Essex · England
Commercial sealant contractors in SS12
We cover every part of the SS12 postcode district, including Wickford, Nevendon and Shotgate. Every joint is properly prepared, with a 12-month guarantee.
Sealant work in SS12
Photos, a specification or a quick description of the joints is enough to start a fixed quote.
Where we work in SS12
Our services across SS12
- Construction and new-build mastic
- Commercial washroom and wet-area sealing
- Expansion and movement joint sealing
- Fire-rated sealing and fire stopping
- Commercial sealant contractors
- Coloured and colour-matched sealant
- Industrial and floor joint sealing
- Mastic sealing for building owners and managing agents
- Facade and window perimeter sealing
- See all services
Tell us what needs doing and your postcode for a fixed quote: give us a call on 01277 525 020 or email drawings and photos.
Nearby postcode districts
More in Essex
Every town in Essex
Every area we cover
Our commercial sealant contractors service in SS12
Most commercial buildings carry hundreds of metres of sealant that nobody thinks about until it fails, and on a working site that typically surfaces as a leak, a stain or a complaint from occupiers. We are commercial sealant applicators for FMs, managing agents, landlords and contractors. Our job is to diagnose the failure, remove the old bead and seal again using a product chosen for the movement and exposure. Most enquiries involve frame mastic that has hardened and come away from the wall and untidy joints in a reception, shop floor or lobby, on kitchen worktops and splashbacks, window and door perimeters and floor and threshold joints.
When we get to site, we sign in, go through any site induction and check how permits are handled. Floors, finishes and fittings next to the joints are covered before anything is cut or cleaned, and the work usually takes anything from part of a day on a short run of joints to several weeks on a large phased package.
- You send photos, drawings or a list of the joints and areas involved, or we arrange a site visit.
- The failure is diagnosed and a fixed quote issued for the work agreed.
- Site hours, access windows and the order of areas are agreed before we start.
- Failed sealant is cut out and each joint cleaned back to sound, dry faces.
- The depth is set, primer is used where the maker calls for it, and the fresh bead is applied and tooled.
- Finished joints are checked with you and handed over with our 12-month guarantee.
How we quote
Access can matter as much as the joints themselves: easy-to-reach joints are quicker than those that need equipment to get to. Tell us how the joints are reached and call for a quote.
What you get with us
- Work carried out by CSCS-carded applicators
- CHAS accredited contractor
- Sealing commercial buildings since 2005
- A range of standard colours, depending on the product
Get a fixed quote
The quickest route to a quote is a few photos and the site postcode. Send them through the quote form, or call the office on 01277 525 020 or email the details over to discuss it first.
Around Wickford
We work on buildings around St Andrew, Oakfield Primary School and Beauchamps High School. Wickford’s nearest station is Wickford station, about 0.7 miles north-west of the centre. Nearby you’ll also find Rayleigh Castle (3.6 miles east) and Battlesbridge Motorcycle Museum (2.2 miles north-east). Open spaces near Wickford include Shotgate Thickets.
Commercial premises across SS12
From Wickford, Shotgate and North Benfleet outwards, SS12 has a broad spread of commercial premises: shops, offices, hotels, restaurants and units. Because we cover all of it, multi-site occupiers can bring every building under one quote.
All of Greater London is inside the ULEZ, and much of the South East is within easy reach of the capital, so jobs in SS12 are planned with access, loading and parking in mind.
Wickford: A business with units at Cricketers Retail Park and Burnt Mills Industrial Estate needn’t use two contractors for its sealant. Retail sites such as Cricketers Retail Park, 1.5 miles to the south-west of Wickford, are typical of where shop-fit joints, frontages and staff areas need neat, colour-matched sealant.
Doing it in-house
A short, simple internal joint is often within reach of a maintenance team. Where it goes wrong is preparation: sealing over old material, sealing onto damp or dusty surfaces, or a product that can’t take the movement.
What you see is the finished bead, but most of the work is hidden. Backing rod, primer where specified and a joint designed to move with the building are where general trades tend to cut corners.
Looking after the joints
To get the most from the new sealant:
- Log reseals in the O&M or maintenance records
- Keep abrasive pads and scrapers off resealed joints
- Check sealant as part of routine building inspections
- Have extract fans checked so wet areas dry out
New joints need their full cure time before they take water, cleaning or traffic. That time depends on the product, the temperature and the joint depth. Keeping signs or barriers up until then protects the finish.
Movement joints that fill with debris stop working. The joint can no longer close, so its edges crack or spall. At that point it’s a repair job rather than a reseal.
Honest limits
A few problems need another trade or a different fix, and we point that out rather than sealing over them:
- Walls or slabs moving more than any sealant can take
- A dripping trap, valve or pipe behind a fitting
- Misted, cracked or failed glazing units (a glazier’s job)
What happens if it’s left?
It can be tempting to hold sealant work back until the next refurbishment. That’s reasonable for internal joints that are just tired-looking, but external and wet-area joints that already leak shouldn’t wait. Splitting the scope into now and later is often the sensible compromise.
Comparing quotes
- Whether their applicators hold CSCS cards
- Do they follow the manufacturer’s priming guidance?
- How the existing material will be dealt with
- How they handle RAMS and site documents
How the quote is worked out
We price every job individually. The main factors are:
- The size and state of each joint
- Whether old sealant has to be cut out first
- Any access equipment needed
- Location, for remote and island sites
The product called for affects the cost, as does the preparation each joint needs. Access, phasing and site rules also count.
Details that help us quote
For an accurate fixed quote, we need to understand the site. Useful things to include:
- Clear photographs of the problem areas
- Approximate linear metres or a joint schedule
- The postcode of the building
- How the joints are reached, and at what height
We quote a fixed sum against the scope you give us, so the cost is agreed before work starts. To start the process, give us a call on 01277 525 020 or email the details over.
Questions we are asked in SS12
Do you take on multi-site sealant work?
Yes. We regularly take on multi-site work and planned maintenance programmes.
Which sealant will you use?
If the job is specified, we follow the specification. Otherwise, we recommend a product to suit the joint’s movement, the substrate and the conditions, following the manufacturer’s guidance.
How long will the new sealant last?
There’s no fixed lifespan: movement, exposure, cleaning, traffic and the product all play a part. Treat them as maintenance items and inspect them regularly.
Is it OK to apply fresh sealant over existing beads?
The old bead is stripped out first. Then the joint is cleaned, primed where the maker specifies, backed to depth and resealed.
Will your applicators have CSCS cards?
Yes. If you need card details for site access, let us know and we’ll send them with the quote.
How long does a job like this take?
That varies with the scale of the job, though a typical visit typically takes as long as the agreed scope needs, from a single visit to a programme spread over several weeks. Larger or phased jobs take longer, and we will give you a timescale with the quote.
Are you CHAS accredited and on Constructionline?
Yes. We’re CHAS accredited and a Constructionline member.