Coloured and colour-matched sealant in Skeabrae, Orkney Islands
Coloured and colour-matched sealant for visible joints in Skeabrae and across the Orkney Islands. CHAS accredited and fully insured, with a 12-month guarantee.
- Hotel refurbishments with a set colour scheme
- Old sealant that has yellowed, darkened or faded
- Old colour-matched joints lifting at the edges
Coloured sealant for Skeabrae sites
Share the site address and what’s failing, and we’ll reply with a fixed quote or arrange a visit.
Coloured sealant for commercial buildings in Skeabrae
Where colour is critical, a sample bead in a discreet spot settles the question. Sealant can look slightly different once it has cured, and again in different light. Let us know who signs off colour, and we will fit the sample into the programme. If you are dealing with standard-colour sealant spoiling a high-end finish and sealant that no longer suits recoated frames, we can help. One point of contact handles commercial sealant work in Skeabrae from the first photographs to the final walk-round, for single jobs and planned programmes alike.
Travel to smaller places such as Skeabrae is planned so the whole job is finished in one visit where possible: send photographs and a complete list so the right products and colours come on the day. Several jobs nearby can also be put together.
The 12-month guarantee is for workmanship rather than wear and tear. Sealant wears with time, and movement, weather, cleaning and use decide how fast, so we are clear about what is covered before work starts.
- Place
- Skeabrae (KW17)
- Wider area
- Orkney Islands
- Cover
- A 12-month guarantee
- Quotes
- Fixed quote, scope in writing
- Telephone
- 01277 525 020
- Page updated
- 3 November 2026
Site staff or a sealant specialist?
For most general trades, sealant is a sideline. A specialist brings correct preparation, depth control with backing rod and a product suited to that particular joint.
Paperwork matters too. Many sites expect CSCS cards, RAMS and proof of insurance, and we will confirm the paperwork you need with the quote.
Cost factors for colour-matched joints
Sealant work doesn’t have a standard rate, because every site is different. What we take into account:
- Access and working height
- How much existing material needs removing
- Location, for remote and island sites
- The product specified
Every site prices differently: the joint sizes, the specified product, access and working hours each have a bearing. A fixed quote follows once we understand the job.
What to include in your enquiry
A few photographs plus some basic facts will normally do. Please tell us:
- Specification clauses that apply
- Rough lengths or quantities, or drawings if you have them
- Asbestos survey details if the building is older
- The type of building and who uses it
Need a figure for a tender or a budget? We will quote against your scope and drawings that you can work with. If you have questions first, ring 01277 525 020 or email a schedule or drawings.
Other services in Skeabrae
What we can’t put right
A proper diagnosis includes knowing what sealant can’t do. You’ll hear from us if the cause turns out to be one of these:
- Finishes that change colour from one area to another
- Exact bespoke colour matches beyond the product’s range
- Overpainting a joint that needs a non-paintable product
If in doubt, call 01277 525 020 or email us and we’ll say what we think before you book.
Where we work in Skeabrae
- Powder-coated and anodised frames
- Natural stone and brick
- Office fit-out finishes
- Hotel bathrooms and public areas
- Shop-fit joinery and counters
- Cladding panels
Common questions from Skeabrae clients
Can you supply sealant in our brand colour for a site in Skeabrae?
Yes, sealants come in a wide range of standard colours, and matching to RAL references, cladding, stone or frames is a common request. Send colour references or photographs and we will confirm what’s available for the product.
Is Skeabrae inside the area you cover, given it’s on an island?
Yes. Islands are part of our area, Skeabrae included. We plan island jobs around the ferry and the forecast, and bring everything the job needs on the first crossing.
How soon can the area be used again?
The product and site conditions decide that. Some take light use quickly, others need longer to cure, and we confirm it before leaving site.
Are you CHAS accredited and on Constructionline?
Yes. Mastic Doctor is CHAS accredited and a Constructionline member.
Can you fit around our working hours?
Mention the site’s hours and access windows in your enquiry, and we’ll plan around them. Our office runs Monday to Friday, 8am until 5pm.
Is it fine to apply new sealant on top of old?
No. We cut the old material out and clean the joint back before sealing, since fresh sealant will not bond reliably to aged material.
Can you work while the building is occupied?
Yes, with some planning. Tell us your site hours and access windows and we will plan around them.
Frontages, fit-outs and joints in Skeabrae
The sea is no more than about 3 miles from Skeabrae. Exposed frontages near the sea are hard on sealant, so the product has to suit the weather as well as the look. Sea-facing elevations are typically where failed joints show first. Being in the east of Scotland, Skeabrae gets less rain than the west coast. Cold snaps still affect when external joints can be sealed.
In hotels such as Smithfield Hotel (1.2 miles east of Skeabrae), refurbishments usually mean bathroom, bar and reception joints where a matched sealant colour has to sit with the finishes. Whatever the building in Skeabrae, commercial sealant work starts with cutting out the failed bead and cleaning the joint back to sound material.
Skeabrae is about 13 miles north-west of Kirkwall, in the Orkney Islands. Commercial clients in Skeabrae can call on us for colour-matched joints. We work across 51 places in the Orkney Islands.
We take on colour-matched joints across the KW17 postcode area, whatever the building. We also cover Dounby (1 mile east), Hourston (2 miles south-east), Scarwell (2 miles west), Russland (3 miles south-east) and Tenston (3 miles south). Where a site is remote or on an island, we plan travel and materials carefully, so the full address helps from the start.
Landmarks near Skeabrae
Nearby you’ll also find Earl's Palace (4.6 miles north-west) and Kirbuster Farm Museum (2.8 miles north). Green spaces nearby include Orr Shun and Greeny Hill.
How the job changes by surface
Powder-coated and anodised frames
Frames finished to a RAL reference are a frequent colour-matching job. The frame colour is checked against what the product is made in, and the nearest option is agreed.
Office fit-outs
In offices, sealant appears at partitions, tea points, washrooms and reception desks. Colour-matched joints keep the finish consistent across floors at handover.
Our process
Before any cutting starts, the area is protected: masking tape along the joint edges and sheeting over anything nearby. On site, the work typically takes about the same time as any other sealant work, plus a little longer if a sample bead is agreed first, and our waste is bagged and taken away as we go. Where we can, we combine work around Skeabrae with other jobs nearby, to make the most of each trip. Let us know if your dates have any give.
- We start with photos, drawings or a visit to see the finishes.
- We send the closest colours from the product’s range.
- Tell us your site hours and access windows and we will plan around them.
- Joints are prepared, primed where specified and backed.
- We seal in the approved colour and tool it smooth.
Getting the site ready
- Point out any areas we must not close
- For older buildings, check the asbestos register before work
- Have the specification and drawings to hand
Request a quote
Quotes are fixed against the scope you send, so the cost is agreed before work starts. To start the process, phone 01277 525 020 or send photos by email.
Advice
Aftercare for building managers
Sealant joints are maintenance items, and how long they last depends on how they’re treated. We suggest:
- Standardise colours across a portfolio
- Agree the sealant colour early and write it into the specification
- Check a trial length in real light
- Avoid piecemeal repairs on coloured joints
Keep a record of the product and colour reference used. Future repairs can then use the same colour, with no guesswork.
Standardise the sealant colour on multi-site work. It keeps repairs and new sites consistent.