings efficiency, a consistent finish and a 12-month guarantee.
Some joints are best left to specialists: fire-rated seals that must follow a tested detail, trafficked floor joints and external movement joints among them. Getting these wrong usually costs more in the end than doing them right.
From enquiry to sign-off
At the end of each section, we remove the tape, clean down and inspect every joint with your site contact. Where the sealant needs time to cure before use, we tell you and sign the area. Jobs near Wasbister are often grouped with others in the same area, to make the most of each trip. Let us know if your dates have any give.
- Photos, joint lengths and drawings come to us, or we visit.
- We compare each joint’s width with the movement and the sealant’s capability, and flag anything that needs an engineer.
- Old sealant and debris are cut out of every joint.
- Any broken arrises or friable edges are flagged before work goes further.
- The right sealant goes in at the right depth, bonded to the two sides only.
- Each area is handed back after its cure time, under our 12-month guarantee.
Before we start on site
- Tell us what induction or permit system the site runs
- Share your working hours and any access restrictions
- Share the asbestos register for older buildings
Get a fixed quote
If there’s a specification, drawings or a tender package, send it with your enquiry, and we will price against exactly what is specified. Smaller jobs need nothing more than photos and a few notes.
Read more
How the job changes by surface
Internal floor movement joints
Wheeled traffic chips floor joint edges that aren’t supported. The right filler or sealant for the traffic and movement protects them, and tell you if edges need repairing first.
Concrete and precast panel joints
Joints between precast panels open and close with temperature and loading. The sealant needs the right movement capability and a controlled depth.
Questions about Wasbister
Will our site in Wasbister have to close for joint sealing?
Usually not: we work in sections and hand each one back once it has cured. Tell us which hours and entrances we can use and we’ll plan from there.
Can you take on a job in Wasbister, on the island?
Yes. Islands are part of our area, Wasbister included. We plan island jobs around the ferry and the forecast, and bring everything the job needs on the first crossing.
Do you hold CHAS accreditation?
Yes. We are CHAS accredited, we are a Constructionline member and we use CSCS-carded applicators.
Is colour matching possible?
That depends on the product. Some ranges are wide, others limited, so we will confirm the colours available for the specified product with the quote.
Can you quote from photographs?
Photos, drawings or a schedule are often enough to quote. If the job needs a look first, we’ll arrange a visit before quoting.
Can weather delay the job?
Outside, yes. The joint has to be dry and within the product’s temperature range, so damp, frosty or very cold days can stop external work. Internal work is rarely affected.
Will you just go over the old sealant?
No. Overlaying old sealant is a frequent cause of early failure, so it all comes out first.